Roban AH-1 Instruction Manual

Roban AH-1 Instruction Manual

Scale fuselage 500 size

Advertisement

Instruction manual
Scale Fuselage AH-1
500 size
1.
INTRODUCTION
Thank you for buying Roban Model products. The 500 size EC-135 scale fuselage is designed as an easy
to use product. Please read the manual carefully before assembling the model, and follow all
precautions and recommendations located within the manual. Be sure to retain the manual for future
reference, routine maintenance and tuning. The scale fuselage is designed for T-REX 500 Helicopter
series use. You can easily put it on your T-REX 500 for new clothing.
Important Note
Roban Model R/C Helicopters are advanced, high-performance devices, built incorporating the latest
technologies. They are not intended as toys, and improper use can potentially lead to serious injury, or
even fatal accidents. We implore you to read this manual thoroughly before operating these models.
Safety should be your utmost priority - not just your own, but also that of others and your surroundings
when piloting Roban Model products.
Liability Disclaimer:
The manufacturer and the seller cannot accept liability for the operation or misuse of this product.
Roban Model R/C helicopters are intended to be used exclusively by experienced adults in legally
sanctioned flying fields. Once sold, we cannot monitor or control the product's operation or usage.
Operation Guidelines:
Upon assembly of the scale fuselage, the weight and complexity of the structure will increase. To
mitigate risk of accidents and damages, we advise against attempting 3D flights.
Skill Requirements:

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AH-1 and is the answer not in the manual?

Questions and answers

Summary of Contents for Roban AH-1

  • Page 1 500 size INTRODUCTION Thank you for buying Roban Model products. The 500 size EC-135 scale fuselage is designed as an easy to use product. Please read the manual carefully before assembling the model, and follow all precautions and recommendations located within the manual. Be sure to retain the manual for future reference, routine maintenance and tuning.
  • Page 2 The operation of R/C products necessitates a certain level of skill and familiarity. Any damages or dissatisfaction resulting from accidents, modifications, or operational mishaps are not covered under any warranty. Consequently, such products cannot be returned for repair or if you experience problems during operation or maintenance.
  • Page 3: Contents Of Kit

    CONTENTS OF KIT Please check the contents of the kit prior to installation. SCOPE OF DELIVERY Item No. Description Quantity Landing gear skids Landing gear struts T-connectors LED System LED Covers Main frame Tail tube holder Screw M2.5x20 Nut M2 Screw M2x12 Mounting blocks Washer M2...
  • Page 4 Linkage Tail shaft Tail skid Redirection shaft Fins Boom Rocket launcher Rocket launcher Decal Screw M3x14 REQUIRED TOOLS / CONSUMABLES Tool No. Tool/Consumable Hobby knife Allen wrench Phillips screwdriver File Side cutters Silicone adhesive Super glue 2K Epoxy glue Fine sandpaper Scissors...
  • Page 5: Installation

    INSTALLATION 4.1. Assemble the landing gear struts by inserting them. 4.2. Secure them with 4 screws, size A3x14 from the inside. 4.3. Install the T-connectors as shown, do not glue them in yet.
  • Page 6 4.4. Mount the skids and glue them as shown, as well as the side to the struts. Align them properly. 4.5. Install the LED lighting set. 4.6. Glue the lamp covers as shown.
  • Page 7 4.7. Install the provided main frame and the rear tail elevation set. 4.8. Mount the pushrod for the tail with the guide rings as shown. 4.9. Install the rear gearbox as shown. Fly the mechanics with the 3D landing gear and check everything without the fuselage.
  • Page 8 4.11. Remove the tail gearbox as shown. 4.12. Remove the tail cover. 4.13. Insert the mechanics into the fuselage.
  • Page 9 4.14. The mechanis tail mounting blocks must engage into these slots! 4.15. Install the tail rotor as shown. 4.16. Install the linkage on the gearbox.
  • Page 10 4.17. Secure the mechanics with 2 pieces of Screw M2x12 and washer. 4.18. Install the tail cover again and the tail skid with glue. 4.19. Glue the the rockets to the winglet as shown on both sides.
  • Page 11 4.20. Glue the winglet into the fuselage as shown. 4.21. Glue the fins as shown. 4.22. Glue the fins as shown.
  • Page 12: Spare Parts List

    5. SPAREPARTS LIST 500 AH-1 500AH1 前头 AC500PJ001 canopy 500 AH-1 500AH1 前窗 AC500PJ002 window set 500AH1 机翼 500 AH-1 AC500PJ003 组 stub wings 500 AH-1 500AH1 武器 AC500PJ004 weapon set 500AH1 像真 500 AH-1 AC500PJ005 件 antenna set 500 AH-1 500AH1 脚架...
  • Page 13 500 AH-1 500AH1 水印 AC500PJ011 decals 500 AH-1 500 轴传通用 500WBX tail 尾波箱 gearbox 500 轴传通用 500 AH-1 500WBX01 短尾管+轴+ short tail 拉杆 tubes 500 轴传通用 500 AH-1 500WBX02 扇齿 tail gears 500 轴传 45 500 AH-1 tail 500WBX03 度斜齿 gear...
  • Page 14 6. ILLUSTRATION OF READY MOUNTED HELICOPTER Specifications: Length: 1125mm Height: 244mm Width: 330mm Weight: 700g Suitable for Align TREX500 und similar mechanics We wish you a lot of fun with the fuselage! Copyright 2024 – www.robanmodel.com...

This manual is also suitable for:

Ec-135Ah-1sHsb-ac500wHsb-ac500grHsb-ac500mi

Table of Contents