Table of Contents
Advertisement
Quick Links
Mechanical Arm Single Ultrawide Monitor
Desk Mount
Instruction Manual
SKU: STAND-V100E
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
https://vivo-us.com/products/stand-v100e
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
help@vivo-us.com
www.vivo-us.com
Chat live with an agent!
309-278-5303
Advertisement
Table of Contents
Related Manuals for Vivo STAND-V100E
Summary of Contents for Vivo STAND-V100E
- Page 1 Mechanical Arm Single Ultrawide Monitor Desk Mount Instruction Manual SKU: STAND-V100E Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product. https://vivo-us.com/products/stand-v100e GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST help@vivo-us.com...
- Page 2 WARNING! If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual.
- Page 3 ASSEMBLY STEPS STEP 1 OPTION A: Clamp Installation Attach Clamp Brace (F) to Base (A) using M6x12mm Screws (S-B) and tighten with 4mm Allen Wrench (T-A). Thread M10x63mm Screws (S-D) into Clamp (G) and place Clamp Plate (E) on top. Loosen bolts on back of Clamp (G) using 4mm Allen Wrench (T-A), leaving 6mm of thread exposed.
- Page 4 STEP 1 (Continued) OPTION B: Grommet Base Installation Mark drill holes using the larger outer holes on Clamp Plate (E), drill two 3/8” (10mm) holes. Insert M10x63mm Screws (S-D) with Clamp Plate (E) up through the underside of the desk and tighten to Base (A) using the 6mm Allen Wrench (T-B).
- Page 5 STEP 4 Attach VESA Adapter (D) using M8x35mm Screws (S-C) and M8 Nuts (S-A) on Spring Arm (C) using 6mm Allen Wrench (T-B). Unscrew Thumbscrew (D1) on VESA Adapter (D) and remove VESA Plate (D2). STEP 5 Install the VESA Plate (D2) to monitor using M4x12mm Screws (M-A) or M5x12mm Screws (M-B) with M5 Washers (M-C), making sure the arrow in back is pointing up.
- Page 6 STEP 7 If needed, adjust Spring Arms (C) to support the monitors using the 6mm Allen wrench (T-B). Turn the screw in back counter-clockwise to decrease support, and clockwise to increase. STEP 8 Remove cable cover on Spring Arm (C) by pulling the sides away from the arm to unclip them. Slide cable cover on Lower Arm (B) forward to remove it.
- Page 7 Adjust as Desired Adjust tilt and swivel using 6mm Allen Wrench (T-B). For safety, please do not extend the monitor behind the desk. This may cause instability and tip the desk over.
- Page 8 : 1HR 8M (within office hrs) - 23% within < 15m - 38% within < 30m - 61% within < 1hr - 83% within < 2hr - 92% within < 3hr FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com...
Need help?
Do you have a question about the STAND-V100E and is the answer not in the manual?
Questions and answers