Page 2
WARRANTY Yetter Manufacturing warrants all products manufactured and sold by it against defects in material. This warranty being expressly limited to replacement at the factory of such parts or products as shall appear to be defective after inspection.
Page 3
BE ALERT! YOUR SAFETY IS INVOLVED. WATCH FOR THIS SYMBOL. IT POINTS OUT IMPORTANT SAFETY PRECAUTIONS. IT MEANS “ATTENTION---BECOME ALERT!” It is your responsibility as an owner, operator, or supervisor to know and instruct everyone using this machine at the time of initial assignment and at least annually thereafter, of the proper operation, precautions, and work hazards which exist in the operation of the machine in accordance with OSHA regulations.
Page 4
PLEASE READ, VERY IMPORTANT SECURE CORN HEADER AGAINST UNWANTED LOWERING BY APPLYING THE LOCKING MECHANISM ON THE HYDRAULIC CYLINDERS! 1. ATTACH HEAD TO COMBINE, LOCK HEAD TO COMBINE 2. RAISE THE HEAD OFF THE GROUND AND ENGAGE THE SAFETY STOP ON THE FEEDER HOUSE CYLINDER. 3.
Page 5
PLEASE READ, VERY IMPORTANT Subject to the size and weight of the corn header, one or two additional hydraulic cylinders may be required. The combine manufacturer generally keeps the corresponding kits readily available for the dealer. Subject to the design of the corn header and carrying capacity of the different combines, the steering axle may require the fitting of additional weights and the rear tires might need to be filled with ballast.
Page 6
TABLE OF CONTENTS INTRODUCTION ….…………………………………….....2 WARRANTY ……………………….…………………………..2 SAFETY INFORMATION ...…..…………………...…..3 – 5 TABLE OF CONTENTS / TORQUE / TOOLS NEEDED..6 PART PICTORIAL LIST / BILL OF MATERIALS... 7 – 9 ASSEMBLY INSTRUCTIONS 5000-022A ..…………………..……....10 – 14 5000-033A ..…………..........15 – 19 OPERATION / STORAGE / LOCK UP.……..…………….20 PARTS IDENTIFICATON 5000-022A ..……………………………..……..…..21 –...
Page 7
BEFORE INSTALLATION BEGINS, PLEASE CHECK THAT ALL PARTS WERE RECEIVED BY GOING THROUGH THE CRATE AND SORTING THE PARTS!!! 5000-022B for Lexion C512-30 / Capello Parts List 8) 5000-136, 8) 5000-137, 8) 5000-138, 1) 5000-177, 4) 5000-211B, 8) 5000-250, 4) 5000-254, 4) 5000-256, 4) 5000-259, 8) 5000-355 5000-033A for Lexion C508-30 / Capello Parts List –...
Page 8
PICTORIAL PART LIST 5000-136 Hardware Bag 2502-325 - 5/8-11 X 3 HHCS GR 5 ZP – QTY 1 2502-353 – ½-13 x 2 ½, HHCS, GR8, ZP – QTY 3 2510-121 - 5/8 DIA. SHLDR, 2-1/4 L SHLDR, ½-13 QTY 1 2520-357 - 1/2-13 LOCK HEX NUT, GR A, ZP –...
Page 9
PICTORIAL PART LIST 5000-137 Hardware Bag 2502-396 - 5/8-11 X 7 HHCS GRADE 8 ZP – QTY 4 2505-345 - 1/2-13 X 2 CAR BLT GR5 ZP – QTY 2 2520-361 - 1/2-13FLANGE WHZLCK HXNT, GR 5, ZP - QTY 2 2520-459 - 5/8-11 LOCK HEX NUT, GR A, ZP –...
Page 10
5000-022B ASSEMBLY INSTRUCTIONS (LEXION C512-30 / CAPELLO) Note: Before starting installation, clean the corn head of debris, remove the guards, & lift the snouts. Step 1: Attach the 5000-250 mount brackets to the frame using the 4) 5/8 x 7” bolts, mounting straps, & 5/8 lock hex nuts.
Page 11
5000-022B ASSEMBLY INSTRUCTIONS Step 2: Attach the 5000-309 support straps using the ½” x 2” carriage bolts & ½ flange lock nuts, tighten. Step 3: Install the 5000-323 lock-up pin in the storage location on the mount brackets. Secure with the hairpin clips.
