Onkyo TX-NR3010 Instruction Manual page 67

Note
• "Speakers Type(Front A)" and "Speakers Type(Front B)"
cannot be set to "Bi-Amp" or "Digital Crossover" at the same
time.
• Powered Zone 2 cannot be used if "Speakers Type(Front B)" is
enabled.
• Powered Zone 3 is not available in the following cases:
– The "Speakers Type(Front A)" setting is set to "Bi-Amp" or
"Digital Crossover".
– The "Speakers Type(Front B)" is enabled.
– The "Powered Zone 2" setting is set to "No".
• When the "Powered Zone 3" setting is set to "Yes"
(➔ page 66) while Powered Zone 2 is enabled
the surround back speakers cannot be used.
• When the "Powered Zone 2" setting is set to "Yes", the front
wide speakers cannot be used.
• When the "Powered Zone 3" setting is set to "Yes", the front
high speakers cannot be used.
• "11ch Playback" is not available in the following cases:
– The "Speakers Type(Front A)" setting is set to "Bi-Amp" or
"Digital Crossover".
– The "Speakers Type(Front B)" is enabled.
– The "Powered Zone 2" setting is set to "Yes".
– The "Zone 2 HDMI" setting is set to "Use".
• If the "11ch Playback" setting is set to "Yes", the audio of front
wide channel is output from FRONT WIDE PRE OUT only.
Speaker Configuration
This setting is set automatically by
Audyssey MultEQ
Speaker Setup function
you need to change the settings manually.
With these settings, you can specify which speakers are
connected and a crossover frequency for each speaker.
You can set the crossover frequencies, distances, and levels
of the front speakers A and front speakers B independently.
(➔ page 89),
The other speakers (i.e., subwoofer, center, surround,
surround back and front high) use the same crossover
frequencies, distances, and levels for Speakers A and
Speakers B. Specify "Full Band" for speakers that can
output low frequency bass sounds adequately, for example,
speakers with a good sized woofer. For smaller speakers,
specify a crossover frequency. Sounds below the crossover
frequency will be output by the subwoofer instead of the
speaker. Refer to your speaker's manuals to determine the
optimum crossover frequencies. If you set up your
speakers using Audyssey MultEQ XT32 Room Correction
and Speaker Setup, please make sure manually that any
THX speakers are set to "80Hz(THX)" crossover.
■
Subwoofer
1ch:
Audio signal is outputted from SW1 jack only.
2ch:
Audio signal is outputted from SW1 and SW2 jacks.
No
® XT32 Room Correction and
(➔ page 42). For Speakers B,
En-67
Advanced Operations
■
Front
(Setting Speakers A and Speakers B)
Full Band
40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX),
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
Note
• If the "Subwoofer" setting is set to "No", the "Front" setting is
fixed at "Full Band".
• If any of "Center", "Surround", or "Front High" is set to "Full
Band", the "Front" (Speakers B) setting is fixed to "Full Band".
■
Center , Surround
*8 *8
Full Band
40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX),
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
None
■
Front Wide , Front High
*3*4*6*7*8*9
Full Band
40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX),
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
None
■
Surround Back
*1*5*6*10
Full Band
40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX),
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
None
*1*2*3*6
To be continued