Subscribe to Our Youtube Channel
Related Manuals for Meinberg IMS-HPS-100
Summary of Contents for Meinberg IMS-HPS-100
- Page 1 MANUAL IMS-HPS-100 Setup Guide Hot-Plug Module April 24, 2023 Meinberg Funkuhren GmbH & Co. KG...
-
Page 3: Table Of Contents
Table of Contents 1 Imprint 2 Copyright and Liability Exclusion 3 Important Safety Information Product Documentation ......... . . Prevention of ESD Damage . -
Page 4: Imprint
1 Imprint 1 Imprint Meinberg Funkuhren GmbH & Co. KG Lange Wand 9, 31812 Bad Pyrmont, Germany Phone: + 49 (0) 52 81 / 93 09 - 0 Fax: + 49 (0) 52 81 / 93 09 - 230 Website: https://www.meinbergglobal.com Email: info@meinberg.de... -
Page 5: Copyright And Liability Exclusion
Meinberg reserves the right to make changes of any type to this document at any time as is necessary for the purpose of improving its products and services and ensuring compliance with applicable standards, laws &... -
Page 6: Important Safety Information
• Take note of the chapter "Power Supply". 3.1 Product Documentation Detailed product documentation is provided on a USB flash drive delivered with the Meinberg system. The manuals can also be downloaded from the Meinberg website at https://www.meinbergglobal.com, where you can enter your system name into the search box at the top of the page to find the relevant manual. -
Page 7: Prevention Of Esd Damage
ESD-proof bags that are crumpled or have holes cannot provide effective protection against electrostatic discharges. ESD-proof bags must have a sufficient electrical resistance and must not be made of conductive metals if the device has a lithium battery fitted on it. Date: April 24, 2023 IMS-HPS-100 Setup Guide... -
Page 8: Power Supply
In the event that a power supply unit is no longer working (e.g. defective), please return it to Meinberg for repair. Failure to observe these safety instructions may result in serious injury and/or property damage. -
Page 9: Replacement Or Installation Of A Hot-Pluggable Ims Module
Make sure that the module is securely locked into the connector block before you fasten the two screws. Now you can put the installed module into operation. Attachment points of an 1U IMS system Date: April 24, 2023 IMS-HPS-100 Setup Guide... -
Page 10: Important Information Regarding Hot-Pluggable Ims Modules
Operating System, the configuration of some IMS modules may be reset to factory defaults! Information: The NTP service and access to the web interface will be unavailable while the CPU is not installed. Management and monitoring functions will also be disabled. IMS-HPS-100 Setup Guide Date: April 24, 2023... -
Page 11: Hps-100: Ptp / Synce / Hardware Ntp Interface
1-Step, 2-Step for both Master and Slave operation Synchronous Ethernet: Master and Slave Capability Compliant to ITU-T G.8261, G.8262 and G.8264 Ethernet Synchronization Messaging Channel (ESMC) Network Protocols: IPv4, IPv6 DHCP, DHCPv6 DSCP IEEE 802.1q VLAN filtering/tagging IEEE 802.1p QOS Date: April 24, 2023 IMS-HPS-100 Setup Guide... - Page 12 102400 PL-D 1024 131072 204800 PL-E 2048 262144 409600 A detailed configuration guide you will find in the corresponding firmware manual of the system. See chapter "The Web Interface -> Configuration: PTP V2". IMS-HPS-100 Setup Guide Date: April 24, 2023...
-
Page 13: Hps100 - Global Configuration
PTP standard allows it. Depending on the selected profile, there might be profile specific parameters available which can be found in the “Profile Specific Parameters“ section below the standard PTP parameters sections. Date: April 24, 2023 IMS-HPS-100 Setup Guide... -
Page 14: Option: Output Configuration
• 2.048 MHz (taken from active internal clock module) • 10 MHz (taken from active internal clock module) • PPS (taken from active internal clock module) Per default no output signal is active on both outputs. IMS-HPS-100 Setup Guide Date: April 24, 2023... -
Page 15: Firmware Update Via Web Interface
The update file can be uploaded to the HPS100 by first choosing the file on your local computer with the "Browse" button and then press "Start Update". Afterwards you are prompted to confirm the start of the update process. Date: April 24, 2023 IMS-HPS-100 Setup Guide... -
Page 16: Rohs And Weee
WEEE-compliant fashion, it may be returned to the manufacturer. Any transportation ex- penses for returning this product (at end-of-life) must be covered by the end user, while Meinberg will bear the costs for the waste disposal itself. IMS-HPS-100 Setup Guide...
Need help?
Do you have a question about the IMS-HPS-100 and is the answer not in the manual?
Questions and answers