Related Manuals for Yetter 5000-090A Series
Summary of Contents for Yetter 5000-090A Series
- Page 1 5000-090A SINGLE ROW SERIES STALK DEVASTATOR OWNER’S MANUAL PART IDENTIFICATION 2565-972-Rev-B ● 08/2024 YETTER MANUFACTURING CO. Founded 1930 Colchester, IL 62326 Toll free: (800)447-5777. Fax: (309)776-3222 Website: yetterco.com E-mail: info@yetterco.com...
- Page 2 It is the user’s responsibility to deliver his machine to the Yetter dealer who sold him the product for service or replacement of defective parts, which are covered by the warranty policy.
-
Page 3: Safety Precautions
SAFETY PRECAUTIONS A brief description of signal words that may be used in this manual: DANGER: Indicates an imminently hazardous situation which, if not avoided “will” result in death or serious injury. This signal word is to be limited to the most extreme situations. WARNING: Indicates a potentially hazardous situation which, if not avoided, “could”... - Page 4 PLEASE READ, VERY IMPORTANT SECURE CORN HEADER AGAINST UNWANTED LOWERING BY APPLYING THE LOCKING MECHANISM ON THE HYDRAULIC CYLINDERS! 1. Attach head to combine, lock head to combine 2. Raise the head off the ground and engage safety stop on the feeder house cylinder.
- Page 5 PLEASE READ, VERY IMPORTANT Subject to the size and weight of the corn header, one or two additional hydraulic cylinders may be required. The combine manufacturer generally keeps corresponding kits readily available for dealers. Subject to the design of the corn header and the carrying capacity of different combines, the steering axle may require the fitting of additional weights and the rear tires be filled with ballast.
-
Page 6: Bolt Torque
TABLE OF CONTENTS FOREWARD............2 WARRANTY............2 SAFETY INFORMATION........ 2 – 5 TORQUE …………………………........ 6 ASSEMBLY INSTRUCTIONS......7 – 8 LOCK UP / OPERATION.........8--9 PART IDENTIFICATION........10 BOLT TORQUE Important: Over-tightening hardware can cause just as much damage as under-tightening. Tightening hardware beyond the recommended range can reduce its shock load capacity. - Page 7 ASSEMBLY INSTRUCTIONS Step 1: Attach 5000-147 torsion pivot to frame using 2) 5000-420 clamp straps & 4) 2502-805 M16 bolts or 4) 2502-806 bolts. Step 2: Attach the 5000-292 torsion arm to the torsion pivot assemblies. Place 1) 5000-469 security cap over the 2502-430 ¾ X 8 bolt, slide bolt with cap through 1) 5000-292 torsion arm, then the torsion pivot, slide another 5000-292 torsion arm over bolt followed by another security cap, and then fasten the 2520-604 ¾...
-
Page 8: Operation
LOCK UP To “lock up” the Devastator roller, install a rod through the hole in the bottom of the torsion mount bracket, in front of the pivot arms. A Lock Pin can be ordered to lock up the devastators, 3841-302. OPERATION CORN HEAD ANGLE NEEDS TO BE ADJUSTED BETWEEN 23 –... - Page 9 BEARING REPLACEMENT/MAINTENANCE Put the bearing housing in a vice, use a pry bar to turn the bearing in the housing parallel with the slots, remove the old bearing, insert the new bearing in the slots, use a pry bar to move back to position, & grease until a small amount comes out between outer race &...
- Page 10 5000-090 PART IDENTIFICATION ITEM PART # DESCRIPTION QUANTITY 2502-353 ½-13 X 2 ½ HHCS GR 8 ZP 2502-430 ¾ - 10 X 8 HHCS GR 8 ZP 2502-805 M16 X 2 X 120 HEX FLANGE BOLT W/ THRD LOCK ZP 2502-806 M16 X 2 X 110 HEX FLANGE BOLT W THRD LOCK ZP 2520-357...
- Page 12 2565-972-Rev-B – 08/2024...
Need help?
Do you have a question about the 5000-090A Series and is the answer not in the manual?
Questions and answers