Related Manuals for bimota TESI H2 2022
Summary of Contents for bimota TESI H2 2022
- Page 1 BIMOTA TESI H2 IO.PV.02 _Assembly and preparation manual Tesi H2 Rev1_18-10-2022...
- Page 2 Bimota and their Bimota Dealers. This Assembly and WARNING Preparation Manual explains step by step...
-
Page 3: Table Of Contents
Table of Contents Uncrating ........................4 Opening Crate......................4 Parts Check ......................10 Preparation ......................14 Battery Service......................14 Engine Oil(4-stroke) ....................17 Coolant ........................18 Drive Chain.......................20 Brakes ........................21 Suspension system ....................23 Wheels ........................27 Headlight ........................28 Remove anticorrosive treatments .………………………………........29... -
Page 4: Uncrating
Uncrating Opening Crate Crates have sharp edges and may have WARNING nails or screws that can cause cuts and injury. Always wear protective gloves, boots protection when uncrating to prevent injury. Figure 1 Screwdriver WARNING The steel crate panel plates and fasten- ers have sharp edges. - Page 5 2. Then it is the turn of the small panels: the case looks like in the image on the side. 3) The wooden frame is connected with screws to the side panels in the points identified by the arrows and therefore to open the case you need to unscrew these screws.
- Page 6 4. Then unscrew the screws that connect the wooden frame to the base of the crate.
- Page 7 5) Then remove the bubble wrap film that wraps the bike.
- Page 8 6) The 4 anchoring straps are removed, 2 per wheel.
- Page 9 Inside the case, in addition to the unit itself, there’s the kit supplied by Bimota which consists in the Arrow titanium exhaust, the Bimota bikes cover , the Tesi main stand , the tool to adjust eccentric of footrest and...
-
Page 10: Parts Check
Parts Check • Open the parts box, and check the parts against the illustrations. Part Name Titanium exhaust system Tesi main stand rear wheel Tesi main stand front/rear wheel Bike cover Eccentric tool adjuster Front wheel disassembly tool Titanium exhaust system... - Page 11 Tesi main stand rear wheel Tesi main stand fornt/rear wheel...
- Page 12 Bike cover Eccentric tool adjuster...
- Page 13 Front wheel disassembly tool...
-
Page 14: Preparation
Preparation Battery Service The battery used in this motorcycle is a sealed type and never needs to be refilled. Follow the procedure for activating a new battery to ensure the best possible battery performance. Seat The seat need to be removed to reach the battery. - Page 15 A. Fuse B. Battery C. Rubber support D. Dignostic connector E. Starting relay The battery installed in this motorcycle is sealed type, so it is not necessary to check the battery electrolyte level or add distilled water. Connect the positive (+) cable to the Positive (+) terminal, and black cable to the negative (-) terminal.
- Page 16 If it drops below 12.8 volts, the battery should be charged using an appropriate charger (check with your Bimota dealer). If you will not be using the motorcycle for longer than two weeks, the battery should be charged using an appropriate recharger.
-
Page 17: Engine Oil(4-Stroke)
O-ring with a new one. Oil and/or Oil FilterChange • The oil change and oil filter replacement should be done by an authorized Bimota dealer. A.Engine Oil DrainBolt B.Oil Filter Tightening Torque Engine Oil Drain Bolt: 25 N·m (2.5 kgf·m, 18 ft·lb) Oil Filter: 17 N·m (1.7 kgf·m, 13 ft·lb) -
Page 18: Coolant
Although 10W-40 engine Recommended Engine Oil recommended oil for most conditions, the oil Type: viscosity may need to be changed to API SG, SH, SJ, SL or SM with JASO accommodate atmospheric conditions in your MA, MA1 or MA2 riding area. rating Viscosity: SAE 10W-40 NOTE... - Page 19 Coolant Requirement NOTICE WARNING If hard water is used in the system, causes scale Coolant containing corrosion in- accumulation in the water hibitors for aluminum engines passages, considerably radiators include harmful reduces the efficiency of the chemicals for human body. cooling system.
-
Page 20: Drive Chain
Drive Chain Drive Chain Lubrication Lubrication is necessary after riding through rain or on wet roads, or any time that the chain appears dry. Use a lubricant for sealed chains to Prevent deterioration of chain seals. If the chain is especially dirty, clean it using a cleaner for sealed chains following the instructions supplied by the chain cleaner manufacturer. -
Page 21: Brakes
If you feel there is something wrong when applying the brakes, WARNING have the brake system checked by Air in the brake lines diminish authorized Bimota dealer braking performance immediately. cause an accident resulting in in- jury or death. If the brake lever or... - Page 22 1 mm (0.04 in.), replace both pads in the caliper as a set. Pad replacement should be done by an authorized Bimota dealer. A.Front Brake Fluid Reservoir B.Upper LevelLine C.Lower Level Line...
-
Page 23: Suspension System
Rebound Damping Force Adjustment There is no mounting instruction be- The adjuster is located at the upper end cause the original Bimota setting is given as of the rear shock absorber. for this shock absorber. Öhlins can accept the overhaul of your Standard shock absorber at your cost. - Page 24 Compression Damping Force Adjustment There is no mounting instruction be- cause The adjuster is located at the upper end of the original Bimota setting is given as for this the rear shock absorber. shock absorber. Öhlins can accept the overhaul of...
- Page 25 Front shock absorber Damping Force Settings Softest setting Hardest setting Standard limit limit Rebound 22 clicks** 14 clicks** Adjuster Position: Compression 22 clicks** 12 clicks** Damping Force Weak ←→ Strong Setting Soft ←→ Hard Load Light ←→ Heavy Road Good ←→...
- Page 26 Rear shock absorber Damping Force Settings Softest setting limit Standard Hardest setting limit Rebound 22 clicks** 12 clicks** Adjuster Po- sition: Compression 22 clicks** 14 clicks** Damping Force Weak ←→ Strong Setting Soft ←→ Hard Load Light ←→ Heavy Road Good ←→...
-
Page 27: Wheels
Wheels Tire Pressure Inspection Remove the air valve cap. • Check the tire pressure often, using an accurate gauge. • Make sure to install the air valve cap securely. ○ NOTE ○ Tire pressure is affected by changes in Measure the tire pressure when ambient temperature and altitude, the tires are cold (that is, when and so the tire pressure should be... -
Page 28: Headlight
Headlight Headlight aiming should be done by an authorized Bimota dealer. Horizontal Adjustment The headlight beam is adjustable horizontally. If not properly adjusted horizontally, the beam will point to one side rather than straight ahead. • Turn the horizontal adjuster in or out until the beam points straight ahead. -
Page 29: Remove Anticorrosive Treatments
Cleaning from anticorrosive treatments WARNING An anticorrosive treatment applied to the brake discs will increase braking Clean the front and rear brake discs, distance and can cause an accident swingarm, plate, right footrest support and resulting in serious injury or death. Remove the anticorrosive treatment left footrest support using alkaline solvent.