RTS KP-12 System Installation Manual
Adam advanced digital audio matrix
Hide thumbs
Also See for KP-12:
- Installation instructions manual (30 pages) ,
- Replacement instructions (2 pages) ,
- User instructions (106 pages)
Related Manuals for RTS KP-12
Summary of Contents for RTS KP-12
- Page 1 ADAM™ Advanced Digital Audio Matrix System Installation Guide 9330-7467-000 Rev G July 2006...
- Page 2 The product information and design disclosed herein were originated by may request from Factory Service a different shipment method). Any and are the property of Telex Communications, Inc. Telex reserves all shipment upgrades will be paid by the customer. The equipment should patent, proprietary design, manufacturing, reproduction, use and sales be shipped in the original packing carton.
-
Page 3: Table Of Contents
Chapter 2 - Intercom Port Connections ............................7 General Information ................................7 Logical Keypanel Numbers ..............................7 General Procedure for Connecting Devices to the Intercom ....................8 KP-12 Installation Notes ............................... 8 KP-32 Installation Notes ............................... 9 Addressing the KP-32 ................................9 Program Source Notes ................................9 TIF Telephone Interface Installation Notes .......................... - Page 4 Viewing the Program Source for an IFB ..........................24 Viewing What IFBs a Program Source Feeds ........................24 Assigning Source and IFB Keys ............................24 UIO-256 Input/Output Frame .............................25 Connecting a single UIO-256 Frame ..........................25 Connecting Additional UIO-256 Frames ..........................25 Programming the UIO-256 ..............................25 Connecting to the SSA-324 ..............................26 General Description ................................26 Installation ..................................26...
- Page 5 Table Content...
-
Page 7: Chapter 1 - Introduction
CHAPTER 1 Introduction Unpacking the Components Unpack the contents of the shipping crates and carefully inspect for damage. Notify the freight carrier immediately if any damage is noted. Check off all items as noted in the packing lists. SAFETY TIP: Use caution when lifting the system components. A fully loaded ADAM Card Frame, for example, weighs approximately 75 lbs (34kg). -
Page 8: Card Removal And Installation
Introduction Card Removal and Installation All ADAM circuit cards can be “hot-installed”, which means you do not have to turn the power OFF before installing or removing a card. This permits continuous operation of the intercom system - with no interruptions to unaffected ports - in the event of a card failure. -
Page 9: Ac Power Connection
AC Power Connection To install a power supply, set the power switch on the front of the supply to the OFF position. Push the power supply firmly into the slot in the ADAM frame so that the connector sits properly in the slot, then tighten the captive screws. AC Power Connection Place the AC switches on the back panel of the ADAM frame in the OFF (O) position. - Page 10 Introduction...
-
Page 11: Chapter 2 - Intercom Port Connections
CHAPTER 2 Intercom Port Connections General Information Typically, devices are connected to individual intercom ports using Station Breakout Panels as shown in the in the drawings starting on page 33. Depending on the type of breakout panels being used, the individual intercom stations will utilize either RJ-11 modular style intercom cables, or 9-pin D-sub cables. -
Page 12: General Procedure For Connecting Devices To The Intercom
Plug in the AC power cords for the KP-12 and any connected expansion panels, and turn ON the power. When the KP-12 is connected and turned ON for the first time, the call waiting window will display “SET ADDR”. Tap the SELECT control. -
Page 13: Installation Notes
KP-32 Installation Notes Refer to the KP-12 User Manual (p/n 9350-7497-001) for complete user information. KP-32 Installation Notes Use either FRAME connector (but not both) on the back of the keypanel to connect to an intercom port at a Station Breakout Panel. -
Page 14: Connections
Intercom Port Connections Connections INTERCOM- Use either of the “To Matrix” connectors (but not both) to connect to an intercom port. The intercom port that you connect to will determine the address of the unit. An LED labeled “Data’ is located next to the Matrix connectors and serves as a basic indicator. -
Page 15: Installing The Cdp-950
CDP-950 Camera Delegate Panel Installation Notes Installing the CDP-950 Before installing the CDP-950, remove the top cover and set the internal DIP Switches: DIP #1 Normal/ISO Select Closed: Normal Operation Open: ISO Operation DIP #2 Baud Rate Select Closed: 9600 baud Open: 76,800 baud (Do not use for ADAM) DIP #3... - Page 16 Intercom Port Connections ADAM Master Controller Card (MC-ADAM 9002-7514-100) DIP Switch Settings (S1) TABLE 1. Description Default Setting On=Closed, Off=Open On=Closed, Off=Open Switch No. AZedit baud rate select OFF: 9600 ON: 38.4 Key Incoming Message Option OFF: Normal Operation ON: All callers displayed in Incoming Messages window Keypanel “busy”...
