Adapter Port; Video - Pioneer Elite SC-37 Operating Instructions Manual

Additional information
Symptom
The PHASE CONTROL feature
doesn't seem to have an
audible effect.
SC-37 only: Full Band Phase
Control cannot be selected.
Noise or hum can be heard
even when there is no sound
being input.
Can't select some Input
functions by the INPUT
SELECTOR on the front panel
or the INPUT SELECT button on
the remote control.
There seems to be a time lag
between the speakers and the
output of the subwoofer.
The maximum volume
available (shown in the front
panel display) is lower than the
+12dB maximum.

ADAPTER PORT

Symptom
The Bluetooth wireless
technology device cannot be
connected or operated.
Sound from the Bluetooth
wireless technology device is
not emitted or the sound is
interrupted.

Video

Symptom
No image is output when an
input is selected.
Remedy
• If applicable, check that the lowpass filter switch on your subwoofer is off, or the lowpass cutoff is
set to the highest frequency setting. If there is a PHASE setting on your subwoofer, set it to 0º (or
depending on the subwoofer, the setting where you think it has the best overall effect on the sound).
• Make sure the speaker distance setting is correct for all speakers (see Speaker Distance on
page 116).
• Perform Full Auto MCACC measurements (see Automatically conducting optimum sound tuning
(Full Auto MCACC) on page 43). Full Band Phase Control automatically turns on once measurements
are completed.
• Check that personal computers or other digital components connected to the same power source
are not causing interference.
• Check the Input Skip settings in the Input Setup menu.
• Check the HDMI Input assignment in the Input Setup menu then try OFF.
• See Automatically conducting optimum sound tuning (Full Auto MCACC) on page 43 to set up your
system again using MCACC (this will automatically compensate for a delay in the subwoofer output).
• Check that the Volume Limit is set to OFF (see Volume Setup on page 119).
• The channel level setting may be over 0dB.
Remedy
• Check that no object that emits electromagnetic waves in the 2.4 GHz band (microwave
oven, wireless LAN device or Bluetooth wireless technology apparatus) is near the unit. If
such an object is near the unit, set the unit far from it. Or, stop using the object emitting the
electromagnetic waves.
• Check that the Bluetooth wireless technology device is not too far from the unit and that
obstructions are not set between the Bluetooth wireless technology device and the unit. Set
the Bluetooth wireless technology device and the unit so that the distance between them is
less than about 10 m and no obstructions exist between them.
• Check that the Bluetooth ADAPTER and the ADAPTER PORT of the unit are correctly connected.
• The Bluetooth wireless technology device may not be set to the communication mode
supporting the Bluetooth wireless technology. Check the setting of the Bluetooth wireless
technology device.
• Check that pairing is correct. The pairing setting was deleted from this unit or the Bluetooth
wireless technology device. Reset the pairing.
• Check that the profile is correct. Use a Bluetooth wireless technology device that supports
A2DP profile and AVRCP profile.
Remedy
• Check the video connections of the source component (see page 32).
• For HDMI, or when digital video conversion is set to OFF and a TV and another component are
connected with different cords (in Setting the Video options on page 78), you must connect your TV
to this receiver using the same type of video cable as you used to connect your video component.
• Make sure the input assignment is correct for components connected using component video or
HDMI cables (see The Input Setup menu on page 45).
• Check the video output settings of the source component.
• Check that the video input you selected on your TV is correct.
• Some components (such as video game units) have resolutions that may not be converted. If
adjusting this receiver's Resolution setting (in Setting the Video options on page 78) and/or the
resolution settings on your component or display doesn't work, try switching Digital Video
Conversion (in Setting the Video options on page 78) to OFF.
13
125
En