Onkyo TX-NR3010 Instruction Manual page 68

Note
*1
"Full Band" can be selected only when "Full Band" is
selected in the "Front" setting.
*2 When the "Powered Zone 3" setting is set to "Yes", this
setting cannot be selected.
*3 This setting cannot be selected if the "Speakers
Type(Front A)" or "Speakers Type(Front B)" setting is set
to "Bi-Amp" or "Digital Crossover".
*4 When the "Powered Zone 2" setting is set to "Yes", this
setting cannot be selected.
*5
When the "Powered Zone 3" setting is set to "Yes"
(➔ page 66) while Powered Zone 2 is enabled
this setting cannot be selected.
*6 If the "Surround" setting is set to "None", this setting cannot
be selected.
*7 If the "11ch Playback" setting is enabled, "None" cannot be
selected.
*8 "Full Band" can be selected only when "Full Band" is
selected in the "Front"(Speakers A) setting.
*9
If anything other than "No" is selected in "Speakers
Type(Front B)", this setting cannot be selected.
*10 When the "Speakers Type(Front A)" setting is set to
"Bi-Amp" or "Digital Crossover" while Powered Zone 2 is
enabled (➔ page 89), this setting cannot be selected.
■
Surround Back Ch
1ch:
Select if only one surround back speaker L is
connected.
2ch:
Select if two (left and right) surround back speakers
are connected.
Note
• If the "Surround Back" setting is set to "None", this setting
cannot be selected.
■
LPF of LFE
(Low-Pass Filter for the LFE Channel)
80Hz, 90Hz, 100Hz, 110Hz, 120Hz
Off:
Low-Pass Filter is not applied.
With this setting, you can specify the cutoff frequency of
the LFE channel's low-pass filter (LPF), which can be
used to filter out unwanted hum. The LPF only applies to
sources that use the LFE channel.
Note
(➔ page 89),
• If you're using THX-certified speakers, select "80Hz".
■
Subwoofer Phase
0º
180º:
Moves the subwoofer phase.
Note
• If the "Subwoofer" setting is set to "No", this setting cannot be
selected.
■
Double Bass
This setting is NOT set automatically by
Audyssey MultEQ ®
Speaker Setup function
On
Off(THX)
Turn this setting on to boost bass output by feeding bass
sounds from the front left, right, and center channels to
the subwoofer.
Note
• When the "Subwoofer" setting is set to "No" or the "Front"
setting to anything other than "Full Band", this setting is fixed to
"- - - - -".
• This setting is set to "On" automatically when the "Subwoofer"
setting is set to "1ch" or "2ch" and the "Front" setting is set to
"Full Band" for the first time.
• If you're using THX-certified speakers, select "Off(THX)".
XT32 Room Correction and
(➔ page 42).
En-68
Advanced Operations
■
Subwoofer, Front, Center, Surround,
Front High, Surround Back
(Setting Speakers A and Speakers B)
Not Use:
Select if you don't want to use each speaker with
Speakers A or Speakers B.
Use:
Select if you do want to use each speaker with
Speakers A or Speakers B.
If you're using Speakers B, you can choose whether or not
to use the subwoofer, center, surround, front high, and
surround back speakers with the Speakers A and Speakers
B configurations independently. You cannot choose
whether or not to use the front speakers.
Note
• These settings can only be displayed when the "Speakers
Type(Front B)" setting is set to other than "No"
• You cannot select speakers that you set to "No" or "None".
• "Front" is fixed to "Use".
(➔ page 66).