- Page 17 MCII-e Factory set DIP Switch Settings TABLE 2. DIP Switch 1 Debug Only! Must be in OPEN position. Sets the baud rate for AZedit serial connection via J1. By default, AZedit is set for COM1 and 38,400 kbps (38.4k). The baud rate set in AZedit must match the baud rate setting of the Master Controllers in ADAM.
- Page 18 Intercom Port Connections Address DIP Switch Settings for KP-95, 96, 97, 98 Keypanels and the TIF TABLE 4. Address DIP Switch Setting Logical Keypanel Number DOWN DOWN DOWN DOWN DOWN DOWN DOWN DOWN DOWN DOWN DOWN DOWN DOWN DOWN DOWN DOWN DOWN NOTE: The shaded area is for CS9xxx system address only!
-
Page 19: Kp-32 Addressing
KP-32 Addressing KP-32 Addressing A rotary switch is used to indicate the logical port address the keypanel is to use when communicating with the Matrix. The switch is read continuously through polling by the matrix. If the port address is changed, the new address is effective immediately. - Page 20 Intercom Port Connections UIO-256 Relay Outputs Connector (J5) TABLE 8. Relay Output Numbers NC Contact Common NO Contact 1/17/33/49 2/18/34/50 3/19/35/51 4/20/36/52 5/21/37/53 6/22/38/54 7/23/39/55 8/24/40/56 9/25/41/57 10/26/42/58 11/27/43/59 12/28/44/60 13/29/45/61 14/30/46/62 15/31/47/63 16/32/48/64 a. Dependent on UIO-256 DIP Switch SW1 Settings for Input/Output Range as summarized in Table 7. The relay contacts are rated for 0.5A at 120 VAC;...
- Page 21 KP-32 Addressing a. Dependent on UIO-256 DIP Switch SW1 Settings for Input/Output Range as summarized in Table 7. Inputs will sink 100mA max at a maximum input voltage of +18 VDC For operation from an external DC voltage source, connect the external control voltage to the “+” pin, and connect the external common to the “- ”...
- Page 22 Intercom Port Connections Intercom System Planning Worksheet TABLE 10. ADAM Logical Intercom Audio I/O Keypanel AZedit AZedit Description Port No. Card No. Number Alpha Alias (Device Type, Location, User, etc.)
- Page 23 KP-32 Addressing Intercom System Planning Worksheet TABLE 10. ADAM Logical Intercom Audio I/O Keypanel AZedit AZedit Description Port No. Card No. Number Alpha Alias (Device Type, Location, User, etc.)
- Page 24 Intercom Port Connections Intercom System Planning Worksheet TABLE 10. ADAM Logical Intercom Audio I/O Keypanel AZedit AZedit Description Port No. Card No. Number Alpha Alias (Device Type, Location, User, etc.)
-
Page 25: Chapter 3 - Device Connections
CHAPTER 3 Device Connections Connections to the ADAM Frame An ADAM Intercom System can be setup in a variety of configurations to meet different user requirements. Several common variations are illustrated in the system drawings starting on page 33. Configuration Computer Connection and Check Use an RS-232 serial cable to connect from J1 of the XCP-ADAM-MC Breakout Panel to COM1 or COM2 of the configuration PC. -
Page 26: Connecting A Single Pap
Device Connections PAP Addresses TABLE 11. IFB Range Default Ports for Panel No. Model Program Input (Default = 1) Low (Default) High PAP-940 1-24 1-40 41-80 PAP-950-50 1-50 1-50 51-100 PAP-951 1-12 13-24 PAP-952 1-16 1-24 25-48 The intercom port addresses for program input, as well as the low and high ranges for IFB output, are stored in EPROM memory in the PAP. -
Page 27: Pap-32 Program Assign Panel
