Table of Contents
Advertisement
Quick Links
5000-022C Lexion C512-30 / Capello/ Claas
5000-033B Lexion C508-30 / Capello/ Claas
YETTER MANUFACTURING CO.
FOUNDED 1930
Colchester, IL 62326-0358
Toll free: 800/447-5777
309/776-3222 (Fax)
Website:
www.yetterco.com
E-mail:
info@yetterco.com
5000 SERIES
STALK
DEVASTATOR
CORN STALK ROLLER
*PATENTED*
OPERATOR'S MANUAL
PART IDENTIFICATION
2565-783_REV_D – 02/2024
Advertisement
Table of Contents
Related Manuals for Yetter 5000-022C
Summary of Contents for Yetter 5000-022C
- Page 1 5000 SERIES STALK DEVASTATOR CORN STALK ROLLER *PATENTED* 5000-022C Lexion C512-30 / Capello/ Claas 5000-033B Lexion C508-30 / Capello/ Claas OPERATOR’S MANUAL PART IDENTIFICATION 2565-783_REV_D – 02/2024 YETTER MANUFACTURING CO. FOUNDED 1930 Colchester, IL 62326-0358 Toll free: 800/447-5777 309/776-3222 (Fax) Website: www.yetterco.com...
-
Page 2: Introduction
WARRANTY Yetter Manufacturing warrants all products manufactured and sold by it against defects in material. This warranty being expressly limited to replacement at the factory of such parts or products as shall appear to be defective after inspection. -
Page 3: Safety Information
BE ALERT! YOUR SAFETY IS INVOLVED. WATCH FOR THIS SYMBOL. IT POINTS OUT IMPORTANT SAFETY PRECAUTIONS. IT MEANS “ATTENTION---BECOME ALERT!” It is your responsibility as an owner, operator, or supervisor to know and instruct everyone using this machine at the time of initial assignment and at least annually thereafter, of the proper operation, precautions, and work hazards which exist in the operation of the machine in accordance with OSHA regulations. - Page 4 PLEASE READ, VERY IMPORTANT SECURE CORN HEADER AGAINST UNWANTED LOWERING BY APPLYING THE LOCKING MECHANISM ON THE HYDRAULIC CYLINDERS! 1. ATTACH HEAD TO COMBINE, LOCK HEAD TO COMBINE 2. RAISE THE HEAD OFF THE GROUND AND ENGAGE THE SAFETY STOP ON THE FEEDER HOUSE CYLINDER. 3.
- Page 5 PLEASE READ, VERY IMPORTANT Subject to the size and weight of the corn header, one or two additional hydraulic cylinders may be required. The combine manufacturer generally keeps the corresponding kits readily available for the dealer. Subject to the design of the corn header and carrying capacity of the different combines, the steering axle may require the fitting of additional weights and the rear tires might need to be filled with ballast.
-
Page 6: Table Of Contents
INTRODUCTION ….…………………………………….....2 WARRANTY ……………………….…………………………..2 SAFETY INFORMATION ...…..…………………...…..3 – 5 TABLE OF CONTENTS / TORQUE / TOOLS NEEDED..6 ASSEMBLY INSTRUCTIONS 5000-022C ..…………………..……....7 – 11 5000-033B ..…………..........12 – 16 OPERATION / STORAGE / LOCK UP.……..…………….17 PARTS IDENTIFICATON 5000-022C ..………………………..……..…..18 – 19 5000-033B ..……………………..………...…..20 – 21 TROUBLESHOOTING............22... -
Page 7: 5000-022C
5000-022C ASSEMBLY INSTRUCTIONS (LEXION C512-30 / CAPELLO) Note: Before starting installation, clean the corn head of debris, remove the guards, & lift the snouts. Step 1: Attach the 5000-250 mount brackets to the frame using the 4) 5/8 x 7” bolts, mounting straps, & 5/8 lock hex nuts. - Page 8 5000-022C ASSEMBLY INSTRUCTIONS Step 2: Attach the 5000-309 support straps using the ½” x 2” carriage bolts & ½ flange lock nuts, tighten. Step 3: Install the 5000-323 lock-up pin in the storage location on the mount brackets. Secure with the hairpin clips.
