Related Manuals for Palmgren 9683421
Summary of Contents for Palmgren 9683421
- Page 1 Operating Manual & Parts List 9683421 10˝ left tilt Table Saw Read carefully and follow all safety rules and operating instructions before first use of this product. 965041501-0723...
-
Page 2: Getting Started
Palmgren Operating Manual & Parts List 9683421 CONTENTS OF THE SHIPPING CONTAINER GETTING STARTED MAIN SAW CONTAINER A Table Saw (1) STRUCTURAL REQUIREMENTS B Switch (1) Make sure all supporting structures and load attaching devices are C Table Insert (1) strong enough to hold your intended loads. -
Page 3: Safety Rules
Palmgren Operating Manual & Parts List 9683421 UNPACKING (CONTINUED) SAFETY RULES EXTENSION TABLE BOXES N Two extension tables are packaged in individual boxes. For your own safety, read operating instructions One extension table with sliding table manual before operating tool. - Page 4 Palmgren Operating Manual & Parts List 9683421 SAFETY RULES (CONTINUED) • Remove loose items and unnecessary work pieces from the area before starting the machine. • Check damaged parts. Before further use of the machine, a guard Familiarize yourself with the following safety notices used in this...
-
Page 5: Extension Table Assembly
Palmgren Operating Manual & Parts List 9683421 ASSEMBLY (CONTINUED) 6. Carefully turn the table over and place in-between the front and rear rail. 5. Bolt the front rail to the right extension wing with one 1/4˝-20 × 7. Use two c-clamps to hold the table in place. -
Page 6: Motor Cover
Palmgren Operating Manual & Parts List 9683421 ASSEMBLY (CONTINUED) 3. Install motor cover (G) by aligning the pins (H) on the cover with brackets on the cabinet. Refer to Figure 8. 7. Use a punch before drilling a 5/16˝ hole. -
Page 7: Miter Gauge And Fence Storage Hooks
Palmgren Operating Manual & Parts List 9683421 ASSEMBLY (CONTINUED) BLADE INSTALLATION/REPLACEMENT Refer to Figure 12. MITER GAUGE AND FENCE STORAGE HOOKS Use care when working with or around sharp Refer to Figure 9. saw blade to prevent injury! Hardware: (1) Small Hook (F), (2) Large Hook (K), (6) 1/4˝ Flat Washer Tools: 27mm Wrench (J), (6) 1/4˝... -
Page 8: Riving Knife And Guard Installation
Palmgren Operating Manual & Parts List 9683421 ASSEMBLY (CONTINUED) 6. Replace the insert (J) back on the table. The saw blade and riving knife should protrude through the slot in the insert. RIVING KNIFE AND GUARD INSTALLATION You should feel a snap as each piece locks in position. Attempt to lift Refer to Figures 13 and 14 as a test to make sure that they are securely locked in place. -
Page 9: Operation
Palmgren Operating Manual & Parts List 9683421 INSTALLATION (CONTINUED) PARALLEL TO THE MITER SLOT 1. Place the fence next to the outside edge of the right miter slot The on and off switch is thermally protected. If the saw motor is and lock it. -
Page 10: Insert Adjustment
Palmgren Operating Manual & Parts List 9683421 OPERATION (CONTINUED) BLADE HEIGHT 1. Loosen the lock knob (A) on the front handwheel (B). CURSOR ADJUSTMENT 2. Turn the handwheel (B) clockwise to raise and counterclockwise 1. Disconnect the table saw from the power source. -
Page 11: Riving Knife Adjustment
Palmgren Operating Manual & Parts List 9683421 OPERATION (CONTINUED) RIVING KNIFE ADJUSTMENT LATERAL ALIGNMENT The saw blade and riving knife must be in line as close as possible with each other (lateral alignment) for the prevention of kickback. Upon initial blade guard and riving knife installation no further adjustment should be necessary. -
Page 12: Blade Alignment
Palmgren Operating Manual & Parts List 9683421 OPERATION (CONTINUED) ADJUSTING 45º AND 90º POSITIVE STOPS The stops have been adjusted at the factory. After a period of use, or, BLADE ALIGNMENT after moving the saw to another location, the stops may no longer Refer to Figures 29 and 30. -
Page 13: Maintenance
Palmgren Operating Manual & Parts List 9683421 OPERATION (CONTINUED) MAINTENANCE 8. If the blade is not 45 degrees, remove the raising and lowering handle. Loosen lock nut (A, Fig. 33) and turn adjusting stop screw Always disconnect power to the machine before (B, Fig. -
Page 14: Troubleshooting
Palmgren Operating Manual & Parts List 9683421 TROUBLESHOOTING SYMPTOM POSSIBLE CAUSE(S) CORRECTIVE ACTION Saw stops or will not start. 1. Overload tripped. 1. Allow motor to cool and reset by pushing off switch 2. Saw unplugged from wall or motor. -
Page 15: Wiring Diagram
Palmgren Operating Manual & Parts List 9683421 WIRING DIAGRAM Figure 35 – Electrical wiring schematic, 3 HP, 230 V, single phase. - Page 16 Palmgren Operating Manual & Parts List 9683421 Figure 36 – Replacement Parts Illustration for Table and Cabinet Assembly 16 16...
