Hay NEW ORDER Manual
SHELVING SYSTEM
![Hay - NEW ORDER - SHELVING SYSTEM SHELVING SYSTEM]()
PARTS
![Hay - NEW ORDER - SHELVING SYSTEM - PARTS - Part 1 SHELVING SYSTEM - PARTS - Part 1]()
![Hay - NEW ORDER - SHELVING SYSTEM - PARTS - Part 2 SHELVING SYSTEM - PARTS - Part 2]()
![Hay - NEW ORDER - SHELVING SYSTEM - PARTS - Part 3 SHELVING SYSTEM - PARTS - Part 3]()
SHELVING SYSTEM - ASSEMBLY
- Before starting assembly, use a spirit level to ensure the bottom shelves
are level. Adjust the feet if the bottom shelves need levelling by unscrewing the adjustable feet, either by hand or with the Allen key
from the top.
![Hay - NEW ORDER - SHELVING SYSTEM - ASSEMBLY - Step 1 SHELVING SYSTEM - ASSEMBLY - Step 1]()
- Mount the profiles
,
and
onto the bottom shelves ![]()
.![Hay - NEW ORDER - SHELVING SYSTEM - ASSEMBLY - Step 2 SHELVING SYSTEM - ASSEMBLY - Step 2]()
- Add the middle shelves
and the top shelves
. Then tighten all fixed screws in both ends of the profiles with the Allen key
. to secure the construction.
Then add the next layer of profiles.
- Add the top tray
and the top shelves
. Then tighten all fixed screws in both the top and bottom of the profiles.
- Make sure all fixed screws are tightened.
WALL SAFETY BRACKET
![Hay - NEW ORDER - WALL SAFETY BRACKET WALL SAFETY BRACKET]()
PARTS
![Hay - NEW ORDER - WALL SAFETY BRACKET - PARTS WALL SAFETY BRACKET - PARTS]()
WALL SAFETY BRACKET - ASSEMBLY
- Always mount wall panels and wall brackets under the top shelf.
Place the bracket holder
in the channel running along the shelf and flip it down by following the steps 1, 2 and 3 below.
- Screw the bracket
into place using the screws
and torx key
Do not tighten the screws completely. Mark the holes, and slide the bracket to the side and drill holes in the wall. Fasten the bracket with the screws.
![Hay - NEW ORDER - WALL SAFETY BRACKET - ASSEMBLY - Step 2 WALL SAFETY BRACKET - ASSEMBLY - Step 2]()
- Tighten the screws
completely.
FLOOR SAFETY BRACKET
PARTS
![Hay - NEW ORDER - FLOOR SAFETY BRACKET - PARTS FLOOR SAFETY BRACKET - PARTS]()
FLOOR SAFETY BRACKET - ASSEMBLY
- Make sure the shelf is level. Adjust the feet with the Allen key if needed.
Slide the brackets in from the sides and mark their position.
- Drill holes where marked. Position the brackets and screw them into place.
Make sure the openings at the ends are facing the same direction.
- Slide the shelf into position.
WALL BRACKET SHELF / TRAY
PARTS
![Hay - NEW ORDER - WALL BRACKET SHELF / TRAY - PARTS WALL BRACKET SHELF / TRAY - PARTS]()
WALL BRACKET SHELF / TRAY - ASSEMBLY
- Start by marking where the mounting holes for the brackets should be placed using the template below. Also use a spirit level to ensure the brackets are level. Use the appropriate screws and plugs according to the following screw guide for wall mounting.
- Remove the feet from the bottom shelf or tray. Mount the shelving system onto the brackets by pushing the shelving system up against the wall and letting it slide down, hooking onto the wall brackets both on the top and bottom.
- To build the wall brackets vertically, mount the brackets in each section and column.
PLEASE NOTE:
Use one set of wall brackets per shelf / tray layer.
GUIDELINE WALL MOUNTING
WOODEN WALLS
Use suitable wood screws.
![]()
CONCRETE OR BRICK WALLS
Use suitable screws and expansion plugs.
![]()
DRYWALL OR CHIPBOARD
Use suitable expanding bolts.
![]()
PLEASE NOTE
These are only intended as guidelines. The buyer is responsible for the wall's bearing capacity and for ensuring the correct mounting method is used.
ACCESSORIES
WHEELS
![Hay - NEW ORDER - ACCESSORIES - WHEELS - Step 1 ACCESSORIES - WHEELS - Step 1]()
- Start unscrewing the feet of the bottom shelf or tray.
Then mount the wheels with the braking wheels diagonally using the supplied wrench.
![Hay - NEW ORDER - ACCESSORIES - WHEELS - Step 2 ACCESSORIES - WHEELS - Step 2]()
PLEASE NOTE
Retighten all wheels three to four weeks after assembly.
![]()
- Only mount wheels on shelves with two layers.
BENCHTOP
![Hay - NEW ORDER - ACCESSORIES - BENCHTOP - Step 1 ACCESSORIES - BENCHTOP - Step 1]()
- Peel off the paper, protecting the adhesive tape of the velcro and apply the cushion to the shelf. Make sure that it is aligned with all four corners.
![Hay - NEW ORDER - ACCESSORIES - BENCHTOP - Step 2 ACCESSORIES - BENCHTOP - Step 2]()
PLEASE NOTE
Only use the benchtop on the second layer.
![Hay - NEW ORDER - ACCESSORIES - BENCHTOP - Step 4 ACCESSORIES - BENCHTOP - Step 4]()
BOOK DIVIDER
![Hay - NEW ORDER - ACCESSORIES - BOOK DIVIDER - Step 1 ACCESSORIES - BOOK DIVIDER - Step 1]()
- Mount the book divider by tilting it 45 degrees and placing it in the channel running along the shelf. Then tilt the book divider downwards.
CARE & MAINTENANCE
Our Care & Maintenance offers guidance for optimal maintenance of your HAY product. It includes advice and instructions on cleaning and caring for specific materials to prolong the life of your furniture.
Please find our Care & Maintenance guide by scanning the QR code
![]()
You can find more relevant information on New Order Shelving System by scanning the QR code
![]()
You can also find the same information here hay.dk/downloads
SAFETY INSTRUCTIONS
NEW ORDER SAFETY INSTRUCTIONS
![Hay - NEW ORDER - SAFETY - NEW ORDER SAFETY INSTRUCTIONS SAFETY - NEW ORDER SAFETY INSTRUCTIONS]()
MAX BUILDING HEIGHT
![Hay - NEW ORDER - SAFETY - MAX BUILDING HEIGHT SAFETY - MAX BUILDING HEIGHT]()
ALWAYS USE SAFETY BRACKETS IN THE FOLLOWING CASES
![]()
Documents / Resources
References
Download manual
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download Hay NEW ORDER Manual
Need help?
Do you have a question about the NEW ORDER and is the answer not in the manual?
Questions and answers