Table of Contents
Advertisement
Quick Links
PA25609A01
PES197 & PES197/E
Rev. 04 1-2013
PORTABLE EMBOSSING SYSTEM
© Panduit Corp. 2013
Panduit Corp. • Tinley Park, IL USA
Technical Support:
Tel.: 888-506-5400, Ext. 83255
Website: www.panduit.com
Panduit Europe • EMEA Service Center
Almelo, Netherlands
Email:
Tel.: +31 546 580 452 • Fax: +31 546 580 441
techsupport@panduit.com
For Regional Contact Information,
see Page 18
Advertisement
Table of Contents
Related Manuals for Panduit PES197
Summary of Contents for Panduit PES197
- Page 1 PA25609A01 PES197 & PES197/E Rev. 04 1-2013 PORTABLE EMBOSSING SYSTEM © Panduit Corp. 2013 Panduit Corp. • Tinley Park, IL USA Technical Support: Tel.: 888-506-5400, Ext. 83255 Website: www.panduit.com Panduit Europe • EMEA Service Center Almelo, Netherlands Email: Tel.: +31 546 580 452 • Fax: +31 546 580 441 techsupport@panduit.com...
-
Page 2: Table Of Contents
OILING THE TROLLEY TRACK AND CLAMP GUIDE ..........17 CONTACT INFORMATION • For Technical Support: ....18 NOTE: In the interest of higher quality and value, Panduit products are continually being improved and updated. Consequently, pictures may vary from the enclosed product. -
Page 3: Setup And Installation Guide
PES197 and PES197/E: ENGLISH SETUP and INSTALLATION GUIDE UNPACKING The machine is delivered in a wooden packing case. This is due to its dimensions and weight and avoids the risk of damage to the machine. WARNING! THE MACHINE & CRATE WEIGHS 145 lbs. -
Page 4: Checking The Accessories
PES197 and PES197/E: ENGLISH CHECKING THE ACCESSORIES Before installing the machine check that all the accessories are present and that none have been damaged during transport. If any single element has been damaged the general working of the machine can be compromised. -
Page 5: Connecting Cables
Connect the AC cable to the rear input of the machine and to the proper AC source. Be sure to verify the power required. Identification Plate PES197 supplied with UL Plate PES197/E supplied with CE Plate Serial socket for... -
Page 6: Easy-Mark™ Software Installation
PES197 and PES197/E: ENGLISH Model : Machine model (EUR) Type : Embossing mode Volt : Power Supply Hz : Frequency supply Imax : Maximum current (Amps) SN : Serial Number Manufactured on Fuse rating Easy-Mark™ SOFTWARE INSTALLATION Insert the Easy-Mark™ Installation CD in the CD ROM driver. -
Page 7: Introduction
PES197 and PES197/E: ENGLISH INTRODUCTION The Panduit PES197 (110V) and PES197/E (220V) is an automatic personalization system for metal marker plates. It is computer operated and runs off of Panduit Easy-Mark™ software. (e.g.: PC compatible). The Panduit PES197 machines stamp exclusively Panduit MMP350, MMP350H, MMP350W38 and MMP350HW54 Metal Marker Plates. -
Page 8: System Specifications
Production Capacity PES197 & PES197/E PES197 & PES197/E Loading Hopper Power Supply 117V 60Hz PES197 Capacity 200 Plates Capacity 230 V 50 Hz PES197/E Unloading Hopper Current Absorption 4 A max Capacity 100 Plates Capacity Absorbed Power 250 W Fuse (5x20) - Page 9 PES197 and PES197/E: ENGLISH Safety Regulations and Operating Precautions • The machine should work in a closed room protected from dust and excessive humidity. The machine should be positioned in such a way that its distance from the walls, doors, windows, other machines or working positions guarantees immediate access in case of emergency, maintenance or repairs.
- Page 10 The machine has labels that indicate any danger areas. The meanings of these labels are explained below. Panduit cannot be held responsible for the consequences of not abiding by these safety rules when using the machine. Therefore, in the case of breakdown, please call for Technical Assistance.
-
Page 11: Machine Setup For Producing Plates
PES197 and PES197/E: ENGLISH MACHINE SETUP FOR PRODUCING PLATES • Unlock cover with cover key and open machine cover. (The cover will “latch” into the open position.) ADJUSTING THE LOADING UNIT Height Adjustment Adjust both height adjustment bars by loosening bar adjustment knobs ½ turn. Insert guide rail sizing block. - Page 12 PES197 and PES197/E: ENGLISH Bar Adjustment Knobs Height Adjustment Bars Figure 2 Figure 3 • Insert plates for embossing in the loader on the right side of the machine. • NOTE: The plates must be arranged in the loader with the Easy Feed humps facing up.
-
Page 13: Hopper Installation
PES197 and PES197/E: ENGLISH HOPPER INSTALLATION EXTERNAL HOPPER - NARROW TAG INSERT INTERNAL HOPPER - WIDE TAG INSERT a. Install External Hopper (see photo). b. Install proper External and Internal hopper inserts to match marker plate height. (see photo). c. Place appropriate plate weight on top of stack. Close machine cover by unlatching lock mechanism located in the left rear of inside cover. -
Page 14: Production - Hopper
Please refer to the section on “Error Messages and Problem Solving” for a description of the errors that can arise. CONSOLE The console of the PES197 and PES197/E has two units: a front display and a membrane keypad. The following list describes the structure of the front control panel: •... -
Page 15: Keyboard Description
PES197 and PES197/E: ENGLISH KEYBOARD DESCRIPTION The following list describes the 6 function keys and their actions: SETUP: This key is used to access the programming menu or other internal functions of the machine. A Password enables this command. CARD TEST: This key enables the production of test plates with a pre-determined format. -
Page 16: Displaying The Counters Of The Produced Plates
PES197 and PES197/E: ENGLISH EMB. MODE: This key selects the operational mode of the embossing cycle. It is used for tests and there are 8 choices based on the combinations of the following 3 modes: CONTINUOUS: Repeats the last processed plate continuously WITHOUT PLATE: Runs the operating cycle without controlling for the presence of a plate PAUSE: Executes each operation in response to the user input. -
Page 17: Error Messages
PES197 and PES197/E: ENGLISH ERROR MESSAGES In case of breakdown or operator error, the machine will show what caused the machine cycle interruption on the display and on the monitor. Contact technical support if code is not in table ERROR... -
Page 18: Trouble Shooting
PES197 and PES197/E: ENGLISH TROUBLE SHOOTING Contact technical support for assistance with the following adjustments: Gate Adjustment Factory set to .014 ± .002”. (Stainless Steel) Factory set to .016 ± .002”. (Aluminum) Marker Plate Hold Down Adjustment Factory set to .015 ± .003”. (Stainless Steel and Aluminum) OPTIONAL ACCESSORIES 1. -
Page 19: Oiling The Trolley Track And Clamp Guide
Every 6 months, Lubricate Every year Lubricant or as needed X & Y Guides 3-in-One Oil ® Contact Panduit Tool Service for the maintenance items listed below: High temperature red Carriage Bearing lithium grease High temperature red Dies lithium grease... -
Page 20: Contact Information • For Technical Support
PES197 and PES197/E: ENGLISH CONTACT INFORMATION • For Technical Support: Panduit USA – Corporate Headquarters, Tinley Park, IL USA Tel: 888-506-5400, ext. 83255 Website: www.panduit.com • E-mail: techsupport@panduit.com Panduit Latino America – Guadalajara, Jalisco, Mexico Latino America Tel.: 52 (333) 666 2501 • Fax.: 52 (333) 666 2510 Website: www.panduit.com •...