Subscribe to Our Youtube Channel
Related Manuals for Meinberg IMS-VSG181
Summary of Contents for Meinberg IMS-VSG181
- Page 1 SETUP GUIDE IMS-VSG181 Hot-Plug Module 25th January 2021 Meinberg Funkuhren GmbH & Co. KG...
-
Page 3: Table Of Contents
IMS-VSG181 - Status LEDs ........ -
Page 4: Imprint
1 Imprint 1 Imprint Meinberg Funkuhren GmbH & Co. KG Lange Wand 9, 31812 Bad Pyrmont / Germany Phone: + 49 (0) 52 81 / 93 09 - 0 Fax: + 49 (0) 52 81 / 93 09 - 230 Internet: https://www.meinbergglobal.com... -
Page 5: Introduction
Meinberg product. Download LTOS7 Firmware manual: https://www.meinbergglobal.com/download/docs/manuals/english/ltos_7-00.pdf Compatibility The IMS-VSG181 is an IMS module which is compatible with all systems of the IMS family. It can also be used on any slot (MRI, ESI, I/O). Date: 25th January 2021 IMS-VSG181... -
Page 6: Important Safety Hints
Before any maintenance work on the system: • Backup of stored configurations is recommended (e.g. via USB stick or Web UI) • Please note the chapter "Prevention of ESD damage". • Please note the chapter "Supply voltage". IMS-VSG181 Date: 25th January 2021... -
Page 7: Additional Safety Hints
Keep all documents provided with the device for later reference. This manual is exclusively for qualified electricians or by a qualified electrician trained personnel who are familiar with the applicable national standards and specifications, in particular for the construction of high voltage devices. Date: 25th January 2021 IMS-VSG181... -
Page 8: Prevention Of Esd Damage
ESD protective covers, which are extremely wrinkled or even have holes, no longer protect against electrostatic discharge. ESD protective covers must not be low-resistance and metallically conductive if a lithium battery is installed on the assembly. IMS-VSG181 Date: 25th January 2021... -
Page 9: Supply Voltage
Never open a power supply unit cause dangerous voltages can even exist after it has been disconnected from the electrical supply. If a power supply is not working anymore, e.g. due to a defect, please send it back to Meinberg for necessary repairs. Non-observance of these safety instructions can cause serious personal injury and material damage. Installation, initial start-up and operation of the IMS System may only be performed by qualified technical experts. -
Page 10: Front Connectors Ims-Vsg181
4 Front Connectors IMS-VSG181 4 Front Connectors IMS-VSG181 IMS-VSG181 Date: 25th January 2021... -
Page 11: Ims-Vsg181 - Status Leds
4.1 IMS-VSG181 - Status LEDs Status display LED St: Status of the VSG181 LED In: Synchronization status LED A: Status of the Blackburst output LED B: Status of the LTC output St In A B The status messages of the LED’s are as follows:... -
Page 12: Black Burst Output
4 Front Connectors IMS-VSG181 4.2 Black Burst Output Output Signal: PAL, NTSC Black Burst with VITC Support or Tri-Level-Sync Signal level: 300 mV into 75 ohms (unbalanced) Formats: Black Burst: PAL (SMPTE259M/ITU-R BT.470-6) NTSC (SMPTE170M/ITU-R BT.470-7) VITC (SMPTE12M-1/SMPTE ST309M) Tri-Level-Sync:... -
Page 13: Word Clock Output
Frequency range: 24 Hz - 12,288 MHz Base frequencies: 44.1 kHz and 48 kHz Scaling factor: 0.125, 0.25, 0.5, 1, 2, 4, 8, 16, 32, 64, 128, 256 Connection type: BNC female connector. Cable: coaxial, shielded Date: 25th January 2021 IMS-VSG181... -
Page 14: Before You Start
5.1 Scope of Delivery Unpack the IMS-VSG181 carefully and check the scope of delivery against the enclosed packing list to en- sure that no parts are missing. If any of the listed items are missing, please contact our sales department: sales@meinberg.de... -
Page 15: System Installation
CPU is disconnected. Also the management and monitoring functions are no longer available. RSC/SPT: "hot plugable" The switching function or the distribution of generated signals is interrupted while the RSC/SPT is disconnected. Date: 25th January 2021 IMS-VSG181... -
Page 16: Installation Of Hot-Pluggable Ims Modules
Make sure that the module is securely locked into the connector block before you fasten the two screws. Now you can put the installed module into operation. Attachment points of an 1U IMS system IMS-VSG181 Date: 25th January 2021... -
Page 17: Configuration Of The Ims-Vsg181
7 Configuration of the IMS-VSG181 This chapter explains how to put a IMS-VSG181 into operation via the web interface. 7.1 Configuration To configure the IMS-VSG181, select the I/O Config –> Configuration of Outputs menu in the web interface. Black Burst ———————————————————————-... - Page 18 7 Configuration of the IMS-VSG181 Timecode: The following timecodes can be selected: VITC VITC w. daily jam (only NTSC) VITC w. daily jam and drop frame (only NTSC) Time zone: Select the desired time zone. 1st time code line: Select the 1st line, in which the...
- Page 19 Select a multiplier by which the base frequency is to be multiplied. The result is the frequency of the output signal. Label: You have the possibility to enter an individual label for the output or leave the field empty. ———————————————————————- Date: 25th January 2021 IMS-VSG181...
-
Page 20: Rohs And Weee
Any transportation expenses for return- ing this product (at its end of life) have to be incurred by the end user, whereas Meinberg will bear the costs for the waste disposal itself. IMS-VSG181...
Need help?
Do you have a question about the IMS-VSG181 and is the answer not in the manual?
Questions and answers