Display - Pioneer Elite SC-37 Operating Instructions Manual

02 Controls and displays
HDMI OUT – Switch the HDMI output terminal
(page 81).
SIGNAL SEL – Use to select an input signal (page 62).
MCACC – Press to switch between MCACC presets
(page 62).
SLEEP – Use to put the receiver in sleep mode and
select the amount of time before sleep (page 81).
CH LEVEL – Press repeatedly to select a channel,
then use / to adjust the level (page 116).
A.ATT – Attenuates (lowers) the level of an analog
input signal to prevent distortion (page 80).
DIMMER – Dims or brightens the display (page 81).
9 MULTI-ZONE select buttons
Switch to perform operations in ZONE 2 and ZONE 3
(page 80).
10 Remote control LED
Lights when a command is sent from the remote control.

Display

1
AUTO
PCM
HDMI
DIGITAL
ANALOG
AUTO SURROUND
STREAM DIRECT
2
PROLOGIC x Neo:6
THX ADV.SURROUND
STEREO STANDARD
SP AB
6
15
1 SIGNAL indicators
Light to indicate the currently selected input signal.
AUTO lights when the receiver is set to select the input
signal automatically (page 62).
2 Program format indicators
Light to indicate the channels to which digital signals are
being input.
L/R – Left front/Right front channel
C – Center channel
SL/SR – Left surround/Right surround channel
LFE – Low frequency effects channel (the (( )) indicators light
when an LFE signal is being input)
XL/XR – Two channels other than the ones above
XC – Either one channel other than the ones above, the mono
surround channel or matrix encode flag
3 Digital format indicators
Light when a signal encoded in the corresponding format
is detected.
2 DIGITAL – Lights with Dolby Digital decoding.
2 DIGITAL PLUS – Lights with Dolby Digital Plus
decoding.
2 TrueHD – Lights with Dolby TrueHD decoding.
16
En
2 3
2
DIGITAL PLUS
L C R
2
TrueHD WMA9Pro
SL SR
DTS HD ES 96/24
XL XC XR
CD TUNER
LFE
MSTR
CD-R PHONO
SLEEP
16 17 18
11 RECEIVER
Switches the remote to control the receiver (used to
select the white commands).
Switch to perform operations in the main zone.
Also use this button to set up surround sound.
12 MASTER VOLUME +/–
Use to set the listening volume.
13 MUTE
Mutes the sound or restores the sound if it has been
muted (adjusting the volume also restores the sound).
14
Press to turn on/off the illumination for the buttons. The
way the buttons light can be selected from four modes
(page 99).
4 5 6 7
DSD PCM FULL BAND
MULTI-ZONE PQLS ALC ATT
OVER MONO
S.RTRV SOUND UP MIX
TV
DVD VIDEO
iPod BD DVR HDMI
19
DTS – Lights with DTS decoding.
DTS HD – Lights with DTS-HD decoding.
96/24 – Lights with DTS 96/24 decoding.
WMA9 Pro – Lights to indicate that a WMA9 Pro
signal is being decoded.
DSD PCM – Light during DSD (Direct Stream Digital)
to PCM conversion with SACDs.
PCM – Lights during playback of PCM signals.
MSTR – Lights during playback of DTS-HD Master
Audio signals.
4 MULTI-ZONE
Lights when the MULTI-ZONE feature is active (page 79).
5 FULL BAND
SC-37 only: Lights when the Full Band Phase Control is
switched on (page 63).
6 Listening mode indicators
AUTO SURROUND – Lights when the Auto Surround
feature is switched on (page 59).
ALC – Lights when the ALC (Auto level control) mode
is selected (page 62).
8 9 10 11 12
TUNED
STEREO
dB
HMG USB XM
[ 2 ] [ 3 ] [ 4 ]
13 14
20