Subscribe to Our Youtube Channel
Related Manuals for Meinberg IMS-LNE-GBE-SFP
Summary of Contents for Meinberg IMS-LNE-GBE-SFP
- Page 1 MANUAL IMS-LNE-GBE-SFP Setup Guide Hot-Plug Module May 31, 2023 Meinberg Funkuhren GmbH & Co. KG...
-
Page 3: Table Of Contents
Table of Contents 1 Imprint 2 Important Safety Information Product Documentation ......... . . Prevention of ESD Damage . - Page 4 1 Imprint 1 Imprint Meinberg Funkuhren GmbH & Co. KG Lange Wand 9, 31812 Bad Pyrmont, Germany Phone: + 49 (0) 52 81 / 93 09 - 0 Fax: + 49 (0) 52 81 / 93 09 - 230 Website: https://www.meinbergglobal.com Email: info@meinberg.de...
-
Page 5: Important Safety Information
• Take note of the chapter "Power Supply". 2.1 Product Documentation Detailed product documentation is provided on a USB flash drive delivered with the Meinberg system. The manuals can also be downloaded from the Meinberg website at https://www.meinbergglobal.com, where you can enter your system name into the search box at the top of the page to find the relevant manual. -
Page 6: Prevention Of Esd Damage
ESD-proof bags that are crumpled or have holes cannot provide effective protection against electrostatic discharges. ESD-proof bags must have a sufficient electrical resistance and must not be made of conductive metals if the device has a lithium battery fitted on it. IMS-LNE-GBE-SFP Setup Guide Date: May 31, 2023... -
Page 7: Power Supply
In the event that a power supply unit is no longer working (e.g. defective), please return it to Meinberg for repair. Failure to observe these safety instructions may result in serious injury and/or property damage. -
Page 8: Replacement Or Installation Of A Hot-Pluggable Ims Module
Make sure that the module is securely locked into the connector block before you fasten the two screws. Now you can put the installed module into operation. Attachment points of an 1U IMS system IMS-LNE-GBE-SFP Setup Guide Date: May 31, 2023... -
Page 9: Important Information Regarding Hot-Pluggable Ims Modules
Information: The NTP service and access to the web interface will be unavailable while the CPU is not installed. Management and monitoring functions will also be disabled. Date: May 31, 2023 IMS-LNE-GBE-SFP Setup Guide... -
Page 10: Lne-Gbe-Sfp: Network Expansion With Gigabit Support For Ims Systems
Humidity: Max. 85% LED Indicators LED St: Init lights blue during initialisation LED In - LED B: Shows the state of the four LAN ports after initialisation green normal operation defective LAN port IMS-LNE-GBE-SFP Setup Guide Date: May 31, 2023... - Page 11 In a factory assembling, LNE modules are sorted in an ascending order starting from left to right (see the corresponding figure above). LAN 0 is therefore always the first network interface of the LAN-CPU. Date: May 31, 2023 IMS-LNE-GBE-SFP Setup Guide...
-
Page 12: Lne-Gbe Configuration Via The Web Interface
IPv6 Mode: This mode must be activated here. MAC-Address: Displays the unique MAC address of the physical interface. Assigned Virtual Interfaces: In the Ethernet Interfaces menu (see below) virtual network interfaces can be added. IMS-LNE-GBE-SFP Setup Guide Date: May 31, 2023... - Page 13 With VLAN, this function can be enabled and configured. Cluster: The cluster function can be activated with this submenu and additional Parameters such as multicast or unicast mode, TCP / IP address and subnet mask can be set up here. Date: May 31, 2023 IMS-LNE-GBE-SFP Setup Guide...
-
Page 14: Adding / Removing An Lantime Network Extension Lne
LNE interfaces are still listed in the network configuration. The "NIC Manager" can be used to update the network configuration in this case as well. After successfully running the "NIC Manager", only the actually existing interfaces are displayed in the web interface. A system restart is not necessary. IMS-LNE-GBE-SFP Setup Guide Date: May 31, 2023...
Need help?
Do you have a question about the IMS-LNE-GBE-SFP and is the answer not in the manual?
Questions and answers