Advertisement
Quick Links
Pack 11
B U I L D
I N S T R U C T I O N S
STAGE 86: FIT TING THE RIGHT DOOR HANDLE
STAGE 90: FITTING THE WINDSCREEN
STAGE 87: FIT TING THE RIGHT DOOR HINGE
STAGE 91: FIT TING THE SPLIT REAR WINDOW
STAGE 88: DETAILING THE RIGHT DOOR
STAGE 92: PREPARING THE ROOF LINER
INTERIOR PANEL
STAGE 89: ASSEMBLING THE RIGHT WINDOW
AND DOOR
General Motors Trademarks used under license by Premium & Collectibles Trading Co. Ltd on behalf of Agora Models.
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Agora Models Corvette Sting Ray Pack 11
Summary of Contents for Agora Models Corvette Sting Ray Pack 11
- Page 1 STAGE 88: DETAILING THE RIGHT DOOR STAGE 92: PREPARING THE ROOF LINER INTERIOR PANEL STAGE 89: ASSEMBLING THE RIGHT WINDOW AND DOOR General Motors Trademarks used under license by Premium & Collectibles Trading Co. Ltd on behalf of Agora Models.
- Page 2 Advice from the experts Spare screws are included with each part. Occasionally, you may be instructed to keep spare or unused screws for a later stage. Keep these spares in a safe place and label them correctly. Please make sure you don’t mix up the screws. They look quite similar, but the threads do vary slightly.
- Page 3 Stage 86: Fitting the Right Door Handle You’ll now begin building the right door in the same way as before, starting by fitting the handle. S T A G E 8 6 P A R T S L I S T Name Right door Right door handle...
- Page 4 Stage 86: Fitting the Right Door Handle Align the right door handle with the right door as shown. Fit the handle in place. Secure from the other side with an FM screw. AGORAMODELS CORVETTE STING RAY...
- Page 5 Stage 86: Fitting the Right Door Handle S T A G E C O M P L E T E AGORAMODELS CORVETTE STING RAY...
- Page 6 Stage 87: Fitting the Right Door Hinge In this stage you’ll fit the right door hinge mount and secure it using the hinge plate. The right door inside panel can be kept safely until it is needed in the next stage. S T A G E 8 7 P A R T S L I S T Name Right door inside panel...
- Page 7 Stage 87: Fitting the Right Door Hinge Align the door hinge mount with the right door (stage 86). Place the hinge mount in position, then align the door hinge Make sure the mount is oriented as shown (inset). plate as shown. Secure the hinge plate using 2x VM screws.
- Page 8 Stage 87: Fitting the Right Door Hinge S T A G E C O M P L E T E AGORAMODELS CORVETTE STING RAY...
- Page 9 Stage 88: Detailing the Right Door Interior Panel In this stage you’ll add details to the right door interior panel then fit it to the inside panel from stage 87. S T A G E 8 8 P A R T S L I S T Name Name Right door interior panel...
- Page 10 Stage 88: Detailing the Right Door Interior Panel Take the handrest cover and press it into the handrest. The Align the handrest with the interior panel as shown, then fit pins and holes are different sizes to ensure the correct fit. in place.
- Page 11 Stage 88: Detailing the Right Door Interior Panel Fit the other reflector knob in the same way. Secure from the other side using 2x AP screws. Align the interior panel with the right door inside panel from Fit the interior panel in place by pushing the screw columns stage 87.
- Page 12 Stage 88: Detailing the Right Door Interior Panel Turn the assembly over and secure with 2x AP screws. Take the smaller vent window crank (circled) and fit it into the shaped hole. The small vent window crank should look like this. Secure from the reverse side with a BP screw.
- Page 13 Stage 88: Detailing the Right Door Interior Panel Fit the larger window crank into the hole as shown. This part will turn to raise or lower the window so can be fitted in any orientation. From the reverse side, fit the small window gear onto the Secure with a PP screw.
- Page 14 Stage 88: Detailing the Right Door Interior Panel Align the interior panel trim as shown. Press the trim into the panel. Fit the door lock knob into the hole as shown. AGORAMODELS CORVETTE STING RAY...
- Page 15 Stage 88: Detailing the Right Door Interior Panel S T A G E C O M P L E T E AGORAMODELS CORVETTE STING RAY...
- Page 16 Stage 89: Assembling the Right Window and Door In this stage you’ll assemble the mechanism for working the right window then attach the two parts of the door together. S T A G E 8 9 P A R T S L I S T Name Name Right window...
- Page 17 Stage 89: Assembling the Right Window and Door Align the right window with the raised screw hole on the gear Fit the window onto the gear arm and secure using a TP arm. screw. The arm should be able to move in the channel. Take the interior panel assembly (stage 88) and fit the large Check that the teeth and the gears are engaged, then turn window gear in place.
