Specifications - Makita TM3000C Instruction Manual

ENGLISH (Original instructions)

SPECIFICATIONS

Oscillation per minute
Oscillation angle, left/right
Overall length
• Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• The weight may differ depending on the attachment(s). The lightest and heaviest combination, according to
EPTA-Procedure 01/2014, are shown in the table.
Intended use
The tool is intended for sawing and cutting wood, plastic, gyp-
sum, non-ferrous metals, and fastening elements (e. g. unhard-
ened nails and staples). It is also intended for working soft wall
tiles, as well as dry sanding and scraping of small surfaces. It is
especially for working close to edge and flush cutting.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated and can, therefore, also be used
from sockets without earth wire.
Noise
The typical A-weighted noise level determined accord-
ing to EN62841-2-4:
Work mode: Sanding
Sound pressure level (L
Uncertainty (K) : 3 dB (A)
The noise level under working may exceed 80 dB (A).
The typical A-weighted noise level determined accord-
ing to EN62841-1:
Work mode: Cutting with plunge cut saw blade
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB (A)
The typical A-weighted noise level determined accord-
ing to EN62841-1:
Work mode: Cutting with segmental saw blade
Sound pressure level (L
Uncertainty (K) : 3 dB (A)
The noise level under working may exceed 80 dB (A).
The typical A-weighted noise level determined accord-
ing to EN62841-1:
Work mode: Scraping
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB (A)
NOTE: The declared noise emission value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared noise emission value(s) may
also be used in a preliminary assessment of exposure.
Model
Net weight
Safety class
) : 77 dB (A)
pA
) : 81 dB (A)
pA
) : 89 dB (A)
WA
) : 79 dB (A)
pA
) : 80 dB (A)
pA
) : 88 dB (A)
WA
6,000 - 20,000 (min
Wear ear protection.
WARNING:
The noise emission during actual
WARNING:
use of the power tool can differ from the declared
value(s) depending on the ways in which the
tool is used especially what kind of workpiece is
processed.
Be sure to identify safety mea-
WARNING:
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841-2-4:
Work mode: Sanding
Vibration emission (a
Uncertainty (K) : 1.5 m/s
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841-1:
Work mode: Cutting with plunge cut saw blade
Vibration emission (a
Uncertainty (K) : 1.5 m/s
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841-1:
Work mode: Cutting with segmental saw blade
Vibration emission (a
Uncertainty (K) : 1.5 m/s
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841-1:
Work mode: Scraping
Vibration emission (a
Uncertainty (K) : 1.5 m/s
NOTE: The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
4 ENGLISH
TM3000C
-1
)
1.6° (3.2° total)
275 mm
1.4 kg - 1.5 kg
/II
2
) : 2.5 m/s or less
h
2
2
) : 6.5 m/s
h
2
2
) : 3.0 m/s
h
2
2
) : 5.5 m/s
h
2