Denon AVR-2809CI Owner's Manual page 28

Step 2 : Measurement
F Menu screen F
q
Auto Setup
Audyssey MultEQ XT
Auto Setup
Step2:Measurement
Please place microphone
Step2:Measurement
at ear height at
Now measuring 2nd
2nd listening position.
listening position.
Next
Calculate
Cancel
w
Auto Setup
Audyssey MultEQ XT
Auto Setup
Step2:Measurement
Please place microphone
Step2:Measurement
at ear height at
All the measurements
3rd listening position.
were finished.
Next
Calculate
Retry
Cancel
q Select "Next 0", then press .
o
• The measurement of the 2nd position starts.
• Select "Calculate 0" with i , and press
w Move the microphone to the 3rd position and press
• The measurement of the 3rd position starts.
• Select "Calculate 0" with i , and press
e P erform repeatedly through the 6th position or more. A maximum
of 8 position can be measured .
r " All the measurements were fi nished." is displayed on the on-
screen display, when you have completed measurements in 8th
positions.
• Select "Calculate 0", and press to proceed to Step 3.
o
n To cancel Auto Setup
Press ui to select "Cancel 0", then press
After completing a measurement position, move the microphone to
the next position.
Measure at least 6 positions: the main listening position and 5 other
surrounding positions. Although it is allowable to measure less than 6
positions, it is recommended to measure 6 or more positions (with a
maximum of 8 positions) for best results.

Step 3 : Calculation
F Menu screen F
q w
Audyssey MultEQ XT
Front L
Cancel
The values obtained from the measurements are automatically
r
analyzed and the attributes for each of the speakers in the listening
area are determined.
Audyssey MultEQ XT
q Select "Calculate 0" at Step 2, then press
• Analysis begins.
• Analysis takes several minutes to complete.
Calculate
Retry
• The time required for this analysis depends on the number of
Cancel
speakers connected. The greater the number of speakers connected,
the longer analysis will take.
NOTE
o to proceed to Step 3.
• Do not change the speaker connections or subwoofer volume,
o .
or speaker locations after making measurements. If changes are
necessary, make the changes and use Audyssey MultEQ XT auto
o to proceed to Step 3.
setup once again for an updated EQ solution.
• For instance, if the location or direction of a speaker is altered, the
Auto Setup should be performed again to ensure the correct EQ
solution for the new room confi guration.
o .
q
Auto Setup
Audyssey MultEQ XT
Step3:Calculation
Calculating
Please wait...
– – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – –
.
o
Step 4 : Check
F Menu screen F
q
Auto Setup
Audyssey MultEQ XT
Step4:Check
Please check the results
of the measured item.
Speaker Config.Check
Distance Check
Channel Level Check
Crossover Freq.Check
Next
When analysis is complete, check the analysis results for the following
four items.
q Make your selection using u i and press
• Presence and size of speaker
"Speaker Confi g. Check"
• Distance of speaker from listening position
"Distance Check"
• Speaker channel level
"Channel Level Check"
• Crossover Frequency
"Crossover Freq. Check"
ui to change which speaker is displayed.
w Use
RETURN
e Press .
This returns you to analysis results items, so repeat step q.
r Press i to select "Next 0", and then press
5.
Distance values that are greater than the actual distance of a speaker
may be accurate for speakers with built-in fi lters (subwoofers, etc).
This is because these fi lters add electrical delay (distance) to the signal
that is compensated for by the Auto Setup process.
ENTER
.
o to proceed to Step