Related Manuals for Avigilon NVR6-AINVR2-FORM-D-10GBASET
Summary of Contents for Avigilon NVR6-AINVR2-FORM-D-10GBASET
- Page 1 Avigilon 10G Base-T Kit Installation Guide Installation Guide NVR6-AINVR2-FORM-D-10GBASET NVR6 Standard Form D NVR6 Premium Form D AI NVR 2 Standard Form D AI NVR 2 Premium Form D...
- Page 2 Avigilon Corporation nor any of its affiliated companies: (1) guarantees the completeness or accuracy of the information contained in this document; or (2) is responsible for your use of, or reliance on, the information. Avigilon Corporation shall not be responsible for any losses or damages (including consequential damages) caused by reliance on the information presented herein.
- Page 3 Contents Introduction Confirm Package Contents Recommended Tools Installing the NIC Opening the Cover Locating the Slot Installing the NIC in Slot 2 Installing the NIC in Slot 5 Removing the Expansion Card Riser Installing the NIC into the Expansion Card Riser Installing the Expansion Card Riser Reattaching the Cover Confirming the Installation...
- Page 4 Introduction Avigilon provides an optional 10G Base-T Kit for the NVR6 and AI NVR 2 Standard Form D and Premium Premium Form D. This kit provides you with high-speed Ethernet ports for faster connections to your security network of ACC Servers and Clients.
- Page 5 Installing the NIC NOTE If the NVR is an operating part of your security system, be aware that it must be shut down to complete this procedure. Before installing the NIC: 1. Turn off the NVR, including all attached peripherals. Press the power button on the front panel, and wait for the light to stop blinking to indicate shutdown is complete.
- Page 6 Opening the Cover 1. At the top of the NVR, unlock the latch release then lift and rotate the latch towards the back of the unit. The cover slides back and is released from the body. Use a Phillips #2 screwdriver to remove the shipping screws before unlatching the cover if you are removing the cover of an NVR for the first time.
- Page 7 Locating the Slot Based on the model of your NVR, identify the correct slot to install the card in: NVR6 Standard - PCIe Slot 2 NVR6 Premium - PCIe Slot 5 AI NVR 2 Standard - PCIe Slot 2 AI NVR 2 Premium - PCIe Slot 5 Follow the instructions in the respective sections below for your model.
- Page 8 1. Disconnect all the riser cables from the system board. 2. For the appropriate expansion card riser, loosen the two thumb screws with a Phillips #2 screwdriver. 3. Remove the expansion card riser. Installing the NIC into the Expansion Card Riser 1.
- Page 9 Installing the Expansion Card Riser 1. Reconnect all the riser cables to the system board. 2. Insert the expansion card riser into the system board and fasten the expansion card riser thumb screws. Installing the Expansion Card Riser...
- Page 10 Installing the Expansion Card Riser...
- Page 11 Reattaching the Cover When all the components of the kit have been installed: 1. Ensure all expansion card latches are closed and there are filler covers for all empty slots. 2. Reinstall the air shroud. 3. Close and lock the NVR access panel. 4.
- Page 12 Under the Network Adapters heading, there should be two new ports available in the respective slot. These new ports should have a Link Speed of 10Gbps. Limited Warranty Avigilon warranty terms for this product are provided at avigilon.com/warranty. Confirming the Installation...
- Page 13 For More Information For additional product documentation and software and firmware upgrades, visit support.avigilon.com. Technical Support Contact Avigilon Technical Support at support.avigilon.com/s/contactsupport. Additional Documentation AI NVR 2 User Guides NVR6 User Guides For More Information...
Need help?
Do you have a question about the NVR6-AINVR2-FORM-D-10GBASET and is the answer not in the manual?
Questions and answers