Angled base - full ends, straight base cutaway ends, modified base cutaway ends, straight base with full ends, storage
unit at rear, straight base - full ends, angled base - full ends, metal end panel with sink, rear sliding doors - plexi plenum, with pat (44 pages)
Service non-refrigerated bakery merchandisers (17 pages)
Summary of Contents for Structural Concepts Reveal NE3613DSSV
Page 1
READ AND SAVE THESE INSTRUCTIONS Reveal ® USER SCC P/N MANUAL 20-88455 REVEAL® SLIDE-IN, SELF-SERVICE, DRY (AMBIENT) MERCHANDISERS > REAR SLIDING DOORS OR REAR PANEL > CAUTION! DO NOT PUSH OR PULL ON GLASS END PANELS! > ONLY USE HANDLES (AT EACH END OF CASE) TO PUSH OR PULL CASE INTO POSITION! Model NE4827DSSV With Rear Sliding Doors Model NE4827DSSV With Rear Panel Structural...
Regulations, title 17, section 95374. not covered by warranty. • This disclosure statement has been reviewed and approved by Structural Concepts and Structural LAMP REPLACEMENT PRECAUTIONS Concepts attests, under penalty of perjury, that these • Following lamp replacement guidelines can prevent statements are true and accurate.
WIRING DIAGRAM / SEALING COUNTER-MOUNTED UNITS WIRING DIAGRAM SEALING COUNTER-MOUNTED UNITS • • Each case has its own wiring diagram folded and in a Proper sealing of base support to counter prevents packet. accumulation of dust, residue and liquids as well as •...
INSTALLATION: TOE-KICK & REAR PANEL REMOVAL / REMOVING CASE FROM PALLET 1. Remove Front Toe-Kick From Case • To prevent damage to case, remove front toe-kick from case before removing from pallet. • Place front toe-kick in secure location while removing case from pallet. Upper Rear Toe-Kick Panel...
INSTALLATION, CONT’D: PREPARE CASE FOR COUNTER: REAR PANELS / MAGNETS / HANDLES 5. Prepare Case For Counter: Rear Panels 7. Prepare Case For Counter: Side Handles • Rear panels must remain OFF case while it is > Slide-In Units: Side handles MAY remain on case if slid in (or dropped into) counter.
INSTALLATION, CONT’D: BUBBLE-WRAPPED GLASS (FOR SHELVING) 8. Remove Bubble-Wrapped Glass 9. Remove Glass From Bubble-Wrap / (For Shelving) From Case Carefully Place Them On Shelves • Carefully remove bubble-wrapped glass shelving • Remove glass (for shelves) from its bubble-wrap. pieces from case. •...
INSTALLATION, CONT’D: SHELVING ASSEMBLY COMPONENTS 10. Shelving Assembly Components is installed so shelves can be disassembled (to clean or service). • Check that glass shelving is in proper position G. Rear shelf support rail before placing product in case H. Left and right glass shelf/cover assemblies (glass •...
INSTALLATION, CONT’D: APPLY SEALANT / SLIDE IN (OR DROP-IN) COUNTER / ENERGIZE CASE 11. Apply Silicone Sealant To Underside of Base Support / Place Case On/Into Counter • To assure a secure seal, thoroughly clean both counter and underside of base support prior to proceeding.
INSTALLATION, CONT’D: OPTIONAL ACRYLIC SECURITY COVER D. Upper acrylic security cover must rest against upper 15. Optional Acrylic Security Cover security cover stop. Lock at both ends of cover with Note: Illustrations reflects Model NR4835RSS; it locking mechanism. may not reflect every feature or option of your case. >...
CASE DESIGN: FRONT VIEW OF SLIDE-IN, DRY (AMBIENT) SELF-SERVICE MERCHANDISERS 1. Front View Of Slide-In, Dry (Ambient) Self-Service Merchandisers • Model NE4827DSSV is illustrated below. • See next page for rear view. Model NE4827DSSV Slide-In Unit (Shown) May Not Exactly Reflect Every Feature or Option of Your Particular Case.
CASE DESIGN, CONT’D: REAR VIEW OF SLIDE-IN, SELF-SERVICE UNITS 2. Rear View Of Slide-In, Self-Service Units Model NE4827DSSV Is Shown. It May • Slide-in unit with rear sliding doors is illustrated below. Not Exactly Reflect Every Feature or • Certain models may have rear panels. Option Of Your Particular Case.
CASE DESIGN, CONT’D: POWER CORD & PLUG / LED LIGHT SWITCH LOCATIONS / LED LIGHTS 3. Power Cord and Plug Model NE4827DSSV Slide-In Unit (Shown) • Power cord and plug (for LED lights) is at case May Not Exactly Reflect Every Feature or rear (shown below).
CASE DESIGN, CONT’D: REAR SLIDING DOORS VS. REAR PANEL / DOOR OPERATION 6. Rear Sliding Doors vs. Rear Panel • Self-service cases may have either rear panel or rear sliding (and removable) doors. • Unit with rear sliding doors is shown below. •...
CLEANING SCHEDULE (TO BE PERFORMED BY STORE PERSONNEL) FREQUENCY INSTRUCTIONS Daily Glass Surfaces: Clean side glass and shelves with household or commercial glass cleaner. Daily Acrylic Surfaces (Sneeze Guard/Optional Acrylic Security Cover): • Clean: Use soft, clean cloth dipped in solution of warm water and small amount of mild, liquid soap.
Troubleshooting to be performed by trained service providers only is on next page. If case light still do not come on, it may need to be replaced. • Contact Structural Concepts’ Technical Service Department for replacement light (see TECHNICAL SERVICE section of this manual for contact information). •...
TROUBLESHOOTING (TO BE PERFORMED BY TRAINED SERVICE PROVIDERS ONLY) CONDITION TROUBLESHOOTING Case Lights Are See TROUBLESHOOTING (TO BE PERFORMED BY STORE PERSONNEL) Not Working section in manual (previous sheet) for most common troubleshooting solutions. Check power. • If power is not supplied to the case, facility may have faulty power distribution. •...
TECHNICAL SERVICE page in this manual for • Serial labels are affixed at a wide range of places instructions on contacting Structural Concepts’ (on the header, at case rear, behind panels or Technical Service Department. toe-kicks, on electrical boxes, etc.).
STRUCTURAL CONCEPTS TECHNICAL SERVICE CONTACT INFORMATION & LIMITED WARRANTY YOU MUST HAVE THE FOLLOWING INFO AVAILABLE TECH SERVICE/WARRANTY CONTACT INFO: BEFORE CONTACTING STRUCTURAL CONCEPTS: 1 (800) 433-9490 / EXTENSION 1 SERIAL NO. / MODEL NO. / STORE NO. / STORE...
Need help?
Do you have a question about the Reveal NE3613DSSV and is the answer not in the manual?
Questions and answers