Connections to the ADAM Frame PAP-32 Program Assign Panel The PAP-32 connects to J3 on the ADAM system, port 902 on an ADAM CS system. The baud rate, as will all UIO-256, PAP, and LCP-102 devices is fixed at 76.8k baud. A cable must be made to connect the PAP-32 to the system. -
Page 28: Viewing The Program Source For An Ifb
Device Connections Viewing the Program Source for an IFB Press an IFB destination key which has an IFB assignment (i.e., is not blank/). The IFB key’s lower LED will be turned on solid red. If the specified IFB has a program source, the lower LED for the key which has that program source assigned will turn on solid red for as long as the IFB key is held on. -
Page 29: Uio-256 Input/Output Frame
UIO-256 Input/Output Frame UIO-256 Input/Output Frame Connecting a single UIO-256 Frame Connect a single UIO-256 to J3 of the Master Controller Breakout Panel, as shown in ADAM-101 through ADAM-108 interconnect diagrams starting on page X. Use a RS-485 data cable wired as shown in the ADAM -809 installation drawing on page 53. -
Page 30: Connecting To The Ssa-324
Device Connections Connecting to the SSA-324 General Description The SSA-324 is a System-to-System Adapter (or interface). It interconnects the voice signals between different types of intercom systems. In addition, it can optionally interconnect intercom systems. Also, it can optionally interconnect “Calls” or tally signals between systems. -
Page 31: Tb1 Four Wire Connections
Connecting to the SSA-324 TB1 Four Wire Connections System A System B TB1- TB1- Audio In Hi Audio In Lo Audio Out Hi Audio Out Lo J104 Power Input Earth 16VAC 16VAC No Conn. J103 I/O Earth 4-wire Audio In Hi, System A 4-wire Audio In Lo, System A 4-wire Audio Out Hi, System A 4-wire Audio Out Lo, System A... -
Page 32: Front Panel Dyn. Mic Headset Connector
Device Connections Front Panel Dyn. Mic Headset Connector Mic Lo Mic Hi Headphone Com Headphone Hi Motherboard Test Signal Jumper Place jumper on W2 for tone test signal, W3 for voice test signal. Test signal used with headset and front panel nulling adjustments to null return 2-wire signal. -
Page 33: Rear Panel
Connecting to the SSA-324 Rear Panel Switches Unbalance (Out) Balance (In) / Select Two-wire, System A Unbalance (Out) Balance (In) / Select Two-wire, System B Operation Nulling Preset Controls as follows: To/From RTS Set to Midway Duck Level Set to CW Set to Midway Set to Midway Set to CW... -
Page 34: Connecting To An Ssa-424
Device Connections Connecting to an SSA-424 General Description The SSA-424 Dual Digital Hybrid interfaces two, 2-wire intercom lines to two, 4-wire intercom lines. Unlike earlier analog hybrids, the SSA-424 features advanced digital signal processing to achieve automatic nulling of the 4-wire lines. Plus, each hybrid features convenient peak-reading level meters to quickly match the levels between the lines that are being interfaced. -
Page 35: 4-Wire Call Signal Connections
Connecting to an SSA-424 4-Wire Call Signal Connections NOTE: These connections will require the call signal option. Part Number 9002705500. Call Signal Connections for ADAM, ADAM CS, and Zeus You can use the General Purpose Interface (GPI) connector to interface the call signals. The pin-out of the connector is the same for all of these intercom systems. - Page 36 Device Connections...
-
Page 37: Chapter 4 -Drawings
CHAPTER 4 Drawings... - Page 38 Drawings...
