Omron EJ1 User Manual page 274

Parameter List
Variable CompoWay/F Modbus
type
Category Add- Address
ress
E3 (A3) Can be Not used.
changed
0100 0360
while
stopped.
0101 0361
0102 0362
0103 0363
0104 0364
0105 0365
0106 0366
0107 0367
010E 036E
0115 0375
0116 0376
0117 0377
Not used.
0200 0560
0300 0760
0400 0960
Note The decimal point position is determined by the sensor selection. In this case, however, the 0 (****) dec-
imal point position setting will be treated as a setting of 1 (***.*).
Variable CompoWay/F Modbus
type
Category Add- Address
ress
E4 (A4) Can be 0100 0380
changed
while
stopped.
0101 0381
0102 0382
0103 0383
0104 0384
0105 0385
0106 0386
Not used.
0200 0580
Parameter name
Alarm 1 Type - CH1 H' 00000000: Alarm function OFF (0)
H' 00000001: Upper and lower limit alarm (1)
H' 00000002: Upper limit alarm (2)
H' 00000003: Lower limit alarm (3)
H' 00000004: Upper and lower limit range alarm (4)
H' 00000005: Upper and lower limit alarm with standby
sequence (5)
H' 00000006: Upper limit alarm with standby sequence
(6)
H' 00000007: Lower limit alarm with standby sequence
(7)
H' 00000008: Absolute value upper limit alarm (8)
H' 00000009: Absolute value lower limit alarm (9)
H' 0000000A: Absolute value upper limit alarm with
standby sequence (10)
H' 0000000B: Absolute value lower limit alarm with
standby sequence (11)
H' 0000000C: LBA (Loop Burnout Alarm) (12)
Alarm 1 Latch - CH1 H' 00000000: Disabled (0)
H' 00000001: Enabled (1)
Alarm 1 Hysteresis - CH1 H' 00000001 to H' 0000270F (0.1 to 999.9) (See note.)
Alarm 1 Open in Alarm - CH1 H' 00000000: Close in alarm (0)
H' 00000001: Open in alarm (1)
Alarm 1 ON Delay - CH1 H' 00000000 to H' 000003E7 (0 to 999)
Alarm 1 OFF Delay - CH1 H' 00000000 to H' 000003E7 (0 to 999)
Alarm 1 SP Selection - CH1 H' 00000000: Ramp SP (0)
H' 00000001: Target SP (1)
Alarm 2 Type - CH1 The rest are the same as Alarm 1.
Alarm 3 Type - CH1
LBA Detection Time - CH1 H' 00000000 to H' 0000270F (0 to 9999)
LBA Level - CH1 H' 00000001 to H' 0000270F (0.1 to 999.9) (See note.)
LBA Band - CH1 H' 00000000 to H' 0000270F (0.0 to 999.9) (See note.)
Alarm 1 Type - CH2 The rest are the same as channel 1.
Alarm 1 Type - CH3
Alarm 1 Type - CH4
Parameter name
CT1 Assignment H' 00000000: Disabled (0)
H' 00000001: Control output 1 (1)
H' 00000002: Control output 2 (2)
H' 00000003: Control output 3 (3)
H' 00000004: Control output 4 (4)
Heater Burnout 1 Latch H' 00000000: Disabled (0)
H' 00000001: Enabled (1)
Heater Burnout 1 Hysteresis H' 00000001 to H' 000003E8 (0.1 to 100.0)
HS Alarm 1 Latch H' 00000000: Disabled (0)
H' 00000001: Enabled (1)
HS Alarm 1 Hysteresis H' 00000001 to H' 000003E8 (0.1 to 100.0)
Heater Overcurrent 1 Latch H' 00000000: Disabled (0)
H' 00000001: Enabled (1)
Heater Overcurrent 1 Hysteresis H' 00000001 to H' 000003E8 (0.1 to 100.0)
CT2 Assignment The rest are the same as from CT1 Assignment to
Heater Overcurrent 1 Hysteresis.
Setting (monitor) range
Setting (monitor) range
Appendix
De- Unit Attrib- Target Unit
fault utes
TC4/ HFU
TC2
●
2 --- ch ---
●
0 --- ch ---
●
0.2 EU ch ---
●
0 --- ch ---
●
0 s ch ---
●
0 s ch ---
●
0 --- ch ---
●
0 s ch ---
●
8.0 EU ch ---
●
3.0 EU ch ---
TC4 ---
TC4 ---
De- Unit Attrib- Target Unit
fault utes
TC4/
TC2
1 --- IO TC2 ---
0 --- IO TC2 ---
0.1 A IO TC2 ---
0 --- IO TC2 ---
0.1 A IO TC2 ---
0 --- IO TC2 ---
0.1 A IO TC2 ---
2
249
HFU