Advertisement
Quick Links
Advertisement
Related Manuals for Hay STEFAN DIEZ NEW ORDER
Summary of Contents for Hay STEFAN DIEZ NEW ORDER
- Page 1 – INSTRUCTION MANUAL – NEW ORDER MEDIA UNIT DESIGN BY STEFAN DIEZ...
- Page 3 – INTRODUCTION – Developed in collaboration with HAY, Stefan Diez’s New Order Media Unit is part of a modular shelving and table system designed to fit the ever-changing boundaries of contemporary workspace and living environments. The simple open-grid construction serves as a flexible and functional framework, enabling the user to create customized open or closed storage solutions.
- Page 5 – TABLE OF CONTENTS – CARE AND MAINTENANCE INSTRUCTIONS SHELVING SYSTEM 7-13 INSTRUCTIONS WALL SAFETY BRACKET 14-18 INSTRUCTIONS STEEL PANELS 19-24 INSTRUCTIONS STEEL DOORS 25-31...
- Page 6 – CARE AND MAINTENANCE – CAUTION POWDER COATED ALUMINUM With a little care you can prolong the life / Wipe with a clean cloth wrung in water of your furniture. Follow the instructions for or in a solution of water and a neutral the materials of your specific product to detergent.
- Page 7 – INSTRUCTION MANUAL – SHELVING SYSTEM...
- Page 8 – PARTS – Single profile Double profile Top shelves 100 cm / 39.5 in Allen key Middle shelves 100 cm / 39.5 in Bottom shelves 100 cm / 39.5 in...
- Page 9 Before starting assembly, use a spirit level to ensure the bottom shelves are level. Adjust the feet if the bottom shelves need levelling by unscrewing the adjustable feet, either by hand or with the Allen key from the top.
- Page 10 Mount the profiles onto the bottom shelves ALIGNMENT Make sure that the fixed screws are aligned with the channel running along the shelf. DOUBLE PROFILES Mount the Double Profiles in the middle to connect the two Bottom Shelves. AVOID GAPS Make sure that the profiles are pressed firmly against...
- Page 11 Add the middle shelves . Then tighten all fixed screws in both ends of the profiles with the Allen key G. to secure the construction. Then add the next layer of profiles. TIGHTEN ALL FIXED SCREWS Secure the construction by tightening all fixed screws in the first layer of profiles.
- Page 12 Add the top shelves . Then tighten all fixed screws in both the top and bottom of the profiles. TIGHTEN ALL FIXED SCREWS Secure the construction by tightening all fixed screws in the second layer of profiles.
- Page 13 Make sure all fixed screws are tightened.
- Page 14 - ACCESSORIES - WALL SAFETY BRACKET...
- Page 15 – PARTS – Bracket holder Bracket Screw Torx key...
- Page 16 Locate the shelves that will require cable routing and the safety brackets. Place the bracket holder in the channel running along the shelf approximately 3 inches from the profile. Flip it down by following the steps 1, 2 and 3 below. APPROX.
- Page 17 Screw the bracket into place using the screws and Torx key . Do not tight- en the screws completely. While the brackets are held in place, use a pencil to mark the center of the holes on the wall. Slide the bracket to the side and drill holes in the wall.
- Page 18 Undo the screws and install the back panels first (page 23 to 28), before tightening the screws completely.
- Page 19 – INSTRUCTIONS – STEEL PANELS...
- Page 20 – PARTS – Back panel Side panel Back panel Back panel with cable routing cutout...
- Page 21 Locate the shelves (2x) that will require the cable routing cutout. Mount the back panel by inserting the bent edge into the channel running along the bottom of the top shelf. Hold the shelf at an angle when inserting it and then slowly push the bottom edge of the panel into place.
- Page 22 Working inside the shelf, use the Allen key to push the small pins in the edges of the panel into the channel of both the bottom shelf and the corner profiles.
- Page 23 Insert the side panels from the long side of the shelf, and gently push them into place.
- Page 24 Lock the panels in place by pushing the small pins into the channel of the corner profiles.
- Page 25 – INSTRUCTIONS – STEEL DOORS...
- Page 26 – PARTS – Connector clip Steel door...
- Page 27 Insert the connector clips in the channels along the top and bottom of the lower shelves.
- Page 28 Rotate the end fitting on the steel door as shown in the illustration below.
- Page 29 Insert the fitting on the end of the steel door into the channel on the profile. Start with the door at an angle before rotating it into place.
- Page 30 To lock the door in place, use the Allen key to bend the small tab into the channels, both at the top and bottom.
- Page 31 Push the other end of the door into place by clicking the metal fitting into the connector clips and supporting it with your hand.
- Page 34 711 Canal Street 3 Floor Stamford CT 06902 www.hay.com 5/01/2021...
Need help?
Do you have a question about the STEFAN DIEZ NEW ORDER and is the answer not in the manual?
Questions and answers