- Page 18 Stage 89: Assembling the Right Window and Door Take the right window and align it with the assembly as Fit the window in place. shown. The channels on the window fit over the ridges on the panel. Press the smaller holes on the gear arm over the pins on the Secure in place with a TP screw.
- Page 19 Stage 89: Assembling the Right Window and Door Fit the spring onto the lock pin. Take the door assembly (stage 87) and align the lock pin bushing with it as shown. Make sure the bushing is oriented the correct way round (inset). Fit the bushing in place.
- Page 20 Stage 89: Assembling the Right Window and Door The lock pin should look like this once in place. Secure the bushing with an FM screw. Set the door assembly to one side and take the interior panel Fit the right quarter vent window in place. Make sure the pins assembly.
- Page 21 Stage 89: Assembling the Right Window and Door Take the door assembly and note the fixing points for the two parts. The windows are loose so it is easier to fit the door onto the panel. Fit the parts together, making sure the quarter vent window pins stay in position (see step 16).
- Page 22 Stage 89: Assembling the Right Window and Door Use 3x DM screws to secure the parts together. Use 2x WM screws to secure the top part of the door. Test the function of the window by turning the window crank. Peel the backing paper from the right door carpet trim (inset) then carefully stick the corner into the recess on the interior panel.
- Page 23 Stage 89: Assembling the Right Window and Door Press the carpet trim in place, using the recess to align it. Drive an FM screw into the hole located near to the lock pin. Take the right door chrome trim and align it with the section next to the quarter vent window as shown. Press the trim into the two holes firmly.
- Page 24 Stage 89: Assembling the Right Window and Door S T A G E C O M P L E T E AGORAMODELS CORVETTE STING RAY...
- Page 25 Stage 90: Fitting the Windscreen In this stage you’ll fit the windscreen frame and glass to the main body. S T A G E 9 0 P A R T S L I S T Name Windscreen frame Windscreen glass UP screw x3 VP screw x3 Windscreen frame...
- Page 26 Stage 90: Fitting the Windscreen Align the windscreen glass and frame as shown. Note the eight connection points on each of the parts. Fit the two parts together. AGORAMODELS CORVETTE STING RAY...
- Page 27 Stage 90: Fitting the Windscreen Align the windscreen frame with the main body (stage 85) as shown. Fit the windscreen frame into the four tabs (arrows) and four screw holes (circled) on the main body. Turn the assembly over and drive 2x UP screws into the frame. Take care not to let the screwdriver slip and scratch the windscreen.
- Page 28 Stage 90: Fitting the Windscreen Secure the corners of the frame with 2x VP screws. S T A G E C O M P L E T E AGORAMODELS CORVETTE STING RAY...
- Page 29 Stage 91: Fitting the Split Rear Window In this stage you’ll fit one of the most iconic features of the 1963 Corvette Sting Ray, the split rear screen window. S T A G E 9 1 P A R T S L I S T Name Rear left window glass Rear right window glass...
- Page 30 Stage 91: Fitting the Split Rear Window Align the left rear window glass and frame as shown. Fit the glass into the frame, starting with the corners on the diagonal side (arrows). Once the corners are in place, push the holes over the corresponding pins (circled). Fit the right rear window glass and frame together in the same way.
- Page 31 Stage 91: Fitting the Split Rear Window Align the rear left and right windows with the main body as shown. Fit the frames in place, making sure to start by pressing the pins into the holes on the outer edge (circled). S T A G E C O M P L E T E AGORAMODELS CORVETTE STING RAY...
- Page 32 Stage 92: Preparing the Roof Liner In this stage you’ll prepare the roof liner by fitting the interior light and securing its LED. S T A G E 9 2 P A R T S L I S T Name Roof liner Interior light glass Interior light frame...
- Page 33 Stage 92: Preparing the Roof Liner Take the interior light glass and frame. The pin and hole Fit the frame onto the glass. Note that the pin protrudes ensure the parts fit together in the correct way. slightly from the frame. The pin fits into the small hole (circled) on the roof liner to ensure the correct alignment.
- Page 34 Stage 92: Preparing the Roof Liner Fit the interior light in place. Turn the assembly over and secure with 2x WP screws. Retrieve the main assembly and locate the interior light LED cable (marked ‘A4’). Disconnect the cable. AGORAMODELS CORVETTE STING RAY...
- Page 35 Stage 92: Preparing the Roof Liner Align the bulb with the hole in the roof liner. Orient the wires Fit the bulb into the hole, then bend the wires carefully and towards the channel (circled). run them through the channel as shown. Secure the wire in the channel using the adhesive tape.
- Page 36 Stage 92: Preparing the Roof Liner S T A G E C O M P L E T E AGORAMODELS CORVETTE STING RAY...
Need help?
Do you have a question about the Corvette Sting Ray Pack 11 and is the answer not in the manual?
Questions and answers