Related Manuals for Moxa Technologies ToughNet TN-5900 Series
Summary of Contents for Moxa Technologies ToughNet TN-5900 Series
- Page 1 TN-5916 Series Quick Installation Guide Moxa ToughNet NAT Router Version 3.1, January 2021 Technical Support Contact Information www.moxa.com/support 2021 Moxa Inc. All rights reserved. P/N: 1802059160012 *1802059160012*...
-
Page 2: Package Checklist
Overview The ToughNet TN-5916 is a high performance M12 Layer 3 NAT Router that supports Layer 3 routing functionality to facilitate the deployment of applications across networks. The TN-5916 NAT router uses M12 and other circular connectors to ensure tight, robust connections and guarantee reliable operation against environmental disturbances, such as vibration and shock. -
Page 3: Recommended Optional Accessories
Recommended Optional Accessories • CBL-M23(FF6P)Open-BK-100-IP67: 1-meter M23 to 6-pin power cable with IP67-rated female 6-pin M23 connector • CBL-M12D(MM4P)/RJ45-100 IP67: 1-meter M12-to-RJ45 Cat-5E UTP Ethernet cable with IP67-rated male 4-pin M12 D-coded connector • CBL-M12(FF5P)/OPEN-100 IP67: 1-meter M12-to-5-pin power cable with IP67-rated female 5-pin M12 A-coded connector •... -
Page 4: Tn-5916 Panel Layouts
TN-5916 Panel Layouts 1. Model name 2. Screw holes for panel mounting kit 3. Console port 4. Grounding screw 5. Relay output port 6. Power input voltage range indicator 7. Power input port (male 6-pin shielded M23 connector) 8. PWR1 LED: for power input 1 9. -
Page 5: Mounting Dimensions (Unit = Mm)
NOTE On the TN-5916-ETBN, ETB ports representing DIR1 are marked as A1 and B1, and ports representing DIR2 are marked as A2 and ATTENTION DO NOT open or remove the vent (#15). Removing the seal will invalidate the warranty. Ports (including 3, 5, and 14) that are not in use must be tightly covered with protective caps (an optional accessory) to ensure IP54/IP67-rated protection. -
Page 6: Panel/Wall Mounting
Panel/Wall Mounting STEP 1: Mounting the TN-5916 to a wall requires 4 screws. Use the ToughNet router as a guide to mark the correct positions of the 4 screws. STEP 2: Use the 4 screws in the panel mounting kit. If you would like to use your own screws, make sure the screw head is between 6.0 mm and 7.0 mm in diameter and... -
Page 7: Wiring Requirements
STEP 2: If the spring-loaded bracket is locked in place, push the recessed button to release it. Once released, you should feel some resistance from the spring as you slide the bracket up and down a few millimeters in each direction. -
Page 8: Grounding The Toughnet Nat Router
ATTENTION Safety First! Be sure to disconnect the power cord before installing and/or wiring your Moxa router. This device has UL 508 approval. Use copper conductors only, 60 to 75°C, and tighten to 4.5 inch-pounds. For use in pollution degree 2 environments. ATTENTION Safety First! Observe all electrical codes dictating the maximum current... -
Page 9: Connecting The Power Supplies
ATTENTION This product is intended to be mounted to a well-grounded mounting surface such as a metal panel. Connecting the Power Supplies The ToughNet TN-5916 series routers support two sets of power supplies—power input 1 and power input 2. The M23 6-pin male connector on the TN-5916’s front panel is used for the dual power inputs. -
Page 10: Connecting The Relay Outputs
Connecting the Relay Outputs Each TN-5916 router has two sets of relay outputs—relay output 1 and relay output 2.The M12 A-coded 5-pin male connector on the TN-5916 front panel is used for the two relay outputs. Use a power cord with an M12 A-coded 5-pin female connector to connect the relay contacts. - Page 11 M12 (4-pin, M) to M12 (4-pin, M) Cross-Over Cable Wiring M12 (4-pin, M) to M12 (4-pin, M) Straight-Through Cable Wiring M12 (4-pin, M) to RJ45 (8-pin) Cross-Over Cable Wiring M12 (4-pin, M) to RJ45 (8-pin) Straight-Through Cable Wiring - 11 -...
-
Page 12: Bypass Relay Function
Bypass Relay Function The TN-5916 is equipped with a bypass relay function. When the router is operating normally, these bypass ports work in the same way as the other ports. That is, frame ingressions are processed and then forwarded. If the router stops working due to a power failure, the bypass relay function will be triggered to ensure non-stop data communication. -
Page 13: Led Indicators
LED Indicators Several LED indicators are located on the ToughNet router’s front panel. The function of each LED is described in the table below. Color State Description System LEDs Power is being supplied to power input PWR1. PWR1 AMBER Power is not being supplied to power input PWR1 Power is being supplied to power input PWR2. -
Page 14: Specifications
Specifications Technology Standards IEEE 802.3 for 10BaseT IEEE 802.3u for 100BaseT(X) IEEE 802.3x for Flow Control IEEE 802.1D for Spanning Tree Protocol IEEE 802.1w for Rapid STP IEEE 802.1Q for VLAN Tagging IEEE 802.1p for Class of Service IEEE 802.3ad for static Port Trunk Protocols IGMPv1/v2, SNMPv1/v2c/v3, DHCP Server, TFTP, SNTP, SMTP, RMON, HTTP, HTTPS, Telnet,... - Page 15 Environmental Limits Operating Temperature -40 to 75°C (-40 to 167°F) Storage Temperature -40 to 85°C (-40 to 185°F) Operating Humidity 5 to 95% (non-condensing) Regulatory Approvals Safety UL/cUL 508, EN 60950-1 (LVD) EN 55032, EN 55024 CISPR 32, FCC Part 15B Class A IEC 61000-4-2 ESD: Contact 6 kV;...
Need help?
Do you have a question about the ToughNet TN-5900 Series and is the answer not in the manual?
Questions and answers