Revision History Revision Release Date Description of Change(s) March 04, 2024 Initial release...
Page 3
NuPRO-E47 Preface Copyright 2024 ADLINK Technology, Inc. This document contains proprietary information protected by copy- right. All rights are reserved. No part of this manual may be repro- duced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.
Page 4
Conventions Take note of the following conventions used throughout this manual to make sure that users perform certain tasks and instructions properly. Additional information, aids, and tips that help users perform tasks. NOTE: NOTE: Information to prevent minor physical injury, component dam- age, data loss, and/or program corruption when trying to com- plete a task.
64GB on two DIMM slots. These advanced features, coupled with PCI Express® x16 expan- sion capability, dual PCI Express®-based Gigabit Ethernet, SATA 6 Gb/s and USB 3.2 support make the NuPRO-E47 ideal for vision and automation control applications. 1.2 Features ...
Watchdog timer, hardware monitor Optional HD audio kit (DB-Audio2 daughter board) TPM2.0 RoHS compliant To purchase the optional DB-Audio2 daughter board, please contact your ADLINK sales representative. NOTE: NOTE: 1.3 Specifications Processor& System Intel® Core™ i9-12900E, up to 5.0 GHz, 16 Cores, 30M Cache, 65W TDP Intel®...
Page 13
NuPRO-E47 Memory Dual channel DDR5 4800 MHz, up to 64GB AMI® UEFI BIOS BIOS 256 Mbit SPI flash memory Infineon TPM SLB 9670XQ2.0 or 9670VQ2.0 1-255 sec. or 1-255 min. software programmable, can generate system reset Hardware CPU temperature, system temperature, system voltage, CPU...
Display Integrated Intel® HD series, based on CPU Graphics for different GPU 1x VGA on rear I/O, resolution up to 1920 x 1200@60Hz 1x DVI-D via onboard pin header, resolution DVI-D up to 1920 x 1200@60Hz 1x HDMI on rear I/O, resolution up to 4096 x HDMI 2160 @ 60Hz Ethernet...
HDMI Port Pin # Signal Pin # Signal HDMI0_P2 HDMI0_CKN HDMI0_N2 TP_HDMI0_CEC DMI0_P1 HDMI0_SCL_SNK HDMI0_N1 HDMI0_SDA_SNK HDMI0_P0 P_+5V_S0_HDMI0 HDMI0_N0 HDMI0_HPD_SNK HDMI0_CKP 1.8 Board Layout Figure 1-4: Board Layout Connector Description CN40 DIMM B0 CN38 DIMM A0 FAN1 CPU fan header M2M1 M.2 M Key Introduction...
Page 21
NuPRO-E47 Connector Description CN35 System panel header CN22 COM #1 COM #2 COM #3 CN10 COM #4 CN43 SATA #5 CN44 SATA #6 CN32 SATA #3 CN33 SATA #4 CN30 SATA #1 CN31 SATA #2 CN26 USB3.0 #4/5 CN27 USB3.0 #6/7 CN28 USB3.0 #8/9...
1.9 Onboard Connectors COM #1 to #4 Connector (RS-232) (CN7/8/9/10) Pin # RS-232 Signal COM#1 COM#2 COM#3 COM#4 Connector CN10 Pitch 2.00 mm 2.00 mm 2.00 mm 2.00 mm COM #1 to #2 Connector (RS-422/485) (CN7/8) Pin # RS-422 RS-485 TXD- Data- TXD+...
Page 25
NuPRO-E47 VGA Header (VGA1) Pin # Signal Pin # Signal Green DDC_DAT Blue DDC_CLK HSYNC VSYNC ATX 12V Power Connector (CN36) Pin # Signal +12V DC +12V DC Serial SATA Connectors (CN30 to 33, CN43, CN44) Pin # Signal Introduction...
Page 26
Audio Header (CN5) This connector is designed for use with the ADLINK DB-Audio2 daughter board. Pin # Signal Function Ground AUD_BCLK Audio Clock Ground ICH_AUD_SDIN1 Audio Data Input + 5V ICH_AUD_SDOUT Audio Data Output P5V_AUD + 5V P3V3_DVDD 3.3V AUD_SYNC Audio Synchronous AUD_RSTJ Audio Reset...
Page 27
NuPRO-E47 System Panel Header (CN35) Connects to chassis-mounted buttons, speakers, and LEDs. Pin # Signal SPKR RSTBTN +5V_PSU PWRBTN KEYLOCK HLED PLED HLED_POWER +5V_PSU Fan Header (FAN1, FAN2) Pin # Signal Fan power (+12V) Fan Tachometer Fan Speed Control Introduction...
Page 28
LTP Header (CN22) Pin # Signal Pin # Signal STB-L AFD-L ERR-L INIT-L ACK-L SLIN-L BUSY SLCT Introduction...
