Lilin 66-1022CSB-2B Installation Manual

D/N HD IP CAMERA
Installation Guide
P
art Description & Dimensions
1
2
3
4
110mm
50mm
5
=
Extin: IR cut removable external control input.
I
nstallation
SUITABLE LENSES
Lenses used must be either C or CS mount type. The protrusion behind the
mounting surface must fit within the following requirements:
C - mount lens CS - mount lens
9mm or less 4mm or less
FITTING THE LENS
Remove the lens mount cap.
1
Screw in the C mount ring until it is secured. (When using a CS mount
2
lens, skip this step.)
Screw in the lens until it is secure.
3
N.O. DIN EXTIN
14
+5V COM. GND
. .
N O DIN
+
5V COM GND
1 2 3 4 5 6
VIDEO OUT
1 2 3 4 5 6
6
7
AUDIO OUT AUDIO IN
8
POWER
DC12V
SD CARD
9
70mm
① Focal Length Adjustment Ring ⑨ Micro SD Card Slot
and Locking Screw ⑩ Audio Output 3.5mm Phone Jack
② Lens Mount Cap ⑪ Audio Input 3.5mm Phone Jack
③ Microphone
⑫ RJ-45 Network Connector and Indicator LEDs
④ Light Sensor
Green(LINK): Network connection. This LED lit.
⑤ Auto Iris Connector (4-Pin Socket)
Orange(ACT): Data communications.
⑥ Live Video
This LED flashes.
⑦ DC12V Power Input Jack
(This network camera support PoE)
(DC12V ±10 %) ⑬ Reset Key
⑧ Power LED ⑭ Alarm In/Out, Extin
Insert the lens plug into the AUTO IRIS connector. (when fitting a manual
4
iris lens, skip this step.)
Adjust the focal length by turning the focal length adjustment ring.
5
(Using hexagon screw driver to loose or tighten the screw.)
CAUTION
Keep the lens mount cap on the
camera when not attaching a lens.
FITTING THE CAMERA
1. The mounting hole is on the top or bottom of the camera.
2. Tighten the screw to the mounting hole. Please refer to the following
dragram.
S
ystem Architectures
For connecting IP Camera series to the network, please follow one of the
system architectures:
(1). Use DC12V power adaptor and network switch connected to a network.
66-1022CSB-2B
LAN
Non-PoE Switch
IP CAMERA
13
(2). Use with PoE of the network switch connected to the network.
EXTIN
RESET
LAN
LAN
PoE Switch
IP CAMERA
12
11 (3). Use PoE power injector and the network switch connected to the network.
10
LAN
PoE Power Injector
IP CAMERA
B
efore Accessing IP Cameras
Before accessing the IP camera, make sure that the camera's RJ-45
network, audio, and power cables are properly connected. To set the IP
address, consult your network administrator for an available IP address.
The default IP address for each IP camera is 192.168.0.200. Users can use
the default IP address for verifying the camera's network connection.
E
mergency Factory Default
To restore the hardware to factory default settings, please follow these steps:
1.Press and hold "RESET Key" for 10 seconds and release.
2.Wait for about 40 seconds, and the network LED light should turn off, and
go back on again.
3.The camera is now restored to factory default settings, and will reboot
automatically.
4.Search for the IP device using the IPScan software.
5.Start the IP device via an Internet browser.
6.Enter the username and password to operate.
NOTE1: The factory default username and password are empty, and the
user can set an account for login.
NOTE2: The IP address will revert to the default setting of 192.168.0.200.
S
oftware Requirements
Universal ActiveX software components are required for web interface
display of JPEG or Full HD video. When you login to the IP camera by
Internet Explorer, the security warning dialog box will prompt the
installation of the Universal ActiveX. Click Install to download it.
C
onfiguring IP Addresses via Web Interface
To change an IP address via web interface, type the default IP address
(192.168.0.200) in the Internet browser and follow the steps below:
1. Login to the Full HD IP camera with the set username and password.
2. Click Basic Mode configuration hyperlink.
LAN / Internet
3. Click Network->General hyperlink.
4. Change the IP address, subnet mask, gateway, or HTTP port for the IP
camera.
PC
5. Click Submit to verify the settings.
DC12V Adaptor
C
onfiguring IP Addresses with IPScan Software
To change the settings of the IP address, subnet mask, gateway, or HTTP
LAN / Internet
port, you can follow the steps below:
1. Run the IPScan software.
PC
2. Click Refresh. All available devices should be listed in the device list.
3. Select your device from the list provided.
4. Change the IP address, subnet mask, gateway, or HTTP port for the IP
LAN LAN / Internet
camera.
AC
5. Click Apply to submit the settings.
Non-PoE Switch
6. Click Refresh to verify the settings.
PC
L
ogin
The factory default username and password are empty. To login to the Full
HD IP camera, please set the username and password on the login page.
Press [Login] to complete the setting and login simultaneously.
Password have to meet the following criteria:
1. More than or equal to 8 characters.
2. Allow uppercase letter, lowercase letter, number digit, and special
character.
3. Must have at least three types of character sets.
IPCAM