Table of Contents
Advertisement
Quick Links
ORIGINAL INSTRUCTIONS
S/N: 1002 AND ABOVE
PLEASE CONTACT GAGE BILT FOR
ALL OTHER SERIAL NUMBERS.
GB734SRVT5
INSTALLATION TOOL
GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE
E-MAIL US FOR A DISTRIBUTOR NEAR YOU.
GAGE BILT
44766 Centre Court, Clinton Twp., MI. 48038 USA
Ph: +1 (586) 226-1500 Fax: +1 (586) 226-1505
MADE in USA
solutions1@gagebilt.com / www.gagebilt.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Gage Bilt GB734SRVT5
Summary of Contents for Gage Bilt GB734SRVT5
- Page 1 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. GB734SRVT5 INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT 44766 Centre Court, Clinton Twp., MI. 48038 USA Ph: +1 (586) 226-1500 Fax: +1 (586) 226-1505 MADE in USA solutions1@gagebilt.com / www.gagebilt.com...
-
Page 2: Table Of Contents
Description and Technical Specifications ..........................4 Description of Functions ................................5 Safety Warnings ..................................6 Principle of Operation ................................7 How to set-up the GB734SRVT5 ............................... 8 How to use the GB734SRVT5 ..............................9 Maintenance and Hydraulic Thread Preparation ........................10 Filling ......................................11 Bleeding .................................... -
Page 3: Eu Conformity And Warranty
GAGE BILT DECLARATION OF CONFORMITY MANUFACTURER: Gage Bilt Inc. 44766 Centre Ct., Clinton Twp., Michigan U.S.A. +1(586-226-1500) WE DECLARE THAT THE EQUIPMENT SPECIFIED HEREIN CONFORMS TO THE FOLLOWING DIRECTIVES AND STANDARDS Machinery Directive 2006/42/EC EN12100-1 & 12100-2:2010 EN ISO 11148-1:2011... -
Page 4: Description And Technical Specifications
6.75 lbs. (3.06 kg). It has a 1.090” (27.69 mm) fastener setting stroke. The GB734SRVT5 split handle installation tool operates on 90 to 100 psi (6.2 - 6.9 bar) with 90 psi. (6.2 bar) providing maximum efficiency. At 90 psi, (6.2 bar) the GB734SRVT5 does not exceed 81.5 dB(A) and consumes .30 SCF/cycle (8.50 L/cycle). -
Page 5: Description Of Functions
Head Assembly Bleeder Screw Evacuation Tube Actuator Assembly-air Actuator Lever Assembly Air Hose Bleeder Screw Hydraulic Hose Handle Assembly Flow_Speed Control Valve Air Inlet Vacuum Regulator Image may not reflect actual tool GB734SRVT5 INSTALLTION TOOL SN#1002 AND ABOVE REV. 6/23... -
Page 6: Safety Warnings
4. Support the weight of the tool in a stand, tensioner or balancer, because a lighter grip can then be used to support the tool. GB734SRVT5 INSTALLTION TOOL SN#1002 AND ABOVE REV. 6/23... -
Page 7: Principle Of Operation
Piston Rod Assembly Air Piston moves down moves up Air Piston moves down Air exhaust Air exhaust Pressurized Oil Unpressurized Oil Pressurized Air Unpressurized Air Images may not reflect actual tool GB734SRVT5 INSTALLTION TOOL SN#1002 AND ABOVE REV. 6/23... -
Page 8: How To Set-Up The Gb734Srvt5
HOW TO SET-UP THE GB734SRVT5 WARNING: Only qualified and trained operators shall install, adjust or use the assembly power tool for non-threaded mechanical fasteners. WARNING: Operator MUST read and understand all warnings and cautions. WARNING: It is required that eye protection, hearing protection and safety boots be worn at all times while handling this equipment. -
Page 9: How To Use The Gb734Srvt5
HOW TO USE THE GB734SRVT5 WARNING: Only qualified and trained operators shall install, adjust or use the assembly power tool for non-threaded mechanical fasteners. WARNING: Operator MUST read and understand all warnings and cautions. WARNING: It is required that eye protection, hearing protection and safety boots be worn at all times while handling this equipment. -
Page 10: Maintenance And Hydraulic Thread Preparation
