1. Manuals
  2. Brands
  3. Smartrise Manuals
  4. Controller
  5. HYDRO:EVOLVED
  6. Startup manual

Smartrise HYDRO:EVOLVED Startup Manual

Hide thumbs Also See for HYDRO:EVOLVED:
Table of Contents

Advertisement

Quick Links

Download this manual
VERSION 1 . 1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HYDRO:EVOLVED and is the answer not in the manual?

Questions and answers

Related Manuals for Smartrise HYDRO:EVOLVED

Summary of Contents for Smartrise HYDRO:EVOLVED

  • Page 1 VERSION 1 . 1...
  • Page 2 Hydro:Evolved Start-Up Guide...

  • Page 3: Table Of Contents

    Hydro:Evolved Start-Up Guide Table of Contents Introduction: Hydro:Evolved Start-Up Guide ..........1 Number of Floors ........................3 Floor Openings ........................4 Learning the Hoistway ......................4 Contract Speed ........................5 Level Maximum Run Distance ............... 6 NTS Buffer Distance Up and Down ..............7 Destination and Relevel Offsets ..............
  • Page 4 Hydro:Evolved Start-Up Guide Page intentionally left blank...

  • Page 5: Introduction: Hydro:evolved Start-Up Guide

    If the deceleration rate of the car is slow and the car hits the Terminal Stopping Distance (TSRD), reduce the deceleration rate of the valve (transition rate from high valve to leveling valve). Jul 14, 2022 ©2022 Smartrise Engineering, Inc. All Rights Reserved Page 1...
  • Page 6 Low Valve Cut Off Destination High and Low Times (Seconds) Valves On High Valve Cut Off Low Valve Cut Off Destination High and Low Times (Seconds) Valves On Page 2 ©2022 Smartrise Engineering, Inc. All Rights Reserved Jul 14, 2022...

  • Page 7: Number Of Floors

    NOTE: The number of floors should include any express zones that are serviced by other cars in the group. The opening map will reflect the floors the car serves. Jul 14, 2022 ©2022 Smartrise Engineering, Inc. All Rights Reserved Page 3...

  • Page 8: Floor Openings

    Check the top right corner of the Main screen to verify the DZ input to the CT board is high by. On the MR board, turn on DIP 5A. The Main screen changes from Normal to Hold UP/DN To Start. Page 4 ©2022 Smartrise Engineering, Inc. All Rights Reserved Jul 14, 2022...

  • Page 9: Contract Speed

    The contract speed is the maximum speed the elevator travels and is dependent upon the job configuration. Set the maximum speed of the car to run at contract speed. Set the Contract Speed. Jul 14, 2022 ©2022 Smartrise Engineering, Inc. All Rights Reserved Page 5...

  • Page 10: Level Maximum Run Distance

    From the HYDRO SETUP menu, scroll and select Level Maximum Run Distance. From LEVEL MAXIMUM RUN DISTANCE menu, enter the maximum run distance. Scroll right and press Save. Page 6 ©2022 Smartrise Engineering, Inc. All Rights Reserved Jul 14, 2022...

  • Page 11: Nts Buffer Distance Up And Down

    From the HYDRO SETUP menu, scroll and select NTS Buffer Distance Up or NTS Buffer Distance Down. From the NTS BUFFER DISTANCE UP or NTS BUFFER DISTANCE DOWN menu, enter the buffer distance. Scroll right and press Save. Jul 14, 2022 ©2022 Smartrise Engineering, Inc. All Rights Reserved Page 7...

  • Page 12: Destination And Relevel Offsets

    If the car is moving in down direction and stops outside the dead zone, go to step 5. Increase the up offset by 0.5in. Go to step 6. Increase the down offset by 0.5in. Scroll right and press Save. Page 8 ©2022 Smartrise Engineering, Inc. All Rights Reserved Jul 14, 2022...

  • Page 13: Relevel Offset

    From the RELEVEL OFFSET UP or RELEVEL OFFSET DOWN menu, enter the offset. The values are set after determing how far the cars have overshot the landing. Scroll right and press Save. Jul 14, 2022 ©2022 Smartrise Engineering, Inc. All Rights Reserved Page 9...

  • Page 14: Speed Thresholds

    Navigate to MAIN MENU | SETUP | HYDRO. From the HYDRO SETUP menu, scroll and select Speed Thresholds From the SPEED THRESHOLD menu, scroll and select the slowdown distance. Scroll right and press Save. Page 10 ©2022 Smartrise Engineering, Inc. All Rights Reserved Jul 14, 2022...

  • Page 15: Slowdown Distance

    From the HYDRO SETUP menu, scroll and select Slowdown Distance UP or DOWN. From the SLOWDOWN DISTANCE UP or SLOWDOWN DISTANCE DOWN menu, scroll and select the slowdown distance. Scroll right and press Save. Jul 14, 2022 ©2022 Smartrise Engineering, Inc. All Rights Reserved Page 11...

  • Page 16: Hydro Speed Setup

    Selecting yes will generate the values for slowdown distance up, slow down distance down, and threshold. a. if overshooting occurs, following instructions on for Car Overshooting and repeat step 1-4. Page 12 ©2022 Smartrise Engineering, Inc. All Rights Reserved Jul 14, 2022...

  • Page 17: Car Overshooting

    Increasing the time causes the car to slow down sooner which increases the slowdown distance. Scroll back to GENERATE THRESHOLDS AND DISTANCES and select YES. If YES is not selected, new thresholds and slowdowns are not generated. Jul 14, 2022 ©2022 Smartrise Engineering, Inc. All Rights Reserved Page 13...

  • Page 18: Adjust Leveling Time

    Decreasing the time causes the car to have a shorter slow down period which decreases the slowdown distance. Scroll back to GENERATE THRESHOLDS AND DISTANCES and select YES. If YES is not selected, new thresholds and slowdowns are not generated. Page 14 ©2022 Smartrise Engineering, Inc. All Rights Reserved Jul 14, 2022...

  • Page 19: Adaptive Slowdown™ System (U.s. Patent Pending)

    Note: Turning off Adaptive Slowdown™ system (U.S. Patent Pending) will reset all the slowdown distance learned and will cause the car to operate based on the settings on Hydro Speed Setup. Jul 14, 2022 ©2022 Smartrise Engineering, Inc. All Rights Reserved Page 15...

  • Page 20: Troubleshooting Adaptive Slowdown™ System (U.s. Patent Pending)

    • Navigating to MAIN MENU | SETUP | HYDRO | TSRD DISTANCE • Decrease the TSRD Distance to a lower value and repeat step 4 of the procedure. Page 16 ©2022 Smartrise Engineering, Inc. All Rights Reserved Jul 14, 2022...

  • Page 21: Monitoring Adaptive Slowdown™ System (U.s. Patent Pending)

    If the car stops before floor level, increase the distance by the amount the car needs to move up. Navigate to MAIN MENU | SETUP | FLOORS | TOO HIGH/ TOO LOW. Jul 14, 2022 ©2022 Smartrise Engineering, Inc. All Rights Reserved Page 17...

  • Page 22: Car Is Too High

    Adjust the stopping point of the car so the car stops at the exact floor level. For example, if the car stops 1.5”-2” above the floor level, add that distance to the learned position