- Page 17 Palmgren Operating Manual & Parts List 9683421 REPLACEMENT PARTS LIST FOR TABLE AND CABINET ASSEMBLY Ref. Ref. Description Part No. Qty. Description Part No. Qty. Lock Knob 965027601 Logo Label 965029101 Flat Washer 3/16˝ Motor Cord 965029201 Miter Gauge Body 965027701 Carriage Blot 3/4˝...
- Page 18 Palmgren Operating Manual & Parts List 9683421 Figure 37 – Replacement Parts Illustration for Motor Trunnion Assembly...
- Page 19 Palmgren Operating Manual & Parts List 9683421 REPLACEMENT PARTS LIST FOR MOTOR TRUNNION ASSEMBLY Ref. Ref. Description Part No. Qty. Description Part No. Qty. Arbor Nut 965030801 Lock Handle 965034501 Arbor Flange 965030901 Fiber Washer 3/4˝ 965034601 Saw Blade 10˝(254mm) 965031001 Hex Socket Cap Screw 5/16˝...
- Page 20 Palmgren Operating Manual & Parts List 9683421 Figure 38 – Replacement Parts Illustration for Blade Guard Assembly...
- Page 21 Palmgren Operating Manual & Parts List 9683421 REPLACEMENT PARTS LIST FOR BLADE GUARD ASSEMBLY Ref. Description Part Number Qty. Riving Knife 965038101 Blade Guard Body 965038201 Bushing (L) 965038301 Bushing (R) 965038401 Flat Head Screw M3 × 10 Lock Pin...
- Page 22 Palmgren Operating Manual & Parts List 9683421 9(10) 5(10) 5(10) 10(2) 12(2) 9(10) 11(2) 13(2) 16(2) 20(4) 33(2) 27(4) 20(4) 17(2) 19(4) 32(2) 18(4) Figure 39 – Replacement Parts Illustration for Fence Assembly...
- Page 23 Palmgren Operating Manual & Parts List 9683421 REPLACEMENT PARTS LIST FOR FENCE ASSEMBLY Ref. Description Part Number Qty. Left Side Plate 965040001 Fence Body Assembly 965040101 Tube Cover 965040201 Right Side Plate 965040301 Hex Nut 1/4˝ 965040401 Carriage Bolt 1/4˝ × 3/4˝...
- Page 24 Palmgren Operating Manual & Parts List 9683421 Figure 40 – Replacement Parts Illustration for Rail Assembly...
- Page 25 Palmgren Operating Manual & Parts List 9683421 REPLACEMENT PARTS LIST FOR RAIL ASSEMBLY Ref. Description Part Number Qty. Front Rail 965041601 Flat Head Screw 1/4˝ × 1-1/4˝ Flat Washer 1/4˝ Lock Washer 1/4˝ Hex Nut 1/4˝ Hex Cap Screw 1/4˝ × 3/4˝...
- Page 26 Palmgren Operating Manual & Parts List 9683421 NOTES...
- Page 27 Palmgren Operating Manual & Parts List 9683421 NOTES...
- Page 28 9683421 PALMGREN WARRANTY C.H. Hanson / Palmgren warrants their products to be free of defects in material or workmanship. This warranty does not cover defects due directly or indirectly to misuse, abuse, normal wear and tear, failure to properly maintain the product, heated, ground or otherwise altered, or used for a purpose other than that for which is was intended.
Need help?
Do you have a question about the 9683421 and is the answer not in the manual?
Questions and answers