Advertisement
SERVICE MANUAL
EN
It is the Customer's responsibility to have all operators and service personnel read and understand this manual.
Contact your local DeVilbiss representative for additional copies of this manual.
READ ALL INSTRUCTIONS BEFORE OPERATING THIS DEVILBISS PRODUCT.
SB-2-546-R1 (5/2018)
COMPACT-CONVENTIONAL
GRAVITY FEED SPRAYGUN
IMPORTANT! DO NOT DESTROY
1 / 10
www.carlisleft.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Carlisle DeVILBISS COM-G430-14-02
Summary of Contents for Carlisle DeVILBISS COM-G430-14-02
- Page 1 SERVICE MANUAL COMPACT-CONVENTIONAL GRAVITY FEED SPRAYGUN IMPORTANT! DO NOT DESTROY It is the Customer's responsibility to have all operators and service personnel read and understand this manual. Contact your local DeVilbiss representative for additional copies of this manual. READ ALL INSTRUCTIONS BEFORE OPERATING THIS DEVILBISS PRODUCT. SB-2-546-R1 (5/2018) 1 / 10 www.carlisleft.com...
-
Page 2: Safety Warnings
SAFETY WARNINGS FIRE AND EXPLOSION Solvents and coating materials can be highly flammable or combus- tible when sprayed. ALWAYS refer to the coating material suppliers instructions and COSHH sheets before using this equipment. IMPORTANT: Read and follow all instruc- tions and SAFETY PRECAUTIONS before using this equipment. -
Page 3: Parts List
Patent No. 2372465 (GB) GFC-502 GFC-501 1 Liter 20 oz. (SB-4-043) (SB-4-261) MODEL PART NUMBER PARTS LIST Example: COM-G430-14-02 Ref. Description Part Number Qty. Options Aircap Air Cap/Retaining ring COM-430 SP-100-430-K Fluid Nozzle SP-200S-**-K 14, 18, 22 e.g ** =14 =1.4 mm Fluid nozzle size Separator SP-626-K5... -
Page 4: Specification
OPERATION PREVENTATIVE MAINTENANCE SPECIFICATION Mix coating material to manufac- Turn off air and relieve pressure in Air supply connection: turers instructions. the supply lines, or if using QD Universal 1/4" BSP and NPS system, disconnect from airline. Fill the cup with the required amount of material. - Page 5 Remove Adjusting Knob (7), Loosen Housing (10). Remove Housing (10) and Spring (8), and Needle (9). Airvalve Spring. Remove Valve (11). Using Service Tool SPN-7, Remove Valve Seat. engage groove behind the Valve Seat. Push out the Front Airvalve Turn the Gun upside down Fit New Front Seal to Service Seal with a finger.
- Page 6 12. Fit Valve Seat to Gunbody. 13. Remove Rear Airvalve Seal 14. Fit new Seal to Service Tool. from housing (10) with a hooked instrument. 15. Fit Seal to Housing (10). 16. Replace Valve (11). 17. Replace Valve Spring and screw in Housing (10).
- Page 7 TROUBLESHOOTING CONDITION CAUSE CORRECTION Horn holes plugged. Clean. Ream with non-metallic point. Heavy top or Clean. bottom pattern Obstruction on top or bottom of fluid tip. Cap and/or tip seat dirty. Clean. Left or right side horn holes plugged. Clean. Ream with non-metallic point. Heavy right or left Dirt on left or right side of fluid tip.
- Page 8 TROUBLESHOOTING (continued) CONDITION CAUSE CORRECTION Fluid dripping or leaking from Cup loose on gun. Tighten. bottom of cup Cup gasket worn or missing below cup. Replace cup gasket. Cup threads dirty. Clean. Runs and sags Too much material flow. Adjust gun or reduce fluid flow. Material too thin.
- Page 9 ACCESSORIES HAV-500 OR Cleaning Brushes HAF-507 29-3100-K6 Scrubs GFC-501 (Acetal) 20 Oz. Cup ® 42884-214-K5 (3/8") Hand Cleaner Towels HAV-501 Whirlwind™ GFC-502 (Aluminum) 1-Liter Cup 42884-215-K10 (5/8") Gravity Feed Cups Adjusting Valve In-Line Air Filter (HAV-501 SHOWN) These gravity feed cups are designed to be used with EXL, FLG, GFG, GFHV, GTI or Compact...
-
Page 10: Warranty Policy
This product is covered by Carlisle Fluid Technologies’ materials and workmanship limited warranty. The use of any parts or accessories, from a source other than Carlisle Fluid Technologies, will void all warranties. Failure to reasonably follow any maintenance guidance provided may invalidate any warranty.
Need help?
Do you have a question about the DeVILBISS COM-G430-14-02 and is the answer not in the manual?
Questions and answers