Using Other Functions; Setting The Audio Options - Pioneer Elite SC-37 Operating Instructions Manual

09

Using other functions

Chapter 9:
Using other functions
Important
• The procedure for setting the receiver operation
mode differs for the remote controls included with
the SC-37 and SC-35. For the SC-37's remote control,
set the remote control operation selector switch to
RECEIVER. For the SC-35's remote control, press the
RECEIVER
button. When "set the remote control to
the receiver operation mode" is indicated in these
instructions, use the respective procedure described
above.

Setting the Audio options

There are a number of additional sound settings you can
make using the AUDIO PARAMETER menu. The
defaults, if not stated, are listed in bold.
Important
• Note that if a setting doesn't appear in the AUDIO
PARAMETER menu, it is unavailable due to the
current source, settings and status of the receiver.
1 Set the remote control to the receiver operation
mode, then press AUDIO PARAMETER.
Use / to select the setting you want to adjust.
2
Depending on the current status/mode of the receiver,
certain options may not be able to be selected. Check the
table below for notes on this.
Use / to set as necessary.
3
See the table below for the options available for each
setting.
4 Press RETURN to confirm and exit the menu.
Setting What it does
Selects your favorite MCACC
MCACC
(MCACC preset memory when multiple
preset) preset memories are saved. When
an MCACC preset memory has
been renamed, the given name is
displayed.
Switches on/off the effects of EQ
EQ
(Acoustic Pro.
Calibration
EQ)
Switches on/off the effects of
S-WAVE
(Standing Standing Wave Control.
Wave)
76
En
Setting
DELAY
(Sound
Delay)
MIDNIGHT Allows you to hear effective
LOUDNESS Used to get good bass and treble
TONE
(Tone
Control)
a
BASS
a
TREBLE
S.RTRV
(Sound
Retriever)
DNR
(Digital
Noise
Reduction)
DIALOG E
(Dialog
Enhance
ment)
Option(s)
M1. MEMORY 1
to
M6. MEMORY 6
Hi-bit32
Default:
(SC-37 only)
M1. MEMORY 1
(Hi-bit32/
High-
Sampling)
ON
OFF
Hi-bit
ON
(SC-35 only)
OFF
(High Bit/
High
Sampling)
What it does
Some monitors have a slight
delay when showing video, so the
soundtrack will be slightly out of
sync with the picture. By adding a
bit of delay, you can adjust the
sound to match the presentation
of the video.
surround sound of movies at low
volumes.
from music sources at low
volumes.
Applies the treble and bass tone
controls to a source, or bypasses
them completely.
Adjusts the amount of bass.
Adjusts the amount of treble.
With the Sound Retriever
function, DSP processing is used
to compensate for the loss of
audio data upon compression,
improving the sound's sense of
density and modulation.
May improve the quality of sound
in a noisy source (for example,
video tape with lots of background
noise) when switched on.
Localizes dialog in the center
channel to make it stand out from
other background sounds in a TV
or movie soundtrack. By moving
from UP1 through UP2 and UP3
up to UP4, you can make the
sound source seem to relocate
upwards.
Creates a wider dynamic range with
digital sources like CDs, DVDs or
BDs. Smoother, more delicate
musical expression can be achieved
by requantizing 16 bit PCM or 20 bit
compressed audio signals or 24 bit
compressed/lossless audio signals
to 32 bit.
Creates a wider dynamic range with
digital sources like CDs or DVDs.
Smoother, more delicate musical
expression can be achieved by
requantizing 16 bit PCM or 20 bit
compressed audio signals to 24 bit.
Option(s)
0.0 to 10.0
(frames)
1 second = 30
frames (NTSC)
Default: 0.0
MIDNIGHT/
LOUDNESS
OFF
MIDNIGHT ON
LOUDNESS
ON
BYPASS
ON
–6 to +6 (dB)
Default: 0 (dB)
–6 to +6 (dB)
Default: 0 (dB)
b
OFF
ON
OFF
ON
OFF
FLAT
UP1/UP2/UP3/
c
UP4
OFF
ON
OFF
ON