Related Manuals for Meinberg IMS-HPS-100
Summary of Contents for Meinberg IMS-HPS-100
- Page 1 MANUAL IMS-HPS-100 Setup Guide Hot-Plug Module November 3, 2023 Meinberg Funkuhren GmbH & Co. KG...
-
Page 3: Table Of Contents
Table of Contents 1 Imprint 2 Copyright and Liability Exclusion 3 Important Safety Information Appropriate Usage ..........Product Documentation . -
Page 4: Imprint
1 Imprint 1 Imprint Meinberg Funkuhren GmbH & Co. KG Lange Wand 9, 31812 Bad Pyrmont, Germany Phone: + 49 (0) 52 81 / 93 09 - 0 Fax: + 49 (0) 52 81 / 93 09 - 230 Website: https://www.meinbergglobal.com Email: info@meinberg.de... -
Page 5: Copyright And Liability Exclusion
Meinberg reserves the right to make changes of any type to this document at any time as is necessary for the purpose of improving its products and services and ensuring compliance with applicable standards, laws &... -
Page 6: Important Safety Information
Depending on your specific device configuration and installed options, some safety information may not be applicable to your device. Meinberg accepts no responsibility for injury or death arising from a failure to observe the safety information, warnings, and safety-critical instructions provided in the product documentation. -
Page 7: Product Documentation
Never open a power supply module—hazardous voltages may still reside within the module even after it is disconnected from the power source. If a power supply module is defective, it can be sent to Meinberg for repair. -
Page 8: Important Product Information
4.3 Maintenance and Modifications Important! Before performing any maintenance work on or authorized modification to your Meinberg system, we recommend making a backup of any stored configuration data (e.g., to a USB flash drive from the Web Interface). IMS-HPS-100 Setup Guide... -
Page 9: Prevention Of Esd Damage
ESD-proof bags that are crumpled or have holes cannot provide effective protection against electrostatic discharges. ESD-proof bags must have a sufficient electrical resistance and must not be made of conductive metals if the ESDS component has a lithium battery fitted on it. Date: November 3, 2023 IMS-HPS-100 Setup Guide... -
Page 10: Disposal
"IT and Telecommunications Equipment" in accordance with Annex I of the Directive. It can be returned to Meinberg for disposal. In this case, the shipping costs are to be borne by the cus- tomer, while Meinberg will cover the costs for disposal. If you wish for Meinberg to handle disposal for you, please get in touch with us. -
Page 11: Replacement Or Installation Of A Hot-Pluggable Ims Module
Make sure that the module is securely locked into the connector block before you fasten the two screws. Now you can put the installed module into operation. Attachment points of an 1U IMS system Date: November 3, 2023 IMS-HPS-100 Setup Guide... -
Page 12: Important Information Regarding Hot-Pluggable Ims Modules
Information: The NTP service and access to the web interface will be unavailable while the CPU is not installed. Management and monitoring functions will also be disabled. IMS-HPS-100 Setup Guide Date: November 3, 2023... -
Page 13: Hps-100: Ptp / Synce / Hardware Ntp Interface
1-Step, 2-Step for both Master and Slave operation Synchronous Ethernet: Master and Slave Capability Compliant to ITU-T G.8261, G.8262 and G.8264 Ethernet Synchronization Messaging Channel (ESMC) Network Protocols: IPv4, IPv6 DHCP, DHCPv6 DSCP IEEE 802.1q VLAN filtering/tagging IEEE 802.1p QOS Date: November 3, 2023 IMS-HPS-100 Setup Guide... - Page 14 - red stopped Performance Level Options: Option Unicast Delay PTPv1 Clients Req./s Req./s Monitoring ————————————————————————————————————————————- PL-A 1024 1600 PL-B 32768 51200 PL-C 65536 102400 PL-D 1024 131072 204800 PL-E 2048 262144 409600 IMS-HPS-100 Setup Guide Date: November 3, 2023...
-
Page 15: Hps100 - Global Configuration
PTP standard allows it. Depending on the selected profile, there might be profile specific parameters available which can be found in the “Profile Specific Parameters“ section below the standard PTP parameters sections. Date: November 3, 2023 IMS-HPS-100 Setup Guide... -
Page 16: Option: Output Configuration
• 2.048 MHz (taken from active internal clock module) • 10 MHz (taken from active internal clock module) • PPS (taken from active internal clock module) Per default no output signal is active on both outputs. IMS-HPS-100 Setup Guide Date: November 3, 2023... -
Page 17: Firmware Update Via Web Interface
The update file can be uploaded to the HPS100 by first choosing the file on your local computer with the "Browse" button and then press "Start Update". Afterwards you are prompted to confirm the start of the update process. Date: November 3, 2023 IMS-HPS-100 Setup Guide... -
Page 18: Sfp Transceiver
IEC standard 60825-1 may emit radiation capable of causing eye injuries. • Never look into an unconnected connector of a fiber optic cable or an unconnected SFP port, and ensure that unused fiber optic connectors are always fitted with a suitable protective cap. IMS-HPS-100 Setup Guide Date: November 3, 2023... -
Page 19: Rohs Conformity
EU do not contain lead, cadmium, mer- cury, hexavalent chromium, polybrominated biphenyls (PBBs), polybrominated diphenyl ethers (PBDEs), bis(2-ethylhexyl)phthalat (DEHP), benzyl butyl ph- thalate (BBP), dibutyl phthalate (DBP), or diisobutyl phthalate (DIBP) above the legal limits. Date: November 3, 2023 IMS-HPS-100 Setup Guide...
Need help?
Do you have a question about the IMS-HPS-100 and is the answer not in the manual?
Questions and answers