- Page 9 5000-022C ASSEMBLY INSTRUCTIONS Step 4: Attach the pivot arms, using the lower of the 2 holes, to the mount brackets using the 5/8” X 3 bolts, pivot bushings, and lock hex nuts. Tighten this hardware. Step 5: Install the push rods into the mount brackets then attach to the pivot arms with the 5/8”...
- Page 10 5000-022C ASSEMBLY INSTRUCTIONS Step 6: Secure the mounting bracket installed in Step 1 at this time by tightening the 5/8 X 7” bolts & 5/8 lock nuts. Make sure the compression spring clears the cylinder channel, gathering chains, & deck plate adjustment.
- Page 11 5000-022C ASSEMBLY INSTRUCTIONS Step 7: Install the Roller Arm Mount Tube inside the clamp channel of the pivot arms using the 5000- 138 bolt bag. Do not tighten this hardware until after the rollers have been installed in Step 8.
-
Page 12: 5000-033B
5000-033B ASSEMBLY INSTRUCTIONS (LEXION C508-30 / CAPELLO) Note: Before starting installation, clean the corn head of debris, remove the guards, & lift the snouts. Step 1: Attach the 5000-250 mount brackets to the frame using the 5/8 x 7” bolts, mounting straps, & lock hex nuts. Mounting Brackets will be located under the snouts between rows 1 &... -
Page 13: 5000-033B
5000-033B ASSEMBLY INSTRUCTIONS Step 2: Attach the 5000-309 support straps using the ½” x 2” carriage bolts & flange lock nuts, tighten. Step 3: Install the 5000-323 lock-up pin in the storage location on the mount brackets. Secure with the hairpin clips. - Page 14 5000-033B ASSEMBLY INSTRUCTIONS Step 4: Attach the pivot arms, using the lower of the 2 holes, to the mount brackets using the 5/8” X 3 bolts, pivot bushings, & lock hex nuts. Tighten this hardware. Step 5: Install the push rods into the mount brackets then attach to the pivot arms with the 5/8”...
- Page 15 5000-033B ASSEMBLY INSTRUCTIONS Step 6: Secure the mounting bracket installed in Step 1 at this time by tightening the 5/8 X 7” bolts & 5/8 lock nuts. Make sure the compression spring clears the cylinder channel, gathering chains, & deck plate adjustment.
- Page 16 5000-033B ASSEMBLY INSTRUCTIONS Step 7: Install the Roller Arm Mount Tube inside the clamp channel of the pivot arms using the 5000- 138 bolt bag. Do not tighten this hardware until after the rollers have been installed in Step 8. Step 8: Insert the shim washer over the shaft on each end of the roller.
-
Page 17: Operation / Storage / Lock Up
OPERATION CORN HEAD ANGLE SHOULD BE BETWEEN 23 – 25° FOR OPTIMUM DEVASTATATOR PERFORMANCE. USE THE 5000-455 TO CHECK CORN HEAD ANGLE: Put the combine on a level surface. Lower the Corn head to your normal working head height. Place the magnetic protractor on the stripper plate to get the angle. -
Page 18: Parts Identificaton 5000-022C
5000-022C PARTS IDENTIFICATION ITEM PART # DESCRIPTION 2502-325 5/8” – 11 X 3” CAP SCREW GRADE 5 2502-353 ½” – 13 X 2 ½” CAP SCREW GRADE 8 2502-365 ½ - 13 X 3 ¾ CAP SCREW GRADE 5 2502-396 5/8 –... - Page 19 5000-022C PARTS IDENTIFICATION...
- Page 20 5000-033B PARTS IDENTIFICATION ITEM PART # DESCRIPTION 2502-325 5/8 – 11 X 3 CAP SCREW GRADE 5 2502-353 ½ - 13 X 2 ½ CAP SCREW GRADE 8 2502-365 ½ - 13 X 3 ¾ CAP SCREW GRADE 5 2502-396 5/8 –...
- Page 21 5000-033B PARTS IDENTIFICATION...
-
Page 22: Troubleshooting
TROUBLESHOOTING ISSUE CAUSE CORRECTIVE ACTION Residue 1. Incorrect Head Angle 1. Adjust head angle to 23 – 25 degrees Plugging 2. Roller Mount Tube incorrectly 2. Make sure the Bearing Support Tab is on the installed backside of the Roller Mount Tube 3. - Page 24 2565-783_REV_D • 02/2024...