WARNING: Tool must be maintained in a safe working condition at all times and examined on a daily basis for damage or wear. Any repair must be done by qualified personnel trained on Gage Bilt procedures. WARNING: Excessive contact with hydraulic oil and lubricants must be avoided. -
Page 11: Filling
Hole marked #4 on Manifold Head Assembly (744306) Handle Assembly and facing upward. Power Cylinder hole Oil Passage hole O’ring (S832) ***Keep air hole free from oil*** Images may not reflect actual tool. GB734SRVT5 INSTALLTION TOOL SN#1002 AND ABOVE REV. 6/23... -
Page 12: Bleeding
Subtract dim “B” from dim “A”. If stroke is not consistent within 1/64" (.396 mm) repeat bleeding procedure until stroke met. For your consideration, Gage Bilt offers a depth gage (Pt.# A-1935) to help simplify and more accurately check your tool stroke. -
Page 13: Troubleshooting & How To Clean Vacuum Regulator
Note: The vacuum regulator may visually appear clean, but still may be contaminated with a thin film, therefore, the steps above should be performed to assure best performance. Image may not reflect actual tool GB734SRVT5 INSTALLTION TOOL SN#1002 AND ABOVE REV. 6/23... -
Page 14: Overhaul
Perform overhaul in a clean, well lit area using care not to scratch or nick any smooth surface that comes in contact with an o'ring. Use of Lubriplate® (Gage Bilt part no. 402723) or other lubricant is recommended during reassembly to prevent tearing or distorting of o'rings. - Page 15 Thread the actuator assembly-air (704130) all the way into manifold head (744306) with fingers. Insert and turn 5/8” open end box wrench / adjustable wrench and snug tight approximately 1/4 - 1/2 turn. Re-attach the actuator lever assembly (724017) with pin. GB734SRVT5 INSTALLTION TOOL SN#1002 AND ABOVE REV. 6/23...
- Page 16 Use needle nose pliers to grasp end of spring (744144), turning clockwise and pulling to dislodge from groove in casting. Valve spring installation tool (744251) will facilitate the proper installation of the spring (744144). Valve sleeve (743144) can be pulled out using valve sleeve removal tool (744152). GB734SRVT5 INSTALLTION TOOL SN#1002 AND ABOVE REV. 6/23...
-
Page 17: Parts List
PARTS LIST GB734SRVT5 INSTALLTION TOOL SN#1002 AND ABOVE REV. 6/23... - Page 18 PARTS LIST GB734SRVT5 INSTALLTION TOOL SN#1002 AND ABOVE REV. 6/23...
-
Page 19: Dexron® Iii Oil Safety Data (Sds)
Use material for its intended purpose or recycle if possible. Oil collection services are available for used oil recycling or disposal. Place contaminated materials in containers and dispose of in a manner consistent with applicable regulations GB734SRVT5 INSTALLTION TOOL SN#1002 AND ABOVE... -
Page 20: How To Assemble Evacuation Tube / Vacuum
HOW TO ASSEMBLE EVACUATION TUBE / VACUUM See pg. 13 on “how to clean vacuum” GB734SRVT5 INSTALLTION TOOL SN#1002 AND ABOVE REV. 6/23... -
Page 21: Nose Assembly Selection Chart
NOSE ASSEMBLY SELECTION CHART (Sold Separately) GB734SRVT5 INSTALLTION TOOL SN#1002 AND ABOVE REV. 6/23... -
Page 22: Alternative Style / Accessories
8N-743-24 and spare nose tip (10204) to convert to 6N-743-24. All other nose tips must be ordered separately. When ordering tool fastener specific, contact Gage Bilt for more information. “VT“ installation tools are not furnished with the nose assemblies above and must be ordered for your specific fastener. - Page 23 This page intentionally left blank GB734SRVT5 INSTALLTION TOOL SN#1002 AND ABOVE REV. 6/23...
- Page 24 Riveter Kits Available (Sold Separately) Gage Bilt offers a wide selection of standard and custom kits tailored to your needs. Contact us for more information. Approved Split Handle Installation Tool Backpacks For 5ft hose Split System Tools. (Sold Separately) DEXRON® IS A REGISTERED TRADEMARK OF GENERAL MOTORS CORPORATION. LUBRIPLATE® IS A REGISTERED TRADEMARK OF FISKE BROTHERS REFINING. LOCTITE® IS A REGISTERED TRADEMARK OF HENKEL CORPORATION.
Need help?
Do you have a question about the GB734SRVT5 and is the answer not in the manual?
Questions and answers