Page 1
Single Ultrawide Monitor Extra Tall Desk Mount SKU: STAND-V100T Instruction Manual Assembly Video & Product Info www.vivo-us.com/products/stand-v100t...
Page 2
[ THIS PAGE HAS BEEN INTENTIONALLY LEFT BLANK ]...
Page 3
If you do not understand these directions, or if you have any doubts about the safety of the installation, please contact our product support team at 309-278-5303 or help@vivo-us.com for further assistance. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual.
Package Contents C (x1) A (x1) B (x1) Upper Pole Lower Pole D (x1) E (x1) F (x1) Clamp Support Plate Pole Cable Clip G (x1) H (x2) Clamp Cable Arm Cable Clip Clip Included Hardware & Tools M-A (x4) M-B (x4) M-C (x4) M4x12mm...
ASSEMBLY STEPS STEP 1 Assembly Option #1: Desk Clamp Using the 6mm Allen Wrench (T-B), loosen the Screw located inside the Clamp (D), lowering the Clamp Bracket, creating a space larger than the thickness of your desktop. Clamp Bracket Slide the Clamp (D) onto your desktop in your desired position.
Page 6
Assembly Option #2: Grommet Installation Screw Clamp Bracket Use 6mm Allen Wrench (T-B) to remove the Screw and Clamp Bracket located inside the Clamp (D). Both pieces can be discarded and will not be used in the remainder of the assembly.
Page 7
STEP 2 Slide the Lower Pole (B) over the Post on Clamp (D). Tighten the Set Screw on the Lower Pole using the 3mm Allen Wrench (T-A) to secure. Post Screw...
Page 8
Cont’d Slide one Pole Cable Clip (F) over Lower Pole, and then thread the Upper Pole (A) onto the Lower Pole. Tighten the set screw on Lower Pole using the 3mm Allen Wrench (T-A).
Page 9
STEP 3 Unfold the Arm (C) straight, as shown below. Slide the Arm Cable Clip (H) and Arm (C) onto the Pole (A). Hold Arm at the desired height and secure using the 6mm Allen Wrench (T-B). Snap Arm Cable Clips (H) onto both segments of the Arm.
Page 10
STEP 4 Loosen the Thumbscrew (C2) on the back of VESA Bracket (C1), then separate and remove VESA Plate (C3) by pulling out and sliding upwards. Install the VESA Plate (C3) onto the back of your monitor using M4x12mm Screws (M-A) or M5x12mm Screws (M-B) and M5 Washers (M-C), orienting the arrow on the VESA Plate pointing up.
Page 11
STEP 5 Adjusting the Tilt Joint Adjustment Screw Loosen Tilt Joint: Set Angle Use 6mm Allen Wrench (T-B) to Firmly grip the VESA Bracket and loosen the Tilt Joint Adjustment adjust to your desired viewing Screw, located on the side of angle, and hold in place.
Page 12
STEP 6 With the assistance of a second person, line up the VESA Plate (C3) on your monitor with the VESA Bracket and the Plate Hooks into the pockets of the VESA Bracket (C1). Monitor & VESA Bracket may need to be angled backwards slightly when sliding on. 2 Person Mounting is Recommended *Monitor &...
Page 13
Fine Tune Tilt Angle If the monitor is angled further than intended... Heavy Weighted/ Ultrawide Monitors [ 22lbs - 44lbs ] Firmly Hold Monitor Firmly grasp and hold the monitor in place. Do NOT release monitor until you have completed steps below. Loosen Tilt Joint: With a hand still on the monitor, use 6mm Allen Wrench (T-B) to loosen the...
Page 14
STEP 7 Make adjustments as desired on swivel and orientation. *If you are using the stand with the clamp, do NOT extend the arm past the back of the clamp to prevent possible damage to your monitor and stand.
Page 15
STEP 8 Route cables through the Arm Cable Clips (H) and Pole Cable Clip (F). Install the Clamp Cable Clip (G) onto Clamp (D) by placing it inside the top of the channel and sliding down.
LAST UPDATED: 04/2/24 REV1 v1.0 Need Help? Get In Touch Monday-Friday from 7:00am-7:00pm CST help@vivo-us.com www.vivo-us.com 309-278-5303 Chat live with an agent! FOR MORE GREAT VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: WWW.VIVO-US.COM VIVO-us @vivo_us...
Need help?
Do you have a question about the STAND-V100T and is the answer not in the manual?
Questions and answers