Related Manuals for Avigilon NVR5-10GBASET-A1
Summary of Contents for Avigilon NVR5-10GBASET-A1
- Page 1 Avigilon NVR5 10G Base-T Kit Installation Guide Installation Guide NVR5-10GBASET-A1 NVR5 STD 16TB-64TB NVR5 PRM 96TB-160TB...
- Page 2 © 2022, Avigilon Corporation. All rights reserved. AVIGILON, the AVIGILON logo, AVIGILON are trademarks of Avigilon Corporation. Intel is a trademark of Intel Corporation or its subsidiaries in the U.S. and/or other countries. Other names or logos mentioned herein may be the trademarks of their respective owners. The absence of the symbols ™...
-
Page 3: Table Of Contents
Table of Contents Introduction Confirm Package Contents Recommended Tools Installing the NVR5 10G Base-T Kit Opening the Cover Installing the 10G Base-T Card Reattaching the Cover Confirming the Installation For More Information... -
Page 4: Introduction
Introduction Avigilon provides an optional 10G Base-T Kit for the NVR5 Standard 16-64 TB and Premium 96-160 TB. This kit provides you with high-speed Ethernet ports for faster connections to your security network of ACC Servers and Clients. Part Number Description NVR5-10GBASET-A1... -
Page 5: Installing The Nvr5 10G Base-T Kit
Installing the NVR5 10G Base-T Kit Note: If the NVR5 is an operating part of your security system, be aware that it must be shut down to complete this procedure. Before starting to install the kit: 1. Turn off the NVR5, including all attached peripherals. Press the power button on the front panel, and wait for the light to stop blinking to indicate shutdown is complete. -
Page 6: Opening The Cover
Opening the Cover 1. At the top of the NVR5, unlock the latch release then lift and rotate the latch towards the back of the unit. The cover slides back and is released from the body. Tip: Use a Phillips #2 screwdriver to remove the shipping screws before unlatching the cover if you are removing the cover of an NVR5 for the first time. - Page 7 3. View the interior of the NVR5 and identify the locations where the components of the kit will be installed. The view below shows the details of an NVR5 with all of the covers and cards removed, and important components labeled with numbers. The components affected by the NVR5 10G Base-T Upgrade Kit are: 6—Expansion card riser The 10G Base-T card will be installed in one of the empty expansion slots to the left of this riser...
-
Page 8: Installing The 10G Base-T Card
Installing the 10G Base-T Card With the NVR5 open: 1. Unpack the 10G Base-T card. 2. Locate the slot in which the Base-T card will be installed and remove the PCI expansion slot cover from the back panel of the NVR5: For an NVR5 Premium system, the card will be installed in slot 5. -
Page 9: Reattaching The Cover
Reattaching the Cover When all the components of the kit have been installed: 1. Reinstall the top of the cooling shroud: a. Align the slot on the air shroud with the standoff in the system. b. Lower the air shroud into the system until it is firmly seated. 2. -
Page 10: Confirming The Installation
Under the Network Adapters heading, there should be four new ports installed in PCIe slot 5 or 6 (depending on Premium or Standard). These new ports should have a Link Speed of 10Gbps. Limited Warranty Avigilon warranty terms for this product are provided at avigilon.com/warranty. Confirming the Installation... -
Page 11: For More Information
For More Information For additional product documentation and software and firmware upgrades, visit support.avigilon.com. Technical Support Contact Avigilon Technical Support at support.avigilon.com/s/contactsupport. For More Information...
Need help?
Do you have a question about the NVR5-10GBASET-A1 and is the answer not in the manual?
Questions and answers