Subscribe to Our Youtube Channel
Related Manuals for Palmgren 9683408
Summary of Contents for Palmgren 9683408
- Page 1 & parts list 9683408 10” Table Saw Read carefully and follow all safety rules and operating instructions before first use of this product. 9683408.08-0922...
- Page 2 PALMGREN Operating Manual & Parts List 9683408 DESCRIPTION The PALMGREN 10” Table Saw, model number 9683408 offers precise cutting performance for wood up to 3-9⁄64” thick. The 10” table saw is recommended for use with a 10” blade. You can use this tool for the purposes listed below: •...
-
Page 3: Specifications
PALMGREN Operating Manual & Parts List 9683408 Screws ST4.2 x 9.5 (6) The term “power tool” in the warnings refers to your mains-operated Hex bolts M8 x 35 and flat washers 8 (4) (corded) power tool or battery-operated (cordless) power tool. - Page 4 PALMGREN Operating Manual & Parts List 9683408 and safer at the rate for which it was designed. loss of eyesight. • Do not use the power tool if the switch does not turn it on and • Read instruction manual and know your tool. Read and off.
- Page 5 PALMGREN Operating Manual & Parts List 9683408 operate tool. • Keep hands away from cutting area. Keep hands away from • Don’t overreach. Keep proper footing and balance at all times. blades. Do not reach underneath work or around or over the •...
- Page 6 PALMGREN Operating Manual & Parts List 9683408 taking breaks, cleaning up saw dust, or checking the tool's Freehand sawing leads to misalignment, binding and kickback. condition. • Never reach around or over a rotating saw blade. Reaching for a workpiece may lead to accidental contact with the moving saw Safety instructions for table saws blade.
- Page 7 PALMGREN Operating Manual & Parts List 9683408 stalling and kickback. ripping or cross cutting. Keep the blade guard down, the anti-kickback pawls down, and the riving knife in place. Make sure 4) Table saw operating procedure warnings the blade guard, riving knife, and anti-kickback pawls are •...
-
Page 8: Double Insulation
PALMGREN Operating Manual & Parts List 9683408 USE SAFETY GOGGLES AND EAR PROTECTION: GUIDELINES FOR EXTENSION CORDS ALWAYS WEAR EYE PROTECTION THAT CONFORMS WITH Use a proper extension cord. Make sure extension cords are in CUL REQUIREMENTS. FLYING DEBRIS can cause permanent good condition. - Page 9 PALMGREN Operating Manual & Parts List 9683408 Bevel scale and bevel indicator: 13 14 The easy-to-read scale and indicator on the front of the cabinet shows the exact blade angle. Saw blade: For maximum performance, it is recommended that you use the 40-tooth, 10"...
-
Page 10: Assemble The Stand
PALMGREN Operating Manual & Parts List 9683408 This table can be extended to provide extra support for long • Always hold the workpiece firmly with both hands or with push workpieces during ripping. sticks. Keep your body in a balanced position to be ready to resist kickback should it occur. - Page 11 PALMGREN Operating Manual & Parts List 9683408 • Turn the handwheel (2) clockwise to move along the arc rail causing the blade to bevel from 0 – 45°, or turn counter-clockwise to reduce the bevel angle. • Secure the blade bevel lock lever (3) when the bevel angle pointer points at desired angle on scale.
- Page 12 PALMGREN Operating Manual & Parts List 9683408 In uppermost position for through cuts In middle position for In down position for non-through cuts shipping Figure 5b Figure 6b To place riving knife in middle or down position, refer to the RIVING KNIFE INSTALLATION AND POSITION above procedure.
-
Page 13: Blade Guard Installation
PALMGREN Operating Manual & Parts List 9683408 WARNING! If the inner blade flange has been removed, reinstall it BLADE GUARD INSTALLATION before placing the saw blade on arbour. Failure to do so could Refer to Figure 9a-9b cause an accident. -
Page 14: Installation
PALMGREN Operating Manual & Parts List 9683408 RIP FENCE INSTALLATION AND USE CHECK THE ALIGNMENT OF THE RIP FENCE TO THE BLADE Refer to Figure 10a-10b Refer to Figure 11 • Unplug the saw. INSTALLATION: • Remove the blade guard assembly and anti-kickback pawls •... - Page 15 PALMGREN Operating Manual & Parts List 9683408 MITRE GAUGE INSTALLATION AND USE Refer to Figure 13a-13c INSTALLATION: The mitre gauge (1) can be installed on each mitre gauge groove (2) on either side of blade. • Slide the two screws (3) of locking knobs (4) to the slot of the parallel profile (5).
- Page 16 PALMGREN Operating Manual & Parts List 9683408 Figure 15 Figure 17a USE THE RIGHT EXTENSION TABLE Refer to Figure 16 • Loosen the locking knobs (1) under the work table. • Slide the extension table (2) in or out until the extension pole (3) is positioned at the desired distance.
- Page 17 PALMGREN Operating Manual & Parts List 9683408 CHANGE THE BLADE DEPTH ADJUST THE BEVEL STOPS Refer to Figure 19 Refer to Figure 21a-21c Blade depth should be set so that outer points of blade are higher This saw has positive stops that will quickly position the saw blade than workpiece by approximately 1/8"...