-
Page 39: Adam-101 Adam Intercom System Xcp-40-Rj11 Interconnect Diagram
FIGURE 3. ADAM-101 ADAM Intercom System XCP-40-RJ11 Interconnect Diagram ADAM Installation Manual -... -
Page 40: Adam-102 Adam Intercom System Xcp-40-Db9 Interconnect Diagram
FIGURE 4. ADAM-102 ADAM Intercom System XCP-40-DB9 Interconnect Diagram ADAM Installation Manual -... -
Page 41: Adam-103 Adam Intercom System Xcp-955 / Jack Fields / Scsi Interconnect Diagram
FIGURE 5. ADAM-103 ADAM Intercom System XCP-955 / Jack fields / SCSI Interconnect Diagram ADAM Installation Manual -... -
Page 42: Adam-104 Adam Intercom System Xcp-955 / Jack Fields / Rj Interconnect Diagram
FIGURE 6. ADAM-104 ADAM Intercom System XCP-955 / Jack fields / RJ Interconnect Diagram ADAM Installation Manual -... -
Page 43: Adam-105 Adam Intercom System Xcp-955 / Jack Fields / Scsi Interconnect Diagram
FIGURE 7. ADAM-105 ADAM Intercom System XCP-955 / Jack fields / SCSI Interconnect Diagram ADAM Installation Manual -... -
Page 44: Adam-106 Adam Intercom System Xcp-955 / Jack Fields / Rj Interconnect Diagram
FIGURE 8. ADAM-106 ADAM Intercom System XCP-955 / Jack fields / RJ Interconnect Diagram ADAM Installation Manual -... -
Page 45: Adam-107 Adam Intercom System Xcp-954-48 / Jack Fields / Scsi Interconnect Diagram
FIGURE 9. ADAM-107 ADAM Intercom System XCP-954-48 / Jack fields / SCSI Interconnect Diagram ADAM Installation Manual -... -
Page 46: Adam-108 Adam Intercom System Xcp-954-48 / Jack Fields / Rj Interconnect Diagram
FIGURE 10. ADAM-108 ADAM Intercom System XCP-954-48 / Jack fields / RJ Interconnect Diagram ADAM Installation Manual -... -
Page 47: Adam-301 Adam Intercom System Matrix Frame Layout - Aio-8
FIGURE 11. ADAM-301 ADAM Intercom System Matrix Frame Layout - AIO-8 ADAM Installation Manual -... -
Page 48: Adam Intercom System Matrix Frame Layout - Aio-16
FIGURE 12. ADAM Intercom System Matrix Frame Layout - AIO-16 +2.1V +2.1V POWER POWER GOOD GOOD +15V +15V -15V -15V Ports 137 through 272 RESET RESET RESET RESET Ports 137 through 272 Ports 1 through 136 MCIIe MCIIe SYSTEM SYSTEM MCIIe MCIIe CONTROLLER... -
Page 49: Adam-801 Adam Intercom System Audio Input / Output / Data 50 Pins Scsi-2 Cable
FIGURE 13. ADAM-801 ADAM Intercom System Audio Input / Output / Data 50 Pins SCSI-2 Cable ADAM Installation Manual -... -
Page 50: Adam-802 Adam Intercom System Audio Input / Output 25 Pairs Telco Cable
FIGURE 14. ADAM-802 ADAM Intercom System Audio Input / Output 25 Pairs Telco Cable ADAM Installation Manual -... -
Page 51: Adam-803 Adam Intercom System Audio Input / Output 25 Pairs To Rj-45 Cable
FIGURE 15. ADAM-803 ADAM Intercom System Audio Input / Output 25 Pairs to RJ-45 Cable ADAM Installation Manual -... -
Page 52: Adam-804 Adam Intercom Matrix Rj11 To 50 Pins Telco Translation Cable
FIGURE 16. ADAM-804 ADAM Intercom Matrix RJ11 to 50 Pins Telco Translation Cable ADAM Installation Manual -... -
Page 53: Adam-805 Adam Intercom Matrix Db9 To 50 Pins Telco Translation Cable
FIGURE 17. ADAM-805 ADAM Intercom Matrix DB9 to 50 Pins Telco Translation Cable ADAM Installation Manual -... -
Page 54: Adam-806 Adam Intercom System Master Controller 68 Pins Scsi-2 Cable
FIGURE 18. ADAM-806 ADAM Intercom System Master Controller 68 Pins SCSI-2 Cable ADAM Installation Manual -... -
Page 55: Adam-807 Adam Intercom System Azedit To Pc Rs-232-C Cable
FIGURE 19. ADAM-807 ADAM Intercom System AZedit to PC RS-232-C Cable ADAM Installation Manual -... -
Page 56: Adam-808 Adam Intercom System Matrix To Trunk Aster Rs-485/ Rs232C Cable
FIGURE 20. ADAM-808 ADAM Intercom System Matrix to Trunk aster RS-485/ RS232C Cable ADAM Installation Manual -... -
Page 57: Adam-809 Adam Intercom System Uio-256 And Pap Cables
FIGURE 21. ADAM-809 ADAM Intercom System UIO-256 and PAP Cables ADAM Installation Manual -... -
Page 58: Intercom Station Cables
FIGURE 22. Intercom Station Cables CONTACTS RJ11 MOD PLUG 1 2 3 4 5 6 1 2 3 4 5 6 (VIEW FROM CABLE ENTRANCE) DE-9S (Female) DE-9S (Male) TO INTERCOM To Station Breakout Panel To Intercom Station TO TIF LATCH MATRIX DE-9P... -
Page 59: Adam-811 Adam Intercom System Cdp-950 Cables
FIGURE 23. ADAM-811 ADAM Intercom System CDP-950 Cables ADAM Installation Manual -...