Subscribe to Our Youtube Channel
Related Manuals for Durr Dental Hygopac Plus
Summary of Contents for Durr Dental Hygopac Plus
- Page 1 Hygopac Plus Installation and Operating Instructions 9000-616-37/02 ...
-
Page 3: Table Of Contents
Contents 8 Commissioning and first start-up 13 Monitoring the device with Tyscor Pulse 13 Important information Handover of the device 14 1 About this document 2 9 Settings upon commissioning 14 Warnings and symbols 2... -
Page 4: Important Information
Important information About this document Other symbols These symbols are used in the document and These installation and operating instructions on or in the unit: form part of the unit Note, eg specific instructions regarding If the instructions and information in efficient and cost-effective use of the unit these installation and operating instruc- tions are not followed, Dürr Dental will Comply with the Operating Instructions... -
Page 5: 12 Copyright Information
Important information Safety 1.2 Copyright information All names of circuits, processes, names, soft- Dürr Dental has designed and constructed this ware programs and units used in this document device so that when used properly and for the are protected by copyright intended purpose there is no danger to people The Installation and Operating Instructions must or property Nevertheless, residual risks can re-... -
Page 6: Qualified Personnel
Important information 2.4 Qualified personnel 2.7 Transport The original packaging provides optimum pro- Operation tection for the device during transport Persons who operate the units must ensure safe If required, original packaging for the unit can be and correct handling based on their training and ordered from Dürr Dental knowledge Instruct or have every user instructed in han-... -
Page 7: Product Description
150 cm x 100 m 6020-053-50 delivery: 250 cm x 100 m 6020-055-50 Hygopac Plus .... 6022-80 – Hygopac Plus 3.5 Wear parts and spare parts – Mains cable – SD memory card... -
Page 8: Technical Data
Product description Technical data Electrical data Voltage 230, 1~ Frequency 50 - 60 Nominal current Power output, max Fuses IEC 127-2/V-T 50 AH Type of protection IP 20 Protection class General data Max sealing temperature (adjustable in 5°C steps) °C Heating performance 2 x 400 Warm-up time approx Rate of sealing m/min... -
Page 9: Type Plate
Product description 4.1 Type plate The type plate is located on the rear side of the unit Type plate 9000-616-37/02 1801V003... -
Page 10: Declaration Of Conformity
Höpfigheimer Str 17 74321 Bietigheim-Bissingen Germany Name of product: Hygopac Plus We hereby declare that the above product meets all applicable requirements of the directives listed below: – Machinery directive 2006/42/EC in its current version Name of the person with responsibility for compiling all technical documentation:... -
Page 11: Operation
Product description Operation On / off switch Standby LED Button – "Cancel" or "No" Shift key – switching between display / menu Display Button – "Confirm" or "Yes" Arrow keys for navigation Infeed Adjustable stop 10 SD card slot 11 Outlet 12 Mains connection 13 Fuse holder 14 Network connection... -
Page 12: Display Overview
Product description In the area of the infeed there is a light barrier that is used to detect inserted sterilisation packaging and start the transport Then the transport belt runs for a maximum foil width of 50 cm If a new foil is quickly inserted afterwards but not placed against the adjustable stop, a foil can be picked up by the transport belt without the light barrier being triggered The infeed is designed so that only the thin sterilisation packaging can be fed into the unit This ensures that no sterilisation materials can be... -
Page 13: Tyscor Pulse (Optional)
Product description 5.2 Tyscor Pulse (optional) The software is connected via the network to the devices from Dürr Dental and displays the current status as well as messages and errors All messages are logged and can be printed or sent The cockpit shows the devices with the current characteristic data and provides a quick overview of the functional status of the devices The software interface consists of the menu bar, the side bar and the contents area Menu bar... -
Page 14: Installation
Installation Requirements Installation 6.1 Installation/setup room The room chosen for set up must fulfil the following requirements: – Closed, dry, well-ventilated room – Should not be a room made for another pur- pose (e g boiler room or wet cell) Ambient and environmental conditions must be taken into account Do not oper- ate the unit in damp or wet conditions 6.2 Setup options... -
Page 15: Commissioning And First Start-Up
Installation Commissioning and first The list of units appears A symbol displays the connection status to the software: start-up The device is present in the network Insert the SD card into the unit and connected to the software Switch the unit on via the on / off switch The device is present in the network Perform a basic set-up for the unit –... -
