Advertisement
Quick Links
5000 SERIES STALK DEVASTATOR
5000-023B – 5000-024B – 5000-035A
Gleaner 3000 & 3308, Hugger 630/830, MF 3000 (1988 &
Newer), Challenger CH630 & CH830
YETTER MANUFACTURING CO.
FOUNDED 1930
Colchester, IL 62326-0358
Toll free: 800/447-5777
309/776-3222 (Fax)
Website:
www.yetterco.com
E-mail:
info@yetterco.com
CORN STALK ROLLER
*PATENTED*
OPERATOR'S MANUAL
PART IDENTIFICATION
2565-784_REV_C – 09/2019
Advertisement
Related Manuals for Yetter 5000-023B
Summary of Contents for Yetter 5000-023B
- Page 1 5000 SERIES STALK DEVASTATOR CORN STALK ROLLER *PATENTED* 5000-023B – 5000-024B – 5000-035A Gleaner 3000 & 3308, Hugger 630/830, MF 3000 (1988 & Newer), Challenger CH630 & CH830 OPERATOR’S MANUAL PART IDENTIFICATION 2565-784_REV_C – 09/2019 YETTER MANUFACTURING CO. FOUNDED 1930...
-
Page 2: Warranty
WARRANTY Yetter Manufacturing warrants all products manufactured and sold by it against defects in material. This warranty being expressly limited to replacement at the factory of such parts or products as shall appear to be defective after inspection. - Page 3 BE ALERT! YOUR SAFETY IS INVOLVED. WATCH FOR THIS SYMBOL. IT POINTS OUT IMPORTANT SAFETY PRECAUTIONS. IT MEANS “ATTENTION---BECOME ALERT!” It is your responsibility as an owner, operator, or supervisor to know and instruct everyone using this machine at the time of initial assignment and at least annually thereafter, of the proper operation, precautions, and work hazards which exist in the operation of the machine in accordance with OSHA regulations.
- Page 4 PLEASE READ, VERY IMPORTANT SECURE THE CORN HEADER AGAINST UNWANTED LOWERING BY APPLYING THE LOCKING MECHANISM ON HYDRAULIC CYLINDERS! 1. Attach head to combine, lock head to combine 2. Raise the head off the ground and engage safety stop on the feeder house cylinder 3.
- Page 5 SAFETY INFORMATION…………………………………..…….....3 – 4 TABLE OF CONTENTS……………………………………………………..5 TORQUE / TOOLS REQUIRED.……………………………………...…..5 ASSEMBLY INSTRUCTIONS …..…...…………………………..6 – 11 5000-023B & 5000-024B ....…...………..….....6 – 8 5000-035A..…...………..………..…......9 – 11 OPERATION / BEARING / STORAGE / LOCK UP...…..…..………..12 PARTS IDENTIFICATON..............13 – 21 5000-023B…………………………….…………….....…13 – 14 5000-024B……………………….…………………...…..15 –...
-
Page 6: 5000-023B & 5000-024B
5000-023B & 5000-024B ASSEMBLY INSTRUCTION GLEANER 3000 / HUGGER 630 & 830 / MF 3000 / CHALLENER CH630 & CH 830 STEP 1. Attach the 5000-248 Extension Mount to the 5000-247 Plate using 5/8” X 2” Bolts & 5/8” Lock Hex Nuts. - Page 7 5000-023B & 5000-024B ASSEMBLY INSTRUCTION STEP 3: Attach the 5000-135 Arm Mounts to the Extension Mount Bracket using ½” X 2” Bolts, ½” Washers, & ½” Lock Hex Nuts. STEP 4: Install the 5000-323 Lock Up Pin in the storage location on the mount arms, secure with Hair Pin Clips.
- Page 8 5000-023B & 5000-024B ASSEMBLY INSTRUCTION STEP 6: Install the push rods into the mount brackets & attach to the pivot arms using the 5/8” Shoulder Bolts. 5/8” Washers, & ½” Jam Nuts. Use the lower hole on the arm. The washers are to be installed on each side of the “Eye”...
- Page 9 5000-035A ASSEMBLY INSTRUCTION AGCO GLEANER 3308 STEP 1: Install the Mount Assemblies on the Corn Head Frame using 5/8” X 7” Bolts, Mount Straps, Clamp Brackets/Straps, 5/8” Washers, & 5/8” Lock Hex Nut. Place Mounts, Mount Straps, & Brackets as shown. The Double Mount goes between rows 4 &...
-
Page 10: 5000-035A
5000-035A ASSEMBLY INSTRUCTION STEP 3: Attach 1) 5000-135 Arm Mount on each Offset Mount using ½” X 1 ¾” Bolts, ½” Washers, & ½” Lock Hex Nuts. Attach 2 Arm Mounts to the Double Offset on rows 4 & 5. STEP 4: Install a 5000-323 Lock Up Pin in the storage location on the Mount Arms &... - Page 11 5000-035A ASSEMBLY INSTRUCTION STEP 6: Install each Push Rods into the Mount Bracket & attach to the Pivot Arms using 5/8” Shoulder Bolts, 5/8” Washers, & ½” Jam Lock Hex Nuts. Use the lower hole on the arm. The Washers are to be installed on each side of the “EYE”...
- Page 12 OPERATION CORN HEAD ANGLE SHOULD BE BETWEEN 23 – 25° FOR OPTIMUM DEVASTATATOR PERFORMANCE. USE THE 5000-455 TO CHECK CORN HEAD ANGLE: Put the combine on a level surface. Lower the Corn head to your normal working head height. Place the magnetic protractor on the stripper plate to get the angle.
- Page 13 5000-023B PARTS IDENTIFICATION **PART IDENTIFICATION TABLE ON THE FOLLOWING PAGE**...
- Page 14 5000-023B PARTS IDENTIFICATION...
- Page 15 5000-024B PARTS IDENTIFICATION **PART IDENTIFICATION TABLE ON THE FOLLOWING PAGE**...
- Page 16 5000-024B PARTS IDENTIFICATION...
- Page 17 5000-035A PARTS IDENTIFICATION **PART IDENTIFICATION TABLE ON THE FOLLOWING PAGE**...
- Page 18 5000-035A PARTS IDENTIFICATION...
- Page 19 TROUBLSHOOTING ISSUE CAUSE CORRECTIVE ACTION Residue 1. Incorrect Head Angle 1. Adjust head angle to 23 – 25 degrees (see page 12) Plugging 2. Roller Mount Tube incorrectly 2. Make sure the Bearing Support Tab is on the backside of installed the Roller Arm Mount Tube 3.
- Page 20 2565-784_REV_C • 09/19...
Need help?
Do you have a question about the 5000-023B and is the answer not in the manual?
Questions and answers