Page 12
5000-022B ASSEMBLY INSTRUCTIONS Step 4: Attach the pivot arms, using the lower of the 2 holes, to the mount brackets using the 5/8” X 3 bolts, pivot bushings, and lock hex nuts. Tighten this hardware. Step 5: Install the push rods into the mount brackets then attach to the pivot arms with the 5/8”...
Page 13
5000-022B ASSEMBLY INSTRUCTIONS Step 6: Secure the mounting bracket installed in Step 1 at this time by tightening the 5/8 X 7” bolts & 5/8 lock nuts. Make sure the compression spring clears the cylinder channel, gathering chains, & deck plate adjustment.
Page 14
5000-022B ASSEMBLY INSTRUCTIONS Step 7: Install the Roller Arm Mount Tube inside the clamp channel of the pivot arms using the 5000- 138 bolt bag. Do not tighten this hardware until after the rollers have been installed in Step 8.
Page 15
5000-033A ASSEMBLY INSTRUCTIONS (LEXION C508-30 / CAPELLO) Note: Before starting installation, clean the corn head of debris, remove the guards, & lift the snouts. Step 1: Attach the 5000-250 mount brackets to the frame using the 5/8 x 7” bolts, mounting straps, & lock hex nuts. Mounting Brackets will be located under the snouts between rows 1 &...
Page 16
5000-033A ASSEMBLY INSTRUCTIONS Step 2: Attach the 5000-309 support straps using the ½” x 2” carriage bolts & flange lock nuts, tighten. Step 3: Install the 5000-323 lock-up pin in the storage location on the mount brackets. Secure with the hairpin clips.
Page 17
5000-033A ASSEMBLY INSTRUCTIONS Step 4: Attach the pivot arms, using the lower of the 2 holes, to the mount brackets using the 5/8” X 3 bolts, pivot bushings, & lock hex nuts. Tighten this hardware. Step 5: Install the push rods into the mount brackets then attach to the pivot arms with the 5/8”...
Page 18
5000-033A ASSEMBLY INSTRUCTIONS Step 6: Secure the mounting bracket installed in Step 1 at this time by tightening the 5/8 X 7” bolts & 5/8 lock nuts. Make sure the compression spring clears the cylinder channel, gathering chains, & deck plate adjustment.
Page 19
5000-033A ASSEMBLY INSTRUCTIONS Step 7: Install the Roller Arm Mount Tube inside the clamp channel of the pivot arms using the 5000- 138 bolt bag. Do not tighten this hardware until after the rollers have been installed in Step 8. Step 8: Insert the shim washer over the shaft on each end of the roller.
Page 20
OPERATION CORN HEAD ANGLE SHOULD BE BETWEEN 23 – 25° FOR OPTIMUM DEVASTATATOR PERFORMANCE. USE THE 5000-455 TO CHECK CORN HEAD ANGLE: Put the combine on a level surface. Lower the Corn head to your normal working head height. Place the magnetic protractor on the stripper plate to get the angle.
Page 21
5000-022B PARTS IDENTIFICATION ITEM PART # DESCRIPTION 2502-325 5/8” – 11 X 3” HHCS GR 5 ZP 2502-353 ½” – 13 X 2 ½” HHCS GR 8 ZP 2502-365 ½ - 13 X 3 ¾ HHCS GR 5 ZP 2502-396 5/8 –...
Page 23
5000-033A PARTS IDENTIFICATION ITEM PART # DESCRIPTION 2502-325 5/8 – 11 X 3 HHCS GR 5 ZP 2502-353 ½ - 13 X 2 ½ HHCS GR 8 ZP 2502-365 ½ - 13 X 3 ¾ HHCS GR 5 ZP 2502-396 5/8 –...
Page 25
TROUBLSHOOTING ISSUE CAUSE CORRECTIVE ACTION Residue 1. Incorrect Head Angle 1. Adjust head angle to 23 – 25 degrees (see page 20) Plugging 2. Roller Mount Tube incorrectly 2. Make sure the Bearing Support Tab is on the installed backside of the Roller Mount Tube 3.
Need help?
Do you have a question about the 5000-022B and is the answer not in the manual?
Questions and answers