Subscribe to Our Youtube Channel
Related Manuals for Avigilon NVR6-AINVR2-FORM-D-10GBE
Summary of Contents for Avigilon NVR6-AINVR2-FORM-D-10GBE
- Page 1 Avigilon 10GbE Kit Installation Guide Installation Guide NVR6-AINVR2-FORM-D-10GBE NVR6 Standard Form D NVR6 Premium Form D AI NVR 2 Standard Form D AI NVR 2 Premium Form D...
- Page 2 Avigilon Corporation nor any of its affiliated companies: (1) guarantees the completeness or accuracy of the information contained in this document; or (2) is responsible for your use of, or reliance on, the information. Avigilon Corporation shall not be responsible for any losses or damages (including consequential damages) caused by reliance on the information presented herein.
-
Page 3: Table Of Contents
Contents Introduction Confirm Package Contents Recommended Tools Installing the NIC Opening the Cover Locating the Slot Installing the NIC in Slot 2 Installing the NIC in Slot 5 Removing the Expansion Card Riser Installing the NIC into the Expansion Card Riser Installing the Expansion Card Riser Reattaching the Cover Confirming the Installation... -
Page 4: Introduction
Introduction Avigilon provides an optional 10GbE Upgrade Kit for the NVR6 and AI NVR 2 Standard Form D and Premium Form D. This kit provides you with high-speed Ethernet ports for faster connections to your security network of ACC Servers and Clients. -
Page 5: Confirm Package Contents
Confirm Package Contents Confirm that the kit you are installing contains the following components: 1 × 2-port 10GbE PCIe card Confirm Package Contents... -
Page 6: Recommended Tools
Recommended Tools The following tools are not included in the kit package, but are needed to complete the installation: Phillips #2 screwdriver Torx #T30 screwdriver Wrist-grounding strap connected to the ground ESD Mat IMPORTANT It is recommended that you always use an antistatic mat and antistatic strap while working on components inside the system. -
Page 7: Installing The Nic
Installing the NIC NOTE If the NVR is an operating part of your security system, be aware that it must be shut down to complete this procedure. Before installing the NIC: 1. Turn off the NVR, including all attached peripherals. Press the power button on the front panel, and wait for the light to stop blinking to indicate shutdown is complete. -
Page 8: Opening The Cover
Opening the Cover 1. At the top of the NVR, unlock the latch release then lift and rotate the latch towards the back of the unit. The cover slides back and is released from the body. Use a Phillips #2 screwdriver to remove the shipping screws before unlatching the cover if you are removing the cover of an NVR for the first time. -
Page 9: Locating The Slot
Locating the Slot Based on the model of your NVR, identify the correct slot to install the NIC in: NVR6 Standard - PCIe Slot 2 NVR6 Premium - PCIe Slot 5 AI NVR 2 Standard - PCIe Slot 2 AI NVR 2 Premium - PCIe Slot 5 Follow the instructions in the respective sections below for your model. -
Page 10: Installing The Nic In Slot 2
Installing the NIC in Slot 2 Follow the instructions in this section to install the NIC in slot 2 for the following NVR models: NVR6 Standard AI NVR 2 Standard With the NVR open: 1. Locate PCIe slot 2 on the system board. iDRAC 2. -
Page 11: Removing The Expansion Card Riser
Installing the NIC in Slot 5 Follow the instructions in this section to install the NIC in slot 5 on expansion card riser 2 for NVR6 Premium and AI NVR 2 Premium Form D. Removing the Expansion Card Riser With the NVR open: 1. -
Page 12: Installing The Nic Into The Expansion Card Riser
Installing the NIC into the Expansion Card Riser 1. Unpack the NIC. 2. To open the expansion card riser, pull the expansion card retention latch. 3. Insert the NIC into the slot of the expansion card riser. Press firmly until fully seated. 4. -
Page 13: Installing The Expansion Card Riser
Installing the Expansion Card Riser 1. Reconnect all the riser cables to the system board. 2. Insert the expansion card riser into the system board and fasten the expansion card riser thumb screws. Installing the Expansion Card Riser... - Page 14 Installing the Expansion Card Riser...
-
Page 15: Reattaching The Cover
Reattaching the Cover When all the components of the kit have been installed: 1. Ensure all expansion card latches are closed and there are filler covers for all empty slots. 2. Reinstall the air shroud. 3. Close and lock the NVR access panel. 4. -
Page 16: Confirming The Installation
Under the Network Adapters heading, there should be two new ports installed in the respective slot (slot 2 or 6, depending on your model). These new ports should have a Link Speed of 10Gbps. Limited Warranty Avigilon warranty terms for this product are provided at avigilon.com/warranty. Confirming the Installation... -
Page 17: For More Information
For More Information For additional product documentation and software and firmware upgrades, visit support.avigilon.com. Technical Support Contact Avigilon Technical Support at support.avigilon.com/s/contactsupport. For More Information...
Need help?
Do you have a question about the NVR6-AINVR2-FORM-D-10GBE and is the answer not in the manual?
Questions and answers