Setting The Remote To Control Other Components; Selecting Preset Codes Directly; Programming Signals From Other Remote Controls - Pioneer Elite SC-37 Operating Instructions Manual

Controlling the rest of your system (In case of SC-35)
Setting the remote to control other
components
Most components can be assigned to one of the input
function buttons (such as DVD or CD) using the
component's manufacturer preset code stored in the
remote.
However, there are cases where only certain functions
may be controllable after assigning the proper preset
code, or the codes for the manufacturer in the remote
control will not work for the model that you are using.
If you can't find a preset code that matches the
component you want to control, you can still teach the
remote individual commands from another remote
control (see Programming signals from other remote
controls on page 97).
• For greater convenience, assign the TV connected to
the MONITOR OUT terminal to the TV CTRL button,
and assign your satellite/cable receiver or set-top box
connected to the TV input terminal to the TV input
button. If a single device is connected to both
terminals, that device should be assigned to both the
TV CTRL and TV input buttons.
• Devices may be assigned to the following input
function buttons.
RECEIVER MULTI
OPERATION
R.SETUP
BD DVD
TV CD
iPod USB TUNER
INPUT SELECT

Selecting preset codes directly

1 Press and hold R.SETUP, then press "1" for three
seconds.
The LED flashes continuously.
• To cancel the preset setup mode press R.SETUP.
2 Press the input function button for the component
you want to control.
When assigning preset codes to TV CONTROL, press TV
CTRL here.
The LED blinks once and flashes continuously.
3 Use the number buttons to enter the 4-digit preset
code.
See Preset code list (SC-35 only) on page 139.
Note
1 The remote can store about 120 preset codes from other components (this has been tested with codes of Pioneer format only).
SOURCE
DVR/BDR HDMI
NET RADIO ADAPTER
SIRIUS XM
RECEIVER
TV CTRL
If the LED lights for one second, the setting has been
successfully completed.
When the preset code is fully input, the LED flashes three
times to indicate that the setting has failed. If this
happens, enter the 4-digit preset code again.
4 Repeat steps 2 through 3 for the other components
you want to control.
To try out the remote control, switch the component on or
off (into standby) by pressing  SOURCE. If it doesn't
seem to work, select the next code from the list (if there
is one).
5 Press R.SETUP to exit the preset setup mode.
Programming signals from other
remote controls
If the preset code for your component is not available, or
the available preset codes do not operate correctly, you
can program signals from the remote control of another
component. This can also be used to program additional
operations (buttons not covered in the presets) after
1
assigning a preset code.
Certain buttons represent operations that cannot be
learned from other remote controls. The buttons
available are shown below:
RECEIVER MULTI SOURCE
OPERATION
R.SETUP
BD DVD DVR/BDR HDMI
TV CD NET RADIO ADAPTER
iPod USB TUNER SIRIUS XM
RECEIVER
INPUT SELECT TV CTRL
MASTER
INPUT VOLUME
TV CONTROL
CH VOL
MUTE
1 Press and hold R.SETUP, then press "2" for three
seconds.
The LED flashes continuously.
• To cancel the preset setup mode press R.SETUP.
2 Press the input function button for the component
you want to control.
The LED blinks once and flashes continuously.
AUDIO VIDEO
PARAMETER PARAMETER
LIST TUNE TOOLS
TOP MENU T.EDIT
BAND GUIDE
PRESET ENTER PRESET
CATEGORY RETURN
HOME
TUNE
MENU
iPod CTRL
AUTO / ALC / PGM MEMORY MENU
STANDARD ADV SURR
DIRECT STEREO
HDD DVD
THX PHASE CTRL STATUS
TV / DTV MPX PQLS
HDMI OUT AUDIO
1 2 3
SIGNAL SEL MCACC SLEEP INFO
4 5 6
DISP
CH LEVEL A.ATT DIMMER
7 8 9
CH
D.ACCESS CLASS
/ CLR 0 ENTER
10
97
En