1.10 Jumpers & Switches Clear CMOS Jumper (CN41) To clear the BIOS settings (RTC RST#): 1. Power down and disconnect power from the system. 2. Short pins 2-3 on CN41. 3. Reconnect power and power up the system. 4. Wait 3 seconds or more. 5.
2-port COM cable with bracket (2.0 mm pitch) Printer port cable with bracket (2.0 mm pitch) The NuPRO-E47 must be protected from static discharge and physical shock. Never remove any of the socketed parts except at a static-free workstation. Use the anti-static bag shipped with WARNING: the product to handle the board.
NuPRO-E47 Appendix A BIOS Setup The following chapter describes basic navigation for the ® AMIBIOS EFI BIOS setup utility. A.1 Entering the BIOS To enter the setup screen, follow these steps: 1. Power on the motherboard 2. Press < Delete > when the prompt appears: A.2 Menu Structure...
Page 36
Main Advanced Chipset Security ► CPU ► System Agent - System Date - Administrator - System Time Configuration (SA) Password ► Power Configuration - User Password ► PCH-I/O ► Secure Boot Management ► Serial Console Configuration menu ► Security Redirection - PCH digital I/O ►...
NuPRO-E47 Boot Save & Exit MEBx - Setup Prompt - Save Changes - Intel(R) ME Timeout and Exit Password - Bootup - Discard NumLock State Changes and Exit - Quiet Boot - Save Changes - Fast Boot and Reset - Boot Option #1...
A.4 Advanced Menu This menu contains the settings for most of the user interfaces in the system. Feature Description ► CPU Configuration CPU Configuration ► Power Management System ACPI Parameters ► Serial Console Redirection Serial Console Redirection ► USB Configuration USB Configuration Parameters ►...
Page 39
NuPRO-E47 Feature Option Description Number of P-cores to enable in each processor package. Note: Number of Active Cores and E-cores are looked at Performance-cores together. When both are {0,0}, Pcode will enable all cores. Intel (VMX) Enabled When enabled, a VMM can utilize...
A.4.2 Power Management Feature Option Description ATX Mode Select Emulation AT or ATX function. Emulate AT If this option set to [Emulation AT], Mode BIOS will report no suspend functions (S3 & S4) to ACPI OS. In Power Supply Unit windows XP, it will make OS show shutdown message during system shutdown.
Page 41
NuPRO-E47 Feature Option Description ANSI Emulation: ANSI: Extended ASCII VT100 char set. VT100: ASCII char set. VT100Plus VT100Plus: Extends VT100 to Terminal Type VT-UTF9 support color, function keys, etc. VT- UTF8: Uses UTF8 encoding to map Unicode chars onto 1 or more bytes.
Feature Option Description None Flow control can prevent data loss Hardware from buffer overflow. When sending RTS/CTS data, if the receiving buffers are full, a 'stop' signal can be sent to stop the Flow Control data flow. Once the buffers are empty, a 'start' signal can be sent to re-start the flow.
NuPRO-E47 Feature Option Description 20 sec The time-out value for Control, Bulk, USB transfer time- 1 sec and Interrupt transfers. 5 sec 10 sec 20 sec USB mass storage device Start Unit Device reset time- 10 sec command time-out. 30 sec...
Feature Option Description Enabled Enable or Disable Platform Hierarchy Platform Hierarchy Disabled Enabled Enable or Disable Storage Hierarchy Storage Hierarchy Disabled Endorsement Enabled Enable or Disable Endorsement Hierarchy Disabled Hierarchy Select to Tell O.S. to support PPI Physical Presence Spec Version 1.2 or 1.3. Note some Spec Version HCK tests might not support 1.3.
Page 45
NuPRO-E47 Feature Option Description Enabled Enable or Disable Parallel Port Parallel Port Disabled (LPT/LPTE) Auto Select an optimal settings for IO=378h; IRQ=5; Super IO Device IO=378h; IRQ=5,6,7,9,10,11,12; Change Settings IO=278h; IRQ=5,6,7,9,10,11,12; IO=3BCh; IRQ=5,6,7,9,10,11,12; STD Printer Mode Change the Printer Port Mode SPP Mode EPP-1.9 and SPP...
A.4.7 NCT6126H Hardware Monitor Feature Option Description SMART FAN IV Configure Fan Control Mode. Select Manual mode Manual Mode, user can configure a fix fan duty. Select SMART FAN IV, CPU Fan Control user can configure 4 temperatures Mode(Fan 1) and 4 fan duties.
NuPRO-E47 Feature Option Description The value of Fan Duty/RPM when FD/PRM 1 temperature is T1. Temperature 2 The value of temperature2. The value of Fan Duty/RPM when FD/PRM 2 temperature is T2. Temperature 3 The value of temperature3. The value of Fan Duty/RPM when FD/PRM 3 temperature is T3.
