Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Yetter Manuals
  4. Farm Equipment
  5. 5000-023A
  6. Operator's manual

Yetter 5000-023A Operator's Manual

Stalk devastator corn stalk roller
Hide thumbs

Advertisement

Quick Links

Download this manual
YETTER MANUFACTURING CO.
FOUNDED 1930
Colchester, IL 62326-0358
Toll free: 800/447-5777
309/776-3222 (Fax)
Website:
www.yetterco.com
E-mail:
info@yetterco.com
5000 SERIES
STALK
DEVASTATOR
CORN STALK ROLLER
*PATENTED*
5000-023A & 5000-024A
5000-035
OPERATOR'S MANUAL
PART IDENTIFICATION
2565-784_REV_B – 12/2018

Advertisement

loading
Need help?

Need help?

Do you have a question about the 5000-023A and is the answer not in the manual?

Questions and answers

Related Manuals for Yetter 5000-023A

Summary of Contents for Yetter 5000-023A

  • Page 1 5000 SERIES STALK DEVASTATOR CORN STALK ROLLER *PATENTED* 5000-023A & 5000-024A 5000-035 OPERATOR’S MANUAL PART IDENTIFICATION 2565-784_REV_B – 12/2018 YETTER MANUFACTURING CO. FOUNDED 1930 Colchester, IL 62326-0358 Toll free: 800/447-5777 309/776-3222 (Fax) Website: www.yetterco.com E-mail: info@yetterco.com...
  • Page 2 WARRANTY Yetter Manufacturing warrants all products manufactured and sold by it against defects in material. This warranty being expressly limited to replacement at the factory of such parts or products as shall appear to be defective after inspection.
  • Page 3 BE ALERT! YOUR SAFETY IS INVOLVED. WATCH FOR THIS SYMBOL. IT POINTS OUT IMPORTANT SAFETY PRECAUTIONS. IT MEANS “ATTENTION---BECOME ALERT!” It is your responsibility as an owner, operator, or supervisor to know and instruct everyone using this machine at the time of initial assignment and at least annually thereafter, of the proper operation, precautions, and work hazards which exist in the operation of the machine in accordance with OSHA regulations.
  • Page 4 PLEASE READ, VERY IMPORTANT SECURE THE CORN HEADER AGAINST UNWANTED LOWERING BY APPLYING THE LOCKING MECHANISM ON HYDRAULIC CYLINDERS! 1. Attach head to combine, lock head to combine 2. Raise the head off the ground and engage safety stop on the feeder house cylinder 3.

  • Page 5: Bolt Torque

    TABLE OF CONTENTS FOREWARD..…………………………………………………………….…..2 WARRANTY…..…...……………………………………………………….….2 SAFETY INFORMATION…………………………………..…….....3 – 4 TABLE OF CONTENTS……………………………………………………..5 TORQUE / TOOLS REQUIRED.……………………………………...…..5 ASSEMBLY INSTRUCTIONS …..…...…………………………..6 – 11 5000-023 & 5000-024 …..…...………...………..……....6 – 8 5000-035…..…...……………..………..…....…....9 – 11 OPERATION / BEARING / STORAGE / LOCK UP...…..……………..12 PARTS IDENTIFICATON..............13 – 21 5000-023……………………………….…………….....…13 –...
  • Page 6 STEP 2. Install the Mount Assembly to the Corn Head Frame using 5/8” X 8” Bolts, Clamp Plates, 5/8” Washers, & 5/8” Lock Hex Nuts. NOTE: Do not fully tighten hardware until the pivot arms are installed during Step 6. 5000-023 & 5000-023A 6 ROW MOUNTING LOCATIONS 5000-024 & 5000-024A 8 ROW MOUNTING LOCATIONS...
  • Page 7 5000-023A & 5000-024A ASSEMBLY INSTRUCTION STEP 3: Attach the 5000-135 Arm Mounts to the Extension Mount Bracket using ½” X 2” Bolts, ½” Washers, & ½” Lock Hex Nuts. STEP 4: Install the 5000-323 Lock Up Pin in the storage location on the mount arms, secure with Hair Pin Clips.
  • Page 8 5000-023A & 5000-024A ASSEMBLY INSTRUCTION STEP 6: Install the push rods into the mount brackets & attach to the pivot arms using the 5/8” Shoulder Bolts 5/8” Washers, & ½” Jam Nuts. The washers are to be installed on each side of the “Eye” on the push Rod.
  • Page 9 5000-035A ASSEMBLY INSTRUCTION AGCO GLEANER 3308 STEP 1: Install the Mount Assemblies on the Corn Head Frame using 5/8” X 5 ½” Bolts, Mount Straps, Clamp Brackets/Straps, 5/8” Washers, & 5/8” Lock Hex Nut. Place Mounts, Mount Straps, & Brackets as shown. The Double Mount goes between rows 4 &...
  • Page 10 5000-035A ASSEMBLY INSTRUCTION STEP 3: Attach 1) 5000-135 Arm Mount on each Offset Mount using ½” X 1 ¾” Bolts, ½” Washers, & ½” Lock Hex Nuts. Attach 2 Arm Mounts to the Double Offset on rows 4 & 5. STEP 4: Install a 5000-323 Lock Up Pin in the storage location on the Mount Arms &...
  • Page 11 5000-035A ASSEMBLY INSTRUCTION STEP 6: Install the Push Rods into the Mount Brackets & attach to the Pivot Arms using 5/8” Shoulder Bolts, 5/8” Washers, & ½” Jam Lock Hex Nuts. The Washers are to be installed on each side of the “EYE” on the Push Rod.

  • Page 12: Operation

    OPERATION CORN HEAD ANGLE SHOULD BE BETWEEN 23 – 25° FOR OPTIMUM DEVASTATATOR PERFORMANCE. USE THE 5000-455 TO CHECK CORN HEAD ANGLE: Put the combine on a level surface. Lower the Corn head to your normal working head height. Place the magnetic protractor on the stripper plate to get the angle.
  • Page 13 PARTS IDENTIFICATION...
  • Page 14 PARTS IDENTIFICATION...
  • Page 15 PARTS IDENTIFICATION...
  • Page 16 PARTS IDENTIFICATION...
  • Page 17 PARTS IDENTIFICATION...
  • Page 18 PARTS IDENTIFICATION...
  • Page 19 PARTS IDENTIFICATION...
  • Page 20 PARTS IDENTIFICATION...
  • Page 21 PARTS IDENTIFICATION...

  • Page 22: Troublshooting

    TROUBLSHOOTING ISSUE CAUSE CORRECTIVE ACTION Residue Plugging 1. Incorrect Head Angle 1. Adjust head angle to 23 – 25 degrees (see page 12) 2. Roller Mount Tube 2. Make sure the Bearing Support Tab is on the backside incorrectly installed of the Roller Arm Mount Tube 3.
  • Page 24 NOTES 2565-784_REV_B • 12/18...

This manual is also suitable for:

5000 series5000-024a5000-035