Aiwa NSX-MT725 Operating Instructions Manual page 21

..'?W ~' :'"2$ .!'.'"J"': '. J~:"2 ':' ,% ~ '~: L :' s",:"%"'.''.',"'
RANDti"M/REgPEATPLAY'"' "'
Use the remote control.
RANDOM play
All the tracks on the selected disc or all the discs can be played
randomly.
REPEAT play
A single disc or all the discs can be played repeatedly.
Press RANDOM/REPEAT.
Each time it is pressed, the function can be selected cyclically.
RANDC)M play — RANDOM lights up on the display.
REPEAT play — G lights upon the display.
RANDC)M/REPEAT play — RANDOM and G light upon the
display.
Cancel — RANDOM and G disappear from the display.
To ~lav all discs, press +> to start play.
To plav a sinale disc, press one of DISC DIRECT PLAY 1-3 to
start play.
m
During random play it is not possible to skip to the previously
played track with +.
: :..: 7" ; ":-:. : -:":-=" :,:,:% %..2-:,'$ ": . :,1":$! >%%%""..&"27 :-"..,,.', -. ~ %",,"=2.:,:...,4t~4,&,& ,%-., ..". ,,,, Xe.,r.~.:r .!
B'LANi
SKIP PLAY
The silent portions between tracks recorded on a CD can be
skipped during playback,
1
2
Press CD BLANK SKIP.
"CD BLANK SKIP ON" is displayed and a small dot appears
in the display.
Small dot
t
Press +> to start playback.
The silent portions betwee; tracks will be skipped, and the
sound will be played back without interruption. If a track fades
out (ends with the sound gradually decreasing), the fadeout
portion also will be skipped.
To return to normal playback
Press CD BLANK SKIP again, and "CD BLANK SKIP OFF is
displayed and the dot in the display disappears.
There may be a case where BLANK SKIP PLAY does not
function correctly.
BLANK SKIP PLAY is automatically canceled when performing
Al EDIT RECORDING (page 24), PROGRAMMED EDIT
RECORDING (page 25), or recording during PROGRAMMED
PLAY (page 21) or RANDOM PLAY (page 21).
Up to 30 tracks can be programmed from any of the inserted
discs.
a
1
2
2
5
44,W
Use the remote control.
1
2
3
4
Press PRGM twice in stop mode.
"PRGM" is displayed
PRGM
When PRGM is pressed once in step 1, the unit enters the
KARAOKE PROGRAM (page 29).
Press DISC DIRECT PLAY, then press numbered
buttons 1-3 within 3 seconds to select a disc.
Go to the next step when the tray stops rotating.
Press numbered buttons O-9 and +1 Oto program
a track.
Example:
To select the 25th track, press +10, +10 and 5.
To select the 10th track, press +1O and O.
Selected track number
Program number
Total number of selected tracks
Total playing time of
the selected tracks
Repeat steps 2 and 3 to program other track:;.
5 Press 4> to start play.
To check the program
Each time ++ or - is pressed in stop mode, a disc number,
track number, and program number will be displayed.
To
clear the program
Press CLEAR in stop mode.
To add tracks to the program
Repeat steps 2 and 3 in stop mode. The track will be programmed
after the last track.
To change the programmed tracks
Clear the program and repeat all the steps again.
To
play the programmed tracks repeatedly
After programming the tracks, press RANDOIWREPEAT
repeatedly until CL appears cm the display.
During programmed play, you cannot perform ralndom Iplay,
check the remaining time, and select a disc or track. "CAN'T
USE" is displayed if you attempt to select a track.
"FULL' is displayed if you attempt to program more than 30
tracks.
ENGLISH
21