A.5 Chipset Feature Option Description ► System (SA) System Agent (SA) Parameters Configuration ► PCH-IO PCH Parameters Configuration Disabled Disable/Enable ACPI GPIO Device PCH digital I/O Enabled support for PCH digital I/O and user device A.5.1 System Agent (SA) Configuration Feature Option Description...
Page 53
NuPRO-E47 A.5.1.1 Graphic Configuration Feature Option Description IGFX Select which of IGFX/PEG/PCI Auto Graphics device should be Primary Primary Display PEG Slot Display or select HG for Hybrid Gfx. PCH PCI Enabled Keep IGFX enabled based on the Internal Graphics Auto setup options.
Feature Option Description Enable VMD Global Enabled Enable/Disable to VMD Global Mapping Disabled Mapping Enabled Enable/Disable RAID0 support RAID0 Disabled Enabled Enable/Disable RAID1 support RAID1 Disabled Enabled Enable/Disable RAID5 support RAID5 Disabled Enabled Enable/Disable RAID10 support RAID10 Disabled Intel Rapid Enabled Enable/Disable Intel Rapid Recovery Recovery...
Page 55
NuPRO-E47 A.5.2.1 SATA Configuration Feature Option Description SATA Mode AHCI Determines how SATA controller(s) Selection operate. Gen3 Indicates the maximum speed the SATA Controller Default SATA controller can support. Speed Gen1 Gen2 Enabled Enable or Disable SATA Port SATA HDD 0...
Page 56
Feature Option Description USB SS Physical Enabled Enable/Disable this USB Physical Connector #0 Disabled Connector (physical port). Once disabled, any USB devices plug into USB SS Physical Enabled the connector will not be detected by Connector #1 Disabled BIOS or OS. USB SS Physical Enabled Connector #2...
NuPRO-E47 Feature Option Description USB HS Physical Enabled Enable/Disable this USB Physical Connector #0 Disabled Connector (physical port). Once disabled, any USB devices plug into USB HS Physical Enabled the connector will not be detected by Connector #1 Disabled BIOS or OS.
Feature Option Description ► Secure Boot Secure Boot configuration menu ► Security Security Configuration settings Configuration A.6.1 Secure Boot menu Feature Option Description Secure Boot feature is Active if Disabled Secure Boot is Enabled, Platform Enabled Secure Boot key (PK) is enrolled and the system Control is in User mode.
NuPRO-E47 A.7 Boot Feature Option Description Number of seconds to wait for setup Setup Prompt activation key. The maximum value Timeout is 8. Bootup NumLock Select the keyboard NumLock state State Enables or disables Quiet Boot Enabled Quiet Boot option...
Page 60
Feature Option Description NVME Sets the system boot order Hard Disk UEFI AP CD/DVD USB Hard Disk Boot Option #2 USB CD/DVD USB Key USB Floppy USB Lan Network Disabled UEFI AP Sets the system boot order Hard Disk NVME CD/DVD USB Hard Disk Boot Option #3...
Page 61
NuPRO-E47 Feature Option Description Sets the system boot order Hard Disk NVME UEFI AP CD/DVD USB Hard Disk Boot Option #5 USB CD/DVD USB Key USB Floppy USB Lan Network Disabled USB Hard Disk Sets the system boot order Hard Disk...
Page 62
Feature Option Description USB Key Sets the system boot order Hard Disk NVME UEFI AP CD/DVD Boot Option #8 USB Hard Disk USB CD/DVD USB Floppy USB Lan Network Disabled USB Floppy Sets the system boot order Hard Disk NVME UEFI AP CD/DVD Boot Option #9...
NuPRO-E47 Feature Option Description Network Sets the system boot order Hard Disk NVME UEFI AP CD/DVD Boot Option #11 USB Hard Disk USB CD/DVD USB Key USB Floppy USB Lan Disabled A.8 Save & Exit Feature Description Save Changes and Exit system setup after saving the changes.
Feature Description Save as User Save the changes done so far as User Defaults. Defaults Restore User Restore the User Defaults to all the setup options Defaults Launch EFI Shell Attempts to Launch EFI Shell application (Shell.efi) from file system from one of the available file system devices device A.9 MEBx...
NuPRO-E47 Important Safety Instructions For user safety, please read and follow all instructions, WARNINGS, CAUTIONS, and NOTES marked in this manual and on the associated equipment before handling/operating the equipment. Read these safety instructions carefully. Keep this user’s manual for future reference.
Page 66
Never attempt to fix the equipment. Equipment should only be serviced by qualified personnel. A Lithium-type battery may be provided for uninterrupted, backup or emergency power. Risk of explosion if battery is replaced with one of an incorrect type. Dispose of used batteries appropriately. WARNING: ...
Need help?
Do you have a question about the NuPRO-E47 and is the answer not in the manual?
Questions and answers