Error - Cause - Error Correction - Eaton D64RP410 Manual

Function 4: Reset to factory settings/Reset parameters
60000 Function Uint16 2
selection
60001 Pattern value Uint16 2
part 1
60002 Pattern value Uint16 2
part 2
60003 Type of reset Uint16 2
Function 6: Test
60000 Function Uint16 2
selection
60001 Pattern value Uint16 2
part 1
60002 Pattern value Uint16 2
part 2
60003 Type of test Uint16 2
Function 7: Reset
60000 Function Uint16 2
selection
60001 Pattern value Uint16 2
part 1
60002 Pattern value Uint16 2
part 2
60003 Type of reset Uint16 2
WO 4 N/A
→ Selection
of "Reset to
factory
settings/Reset
parameters"
function
WO 62663 N/A
→ Security
pattern must be
written
for the function
to be executed
WO 1304 N/A
→ Security
pattern must be
written
for the function
to be executed
WO 1 N/A
→ Reset to
factory settings
excluding
interface
parameters
2
→ Reset to
factory settings
including
interface
parameters
WO 6 N/A
→ Selection
of the "Test"
function
WO 32343 N/A
→ Security
pattern must be
written for the
function to be
executed
WO 0 N/A
→ Security
pattern must be
written for
the function to
be executed
WO 3 N/A
→ Start RCM
test
WO 7 N/A
→ Selection of
"Reset" function
WO 13623 N/A
→ Safety
pattern must be
written for the
function to be
executed
WO 0 N/A
→ Security
pattern must be
written for the
function to be
executed
WO 1 N/A
→ Reset of the
alarm message
when fault
memory is
enabled
GROWND FAULT RELAY D64RP410 IL54032 September 2023 www.eaton.com
6 Error – Cause – Error correction
6 Error – Cause – Error correction
Error pattern Cause
RS-485
Unstable Missing termination
system due to incorrect
commissioning
or defective
component.
No device is
terminated.
Faulty termination
due to incorrect
configuration
or defective
component. Only
one or more than
two devices are
terminated.
No Incorrect
communication configuration:
different baud
rates between bus
devices.
Incorrect
connection:
terminals A and B
are mixed up.
Alarm relays
Relays do not No alarm message
energise due to defective
component or
defective controlling
devices. No alarm
source has been
assigned.
Relays do not No alarm reset
de-energise due to sticking or
defective relay.
Switching current
> 5 A.
No switching of
the relay due to
excessive preloads
on contacts.
Enclosure
Broken screw- Device becomes
mounting detached due to
brackets broken mounting
brackets.
Non-compliance Insufficient
with the insulation due to
insulation insufficient distance
guideline between mounting
screws and
connecting wires.
Terminals
Wires detach Due to splicing
from the of wire ends, it
terminal is not possible to
insert them into
the terminal or hold
them firmly in the
terminal.
Wires cannot Ferrules with strong
be removed crimp impressions
from terminal get stuck in the
terminal
Correction Source
Configure the
terminating resistor,
determine the
terminating resistor
value and replace it if
necessary.
Configure the
terminating resistor,
check quality of the
bus signal.
Calibrate baud rates
between all bus
devices.
Establish correct bus
wiring.
Check relay for proper
function, replace
device if necessary.
Assign alarm sources.
Replace device, if
necessary. Observe
technical data of the
switching output.
Observe technical
data of the switching
output.
Preventive measure:
Use correct screw
type and observe max.
tightening torque. If
the screw-mounting
brackets are defective:
mount on DIN rail or
replace device.
Use screws with
plastic cover or mount
on DIN rail.
Use ferrules for
mounting and
connection to flexible
cables.
Use correct crimping
pliers for mounting
and connection with
flexible cables.
9