ELCOM REQ5 Y Series Operating And Assembly Instruction Manual page 4

Address call push-button automatically
The call push-button and connector on the back
are addressed by the automatic call push-button
addressing as follows. The addressing takes place
starting from the top downwards, and with a two-
rowed door station, counterclockwise automatically
upwards to the right (figure 11).
i
Door stations are automatically pre-configured
at the factory.
The menu entry is selected.
nately with the entry for cancel.
„ With / select the entry
addressing.
„ Confirm with .
During the addressing, the display flickers.
Afterwards the display returns to the previous
menu entry .
0/0
0/0
0/1
0/1
0/2
0/3
0/4
0/5
0/2
0/6
0/7
Figure 11: Module address and automatic call
push-button addressing
Set individual call push-button address/function
The menu entry Set individual call push-button
address/function is selected and flashes.
„ Confirm the call push-button to be set.
The menu entry flashes alternately with the
current address/function.
„ With / select the required address
or function for light push-button,
door release push-button or
„ Confirm set address/function with
The device applies the setting and returns to
the previous menu entry.
4 Elcom Kommunikation GmbH - Gottfried-Leibniz-Str.1 - D-74172 Neckarsulm - www.elcom.de -
Display saved error codes
Video insert and call-button module errors that
occur during operation are stored in the the error
memory of the video insert for diagnosis.
„ Select menu entry
confirm with
If no error code exists
seconds and afterwards
If error codes are saved
flashes alter-
the module address and the error code.
„ Press button
for automatic
codes if necessary.
„ Press button
Error
code
0/F
0/E
0/4
0/D
0/C
0/B
0/A
0/3
0/9
0/8
Table 2: Error codes and counter actions
i
The memory should only be deleted once 5
error codes have been stored, so that new error
codes can be saved.
i
Identical error codes are only saved once.
Inserting door station
...
The system settings are complete.
for
„ Remove opening tool from housing.
for no function.
„ Insert door station and press down until it clicks
.
audibly into place simultaneously at the top and
bottom if possible (Figure 12).
.
with button
is displayed for 2
.
flashes followed by
/ , to call up further error
to return to menu entry
Error cause Counter actions
Communication error If the error per-
between camera in- sists, the call
sert and call push-but- push-button
ton module. Once the module must be
error has occurred 3 replaced.
times, the system is
reset automatically
and the error code is
generated.
sticking call button Check call
push-button
module, and if
there is a defect,
replace and
address.
Writing of the call If the error per-
push-button address sists, the call
in the call push-button push-button
module fails. module must be
replaced and
addressed.
Figure 12: Insert door station
Align camera
The camera can be aligned in order to adapt the
camera picture to the local circumstances (Figure
14 and 15).
The door station is installed.
/ and
„ Loosen the locating screw for the camera
1.5 mm with the Allen key supplied (Figure 13).
„ Call an indoor station video from the door sta-
tion by call push-button.
.
Figure 13: Alignment of the camera
„ Align camera (figure 14/15).
The entrance area is clearly visible on the
display of the indoor station.
„ Fix camera again with screw (4).
1 2 m
2 m
1
0
1
2
Figure 14: Vertical camera orientation
2 1 0
2
1
Figure 15: Horizontal camera orientation
(4)
vertical
aperture angle
vertical
swivelling range
1 2 m
horizontal ap-
erture angle
horizontal
swivelling range
6LE000714A - 06/2015