1. Manuals
  2. Brands
  3. DAQ system Manuals
  4. Computer Hardware
  5. cPCI-SBC01
  6. User manual

DAQ system cPCI-SBC01 User Manual

Hide thumbs Also See for cPCI-SBC01:
Table of Contents

Advertisement

Quick Links

Download this manual
cPCI-SBC01
User Manual
Version 1.0
ⓒ 2005 DAQ SYSTEM Co., Ltd. All rights reserved.
Microsoft® is a registered trademark; Windows®, Windows NT®, Windows XP®, Windows 7®, Windows 8®, Windows 10®
All other trademarks or intellectual property mentioned herein belongs to their respective owners.
Information furnished by DAQ SYSTEM is believed to be accurate and reliable, However, no responsibility is assumed by DAQ SYSTEM for its use, nor
for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under
any patent or copyrights of DAQ SYSTEM.
The information in this document is subject to change without notice and no part of this document may be copied or reproduced without the prior
written consent.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the cPCI-SBC01 and is the answer not in the manual?

Questions and answers

Related Manuals for DAQ system cPCI-SBC01

Summary of Contents for DAQ system cPCI-SBC01

  • Page 1 All other trademarks or intellectual property mentioned herein belongs to their respective owners. Information furnished by DAQ SYSTEM is believed to be accurate and reliable, However, no responsibility is assumed by DAQ SYSTEM for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or copyrights of DAQ SYSTEM.

  • Page 2: Table Of Contents

    User‟s Manual Contents 1. cPCI-SBC01 Introduction ------------------------------------------------------------ 2. cPCI-SBC01 Appearance ------------------------------------------------------------- 3. cPCI-SBC01 Assembly (Memory, Hard Disk) ------------------------------ 4. Peripheral Device Control through Compact PCI Interface (Back-Plane Connection) ------------------------------------------------------------- 5. Expansion Port through Transition Board ---------------------------------- 6. Windows Installation ---------------------------------------------------------------- 7.

  • Page 3: Cpci-Sbc01 Introduction

    User‟s Manual 1. cPCI-SBC01 Introduction Introduction Low-cost Single Board Computer (SBC) equipped with low-power, low-heat  processor Provides a solution suitable for the embedded market that wants low power and  small size Features Low cost, Low power and fan-less Single Board Computer ...
  • Page 4 User‟s Manual Application Factory Automation  Data acquisition  Medical and Robotics  Auto PC  UMPC(Ultra Mobile PC)  Instrument control PC ...

  • Page 5: Cpci-Sbc01 Appearance

    VGA, SW, Network, USB - The front of cPCI-SBC01 has a connector out (VGA, power SWITCH, Ethernet, 2xUSB, power LED, Audio-Jack) that can be used in a general PC. If +5V power is applied, it can be used as a portable - It is a compact PCI interface from the rear, and it is possible to control other devices by connecting to the Back-Plane.

  • Page 6: Cpci-Sbc01 Assembly (Memory, Hard Disk)

    User‟s Manual 3. cPCI-SBC01 Assembly (Memory, Hard Disk) 1. Memory (SODIMM – SDRAM) Connection Memory connection with J4 connector (256M ~ 1G) Combination of Hard Disk connection board The figure below is the CF card connection board. (A board change is required when connecting a 1.8” hard disk.)
  • Page 7 User‟s Manual Hard disk connection (The figure is a CF card connection figure) Note) When 1.8” IDE HDD is applied, the connection board is different and may look different from the picture above.

  • Page 8: Peripheral Device Control Through Compact Pci Interface (Back-Plane Connection)

    User‟s Manual 4. Peripheral Device Control through Compact PCI interface (Back-Plane Connection) cPCI-SBC01 Switch Usage – Our Product cPCI-EK01 Audio Ethernet 2xUSB As shown in the picture above, you can control and use Compact PCI products by connecting to the...

  • Page 9: Expansion Port Through Transition Board

    User‟s Manual 5. Expansion Port through Transition Board 2xUSB Expansion rear RS232 interface serial 2xPS2 Through Back-Plane, by connecting with cPCI-SBC01, Port extension can be used. (sold separately)

  • Page 10: Windows Installation

    User‟s Manual 6. WINDOWS Installation 1. Connect KEYBOARD, MOUSE, and USB CD-ROM (WINDOSW CD) to the board using a USB hub. After connecting the monitor to the DSUB 15 PIN VGA PORT, connect the power (5V, 3A) and turn on the S/W.
  • Page 11 User‟s Manual 4. Select “USB CD-ROM Drive <- Conflict 4” in “1” and press Esc to exit. 5. Select “Save values and Exit” (shortcut “X”) and exit. 6. Booting from the USB CD-ROM is made, and you can proceed according to the Windows installation order.

  • Page 12: Driver Installation

    User‟s Manual 7. Driver Installation - There is a driver in the CD ROM enclosed with the product. AUDIO Driver Installation MyComputer => Property => Hardware => Device Manager Choose “Audio device”. Click the right mouse, select the “driver update”.

  • Page 13: Touch Driver Installation (Installation When Using 7" Lcd)

    User‟s Manual 7-5 Touch Driver Installation (Installation when using 7” LCD) - After executing the Setup file in the Touch folder on the CD-ROM and installing it, the execution screen appears on the desktop. If you double-click the execution screen, the following screen appears.
  • Page 14 User‟s Manual - After finding the port to which the Touch Controller is connected, press the OK button. - Select “Calibrate” and press the „Calibrate‟ button on the screen below. When the screen below appears, press and hold the blinking point.

  • Page 15: Optimal Display Settings For Lcd

    User‟s Manual - If you press all the way down in the correct order, the above screen appears. Press “Yes” to exit and it is done. 7-6 Optimal Display Settings for LCD Since 800 X 480 is optimal for LCD resolution, you need to change the resolution to 800 X 480.
  • Page 16 User‟s Manual When the display properties screen appears, click the Advanced button in Settings. After clicking the “Show All Modes” button in the adapter section, select 800 x 480 true color, click OK, and then click Apply. If the red circle is displayed in the display properties, the setting has been applied.

  • Page 17: Appendix

    (3) All DAQSYSTEM products have a one-year warranty. -. The warranty period is counted from the date the product is shipped from DAQ SYSTEM. -. Peripherals and third-party products not manufactured by DAQ SYSTEM are covered by the manufacturer's warranty.
  • Page 18 User‟s Manual MEMO Contact Point Web sit : https://www.daqsystem.com Email : postmaster@daqsystem.com...

Table of Contents