Page 16: Handover Of The Device
Installation Settings upon commis- 8.2 Handover of the device sioning A performance test is carried out on the device at the factory, and a printout of these test results is included in the sup- plied documents This test only relates to Dürr Dental Hygofol transparent sterile product packaging If other sterile prod- uct packaging (from other manufacturers) is to be sealed with the device, this must... -
Page 17: Adjusting The Temperature
Installation 9.3 Adjusting the temperature Use the button to switch back to the dis- play window or use to switch back to the Press the button to switch from the dis- next higher menu level play screen to the menu screen Use the button to scroll to the menu item Syslog settings Settings and press... -
Page 18: Use Of Suitable Sterile Product
Operation 10 Use of suitable sterile – Allow at least 2 cm foil distance to protrude to the back behind the sealing seam This product packaging ensures unhindered peeling of the seam and is used for applying the labels or stickers Can The following may be used: be set with adjustable stop Sterile product packaging in accordance with –... -
Page 19: Operation
The following is shown in the unit block of the Place the sterilisation packaging up Hygopac Plus: against the stop (this is the only way – Sequential number of the last sealing process to ensure that the light barrier will be –... -
Page 20: 122 Completing The Task
Operation 13 Adjustment of the If a message occurs for an device, the symbol next to the device in the side bar changes The adjustable stop message appears in the cockpit and in the de- vice details With the aid of the adjustable stop, the distance If several messages occur, the symbol of the between the sealing seam and the edge can be highest message level in each case is displayed... -
Page 21: Validation Of The Sealing Process
Operation 14 Validation of the sealing Adjust the temperature as described in "93 Adjusting the temperature" and perform the process operational qualification again 14.1 Validation steps 14.3 Annual Performance The validation of the sealing process consists of Qualification the following steps: If the menu item Performance qualification is –... -
Page 22: Disinfection And Cleaning
Operation 15 Disinfection and cleaning Switch off and de-energise the unit (eg unplug from mains) Only damp-wipe the unit when it is cold Disinfect and clean the external surfaces using disinfectant and cleaning wipes that are com- patible with the material and have been specifi- cally approved by Dürr Dental, eg FD 350 dis- infection wipes 9000-616-37/02 1801V003... -
Page 23: Troubleshooting
Troubleshooting 16 Tips for operators and service technicians Any repairs above and beyond routine maintenance must only be carried out by suitably quali- fied personnel or by one of our service technicians Prior to working on the device or in case of danger, disconnect it from the mains (e g pull the mains plug) Error messages with a Note must be acknowledged by pressing to get the unit ready for... - Page 24 Troubleshooting Fault Probable cause Solution Note: Inadequate ventilation of the unit Acknowledge the message Provide sufficient ventilation Unit overheating! Please Defective heating system Wait until the temperature has wait settled within the required range If necessary, check the current temperature in the menu under Sealing parameters In the event of a persistent fault, con- tact a Service Technician...
- Page 25 Troubleshooting Fault Probable cause Solution Note NTP server IP under Settings -> Acknowledge the message Date & Time -> [x] Automatic -> Check the NTP server settings No NTP server found. NTP server incorrect or no net- If necessary, contact the net- work or NTP server available work administrator Check the network cable Note...
-
Page 26: Appendix
Appendix 17 Menu structure Language [X] Deutsch [ ] English [ ] Français (other languag- Device information REF: Firmware: Sealing Temperature: parameters xxx °C Pressing force: xx N Speed: xx mm/s Settings Setpoint tempera- xxx °C ture Validation Operational qualifi- [X] Activated cation [ ] Deactivated... -
Page 27: Sealing Log
Pass 2014-11-05 14:31:58 +00:00 444 Pass 2014-11-05 14:32:07 +00:00 445 Pass Explanation: Hygopac Plus; item designation 6022-80; order number EX00112; serial number 1423677; firmware version Time; comprising the date, time and **time zone** LOT; sequential batch number Temperature; temperature during the sealing process Pressing force;... - Page 28 Hersteller/Manufacturer: DÜRR DENTAL SE Höpfigheimer Str. 17 74321 Bietigheim-Bissingen Germany Fon: +49 7142 705-0 www.duerrdental.com info@duerrdental.com...
Need help?
Do you have a question about the Hygopac Plus and is the answer not in the manual?
Questions and answers