- Page 18 PALMGREN Operating Manual & Parts List 9683408 Figure 21c Figure 23a • Align the holes in the anti-kickback pawls storage (4) with ADJUST THE BEVEL INDICATOR corresponding holes on the right side of the saw. Refer to Figure 22 • Insert screws ST 4.2 x 9.5 (3) the into the aligned holes of the •...
- Page 19 PALMGREN Operating Manual & Parts List 9683408 STORE THE TABLE SAW ACCESSORIES Refer to Figure 25 The table saw has four convenient storage areas (one on each side and rear of the saw cabinet and right side of underneath the work table) specifically designed for the saw’s accessories: blade (1),...
-
Page 20: Operation
PALMGREN Operating Manual & Parts List 9683408 • Lock the left leg set (2) and right leg set (4) in unfolded position • Bevel locking lever is locked. by tightening the stand leg-locking knobs (1 and 3). • If ripping, ensure that rip fence locking handle is locked and that the fence is parallel to the blade. -
Page 21: Avoiding Kickback
PALMGREN Operating Manual & Parts List 9683408 by any action that pinches the blade in the wood, such as the • Never cut more than one workpiece, stacked vertically or following: horizontally. The saw blade could pick up one or more pieces and •... - Page 22 PALMGREN Operating Manual & Parts List 9683408 HOW TO MAKE AN ADDITIONAL PUSH STICK Refer to Figure 29 • In order to operate your table saw safely, you must use a push Wooden stick whenever the size or shape of the workpiece would dowel otherwise cause your hands to be within 6"...
-
Page 23: Auxiliary Fence
PALMGREN Operating Manual & Parts List 9683408 WARNING! When using a featherboard, it must be mounted in WARNING! Use extra caution when cutting wood products having front of the blade and used only against the uncut portion of the slippery surface as the anti-kickback pawls may not always be workpiece to avoid a kickback that could result in serious injury. - Page 24 PALMGREN Operating Manual & Parts List 9683408 wood first. CAUTION! The hand closest to the blade should be placed on the mitre gauge lock knob and the hand farthest from the blade TYPES OF CUTS should be placed on the workpiece.
-
Page 25: Making A Bevel Rip Cut
PALMGREN Operating Manual & Parts List 9683408 • Lock bevel locking lever. to a complete stop before removing the workpiece. • Set blade to correct depth for workpiece. MAKING A NON-THROUGH CUT • Set mitre gauge to 0° and tighten lock knob. -
Page 26: General Maintenance
PALMGREN Operating Manual & Parts List 9683408 location when reinstalling standard blade. Failure to do so can GENERAL MAINTENANCE result in possible injury and damage to the tool. Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents WARNING! Always use push blocks, push sticks, and/or and may be damaged by their use. - Page 27 PALMGREN Operating Manual & Parts List 9683408 SYMPTOM POSSIBLE CAUSE(S) CORRECTIVE ACTION SYMPTOM POSSIBLE CAUSE(S) CORRECTIVE ACTION Saw makes • Dull blade. • Replace blade. Blade does not • Sawdust and dirt in • Brush or blow out unsatisfactory • Blade mounted •...
- Page 28 PALMGREN Operating Manual & Parts List 9683408...
- Page 29 PALMGREN Operating Manual & Parts List 9683408...
- Page 30 PALMGREN Operating Manual & Parts List 9683408...
- Page 31 PALMGREN Operating Manual & Parts List 9683408...
- Page 32 PALMGREN Operating Manual & Parts List 9683408 196 195...
-
Page 33: Replacement Parts List
PALMGREN Operating Manual & Parts List 9683408 REPLACEMENT PARTS LIST Ref. Part Ref. Part Number Description Qty. Number Description Qty. 964963301 Roller wheel 964966601 Switch panel Screw M6 x 16 964966701 Main label Spring washer M6 Screw M5 x 10... - Page 34 PALMGREN Operating Manual & Parts List 9683408 Ref. Part Ref. Part Number Description Qty. Number Description Qty. 964971301 Lock plate 964977701 Washer 964971401 Special screw 964977801 Right blade guard 964971501 Eccentric handle 964977901 Anti-kickback pawl (A) Cam press plate Pin spring...
- Page 35 PALMGREN Operating Manual & Parts List 9683408 NOTES...
- Page 36 PALMGREN Operating Manual & Parts List 9683408 NOTES...
- Page 37 PALMGREN Operating Manual & Parts List 9683408 NOTES...
- Page 38 PALMGREN Operating Manual & Parts List 9683408 NOTES...
-
Page 39: Service Record
PALMGREN Operating Manual & Parts List 9683408 SERVICE RECORD Date Description... -
Page 40: Warranty
- 3 YEARS. The obligation of C.H. Hanson / Palmgren is limited solely to the repair or replacement, at our option, at its factory or authorized repair agent of any part that should prove inoperable.
Need help?
Do you have a question about the 9683408 and is the answer not in the manual?
Questions and answers