Adapter Port Terminal; Video - Pioneer SC-81 Operating Instructions Manual

13
Symptom Remedy
Certain listening modes or When Operation Mode is set to Basic, the Pioneer-recommended settings are made and
HOME MENU items cannot be not all of the functions can be used. To use all of the functions without restrictions, set
selected. Operation Mode to Expert (see
Some functions cannot be selected, depending on the input signal and listening mode.
The volume level drops automati- The temperature within the unit has exceeded the allowable value. Try moving the unit for
cally. better ventilation (see
Volume seems different when input Set the Channel Level setting to ALL, then adjust the volume of the respective input
is switched. sources (see Input Volume Absorber
When HDZONE is ON, multi-channel When HDZONE is selected in Speaker System and also the same HDMI input is selected
audio sources are not output in the for both the main zone and HDZONE, 2-channel PCM audio sources are output from the
main zone. main zone as well. To output multi-channel audio sources, set HDZONE to OFF or change
the HDZONE input.

ADAPTER PORT terminal

Symptom Remedy
The Bluetooth wireless technology Check that no object that emits electromagnetic waves in the 2.4 GHz band (microwave
device cannot be connected or oper- oven, wireless LAN device or Bluetooth wireless technology apparatus) is near the unit. If
ated. Sound from the Bluetooth wire- such an object is near the unit, set the unit far from it. Or, stop using the object emitting
less technology device is not emitted the electromagnetic waves.
or the sound is interrupted.
Check that the Bluetooth wireless technology device is not too far from the unit and that
obstructions are not set between the Bluetooth wireless technology device and the unit.
Set the Bluetooth wireless technology device and the unit so that the distance between
them is less than about 10 m (33 ft.) and no obstructions exist between them.
Check that the Bluetooth ADAPTER and the ADAPTER PORT of the unit are correctly
connected.
The Bluetooth wireless technology device may not be set to the communication mode
supporting the Bluetooth wireless technology. Check the setting of the Bluetooth wireless
technology device.
Check that pairing is correct. The pairing setting was deleted from this unit or the Blue-
tooth wireless technology device. Reset the pairing.
Check that the profile is correct. Use a Bluetooth wireless technology device that sup-
ports A2DP profile and AVRCP profile.
ADT OVERLOAD is displayed on the There is a problem in the power supply for the Bluetooth adapter. After turning OFF the
display. power of the receiver, disconnect the Bluetooth adapter and insert the Bluetooth adapter
again, then turn ON the power of the receiver.
If ADT OVERLOAD is displayed even though the above operation is repeated several
times, there is a problem with the receiver or the Bluetooth adapter. Disconnect the
power cable and request repair.
Operation Mode Setup on page 45 ).
Installing the receiver on page 10 ).
on page 75 ).

Video

Symptom Remedy
No image is output when an input is Check the video connections of the source component.
selected.
For HDMI, or when V.CONV is set to OFF and a TV and another component are con-
nected with different cords (in
your TV to this receiver using the same type of video cable as you used to connect your
video component. For the component video input, however, signals are only output from
the HDMI output, so when using the component video input, set V.CONV to ON.
Make sure the input assignment is correct for components connected using component
video or HDMI cables (see
Check the video output settings of the source component.
Check that the video input you selected on your TV is correct.
Some components (such as video game units) have resolutions that may not be con-
verted. If adjusting this receiver's Resolution setting (in
page 73 ) and/or the resolution settings on your component or display doesn't work, try
switching V.CONV (in
When the HDMI OUT 1/2 setting of the output parameter function is set to OFF, set it to
ON.
When the network function or iPod/USB input is selected in HDZONE, video connected
with the video cable or component cable is not output from the HDMI terminal. To output
video, turn off HDZONE or set HDZONE to some other input
Noisy, intermittent, or distorted Sometimes a video deck may output a noisy video signal (during scanning, for example),
picture. or the video quality may just be poor (with some video game units, for example). The
picture quality may also depend on the settings, etc. of your display device. Switch off
the video converter and reconnect the source and display device using the same type of
connection (component or composite), then start playback again.
Video signals are not output from the When a monitor only compatible with resolutions of 480i is connected to the component
component terminal. terminal and another monitor is connected to the HDMI terminal, the video signals may
not be output to the monitor connected to the component terminal. If this happens, do
the following:
— Turn off the power of the monitor connected to the HDMI terminal.
— Change the VIDEO P. menu RES setting (see
— Video signals from the HDMI terminal cannot be output to the component terminals.
Input the video signals from the player or other source to the composite or component
terminals. When using the component terminal, assign it at Input Setup (see
Setup menu
The picture's movement is unnatu- When Resolution under VIDEO PARAMETER is set to 1080/24p or 4K/24p, the picture
ral. may not be displayed properly for some source materials. In this case, set the resolution
to something other than 1080/24p or 4K/24p
Video parameters cannot be used. For audio only input (TUNER, CD, and TV), the video parameter function cannot be used.
Use for video or input with a GUI display.
Cannot be used when the HDZONE is ON. Turn OFF the HDZONE.
105
Setting the Video options on page 73 ), you must connect
The Input Setup menu on page 44 ).
Setting the Video options
Setting the Video options on page 73 ) to OFF.
(page 76 ).
Setting the Video options
on page 44 ).
(page 73 ).
FAQ
on
on page 73 ).
The Input