Related Manuals for SPRT SP-POS8VI
Summary of Contents for SPRT SP-POS8VI
- Page 1 SPRT® POS Thermal printer user manual （SP-POS88Ⅵ） （Ver 1.01） Beijing Spirit Technology Development Co., Ltd...
- Page 2 Contents Brief Introduction ................. 错误!未定义书签。 Chapter 1 Characteristics and performance ........... 错误!未定义书签。 1.1 Print performance ..................... 3 1.2 Print paper ........................ 4 1.3 Print character ......................4 1.4 Interface type ......................4 1.5 Print control command ..................... 5 1.6 Power Requirement ....................5 1.7 Work environment ....................
- Page 3 Brief Introduction printer is a new type line thermal printer, it features in fast speed POS88Ⅵ print, low print noise, high reliability, perfect print quality and ribbon needless, avoiding the vexation of regular maintenance. printer: small in outline dimension, simple operation, and POS88Ⅵ...
- Page 4 （2）Cutter life: 500,000 cuts. Using condition: less than 30 cuts/minute ● Valid print width: 72mm Print Paper Thermal paper roll model ：TF50KS－E（Japan paper co.ltd） ● AF50KS-E(JUJO THERMAL) Thermal paper roll: Width－－－ 79.5±0.5mm ● Outer Diameter －－－ 80mm（max.） Inner Diameter－－－ 13mm（min.） Thickness －－－...
- Page 5 36-pin，8-bit parallel interface，BUSY/ACK handshaking protocol, TTL signal level. Ethernet Interface ： ● Normal Ethernet interface. USB Interface： ： ● USB interface Cash Drawer Control ： ● DC24V，1A，6-pin RJ-11 socket. Print Control Commands Character print commands: support double-width, double height print of ●...
- Page 6 Operation Environment Operation temperature: 5～50℃; Relative humidity: 10～80％ ● ● Storage temperature: -40～55℃; Relative humidity: 10～90℃ Outline Dimension ●212（L）mm×150（W）mm×135（H）mm Model classification Model Interface SP-POS88ⅥSF RS－232C Serial Interface SP-POS88ⅥS SP-POS88ⅥPF Parallel Interface SP-POS88ⅥP SP-POS88ⅥEF Ethernet Interface SP-POS88ⅥE SP-POS88ⅥUF USB Interface SP-POS88ⅥU...
- Page 7 Chapter 2 Operation instruction Printer Appearance Paper Cover Power Indicator（green Status Indicator (red) Paper-end Indicator (red) Paper Feed Decap button Paper-out slot Cutter cover...
- Page 8 Power Switch Cash driver interface Interface socket Power socket Paper Installation 2.2.1 Paper Loading adopts 79.5mm width thermal paper roll. POS88Ⅵ Steps of Loading Thermal Paper Are as below: Hold down the upper cover button on the left side, open the movable upper cover, draw a certain length of the paper roll, put the paper end on the print head, close the upper cover and press it downwards lightly.
- Page 9 3.Keep clean of the print head,avoid to influence the printing quality. 2.2.2 Solution to Paper Jam If cutter jam,turn off the power,and turn on again,the cutter will be back to original position.If paper jam,open the paper strage cover,and take out the paper.If the cutter can not be back to the original position,open the cover of it,and turn the white plastic gear by the direction suggestive on the cutter by hand to make the cutter be back to the original position.
- Page 10 Fig.2-2 Pin Order of Serial Port The pin assignment of serial interface is shown in Fig. 2-3: Signal Signal Sourc Description Name Direction —— —— Cover ground Output Printer Printer transmits control code X-ON/X-OFF and data to host Input Host Printer receives data from host Output Printer...
- Page 11 —— —— Signal Ground Output Printer Signal “MARK” means the host is busy and can not receive data.Signal “SPACE” means the host is ready to receive data. Fig. 2-3 The pin assignment of serial interface Note: (1)“Source” denotes the source that signal come from; (2)Logical signal level is EIA.
- Page 12 2.3.2 Parallel Interface The parallel interface of POS88VI printer is compatible with CENTRONICS, supports BUSY or ACK handshaking protocol, uses 36pin CENIRONICS socket (female) The pin assignment of DB25 parallel interface is as Fig. 2-5 shows: Pin No. Signal Direction Description STROBE Strobe pulse to latch data, Reading...
- Page 13 Answer pulse, LOW level signal indicates that data have already been received and the printer gets ready to receive the next data. BUSY HIGH level signal indicates that the printer is BUSY and can not receive data. HIGH level signal indicates that paper is end.
- Page 14 Logic-H Logic “1” level nFault Low level means the printer is at fault 14,15,17 18,34,36 No connection 16,19~30, Grounding logical 0 level +5V power Fig.2-6 Signal Timing Chart of Parallel Interface ：...
- Page 15 2.3.3 Cash Drawer Interface The cash drawer interface of POS-POS88VI adopts RJ-11 6-pin socket, as Fig.2-7 shows: Fig.2-7 Cash Drawer Interface The pin assignment is as below ： Pin No. Signal Direction Chassis Ground —— Cash drawer driver signal 1 Cash drawer on/off status signal +24VDC ——...
- Page 16 Pin No. Signal +24VDC Ground The pin assignment is as above： Light, buzzer and keystrokes There is one button and three indicators on POS88VI printer. 【FEED】 is paper feeding button, the function of its enabling or disabling the button on/off can be set by print command, when the button is enabled, press 【FEED】...
- Page 17 alarm status, said when the indicator is long on the printing paper in the process of the open cover. Error indicator lights flashing, buzzer rang: printer error. According to blink in a different way, indicates the printer error types: Unrecoverable error, lights flicker frequency and number of buzzer rang said 1、...
- Page 18 ② Can automatically recover the error, continuous flashing lights. Including the print head temperature error and the upper cover to open the print process error. instructions ERROR light type of error strobe automatic error Continuous flashing LED: the print recovery head is overheating, upper cover to open the print process error.
- Page 19 2.7 Hexadecimal Printing Turn on the printer according to the step below,it will enter the mode of Hexadecimal Printing 1.Open the cover； 2.Hold down【FEED】button，and connect with power； 3.Close the cover,the printer will print out 3 lines as below: Hexadecimal Dump To terminate hexadecimal dump, Press FEED button three times.
- Page 20 the cover 】 【 paper storehouse. The printer into parameter setting mode. And print out the first item can be set parameters and its current value.Please see the appendix A part of the set method in detail. Exit parameters setting method: open cover 】 【 paper first, and then hold down the "FEED"...
- Page 21 FEED Font dots： FEED 12×24 9×17 FEED ： Print Density FEED FEED 中 高 低 FEED Print speed： FEED FEED FEED 250mm/s 200mm/s 220mm/s 150mm/s Eenglish China China FEED ： Buzzer FEED FEED FEED ALL ON Error ON Cut ON FEED Re-printing lack of paper：...
Need help?
Do you have a question about the SP-POS8VI and is the answer not in the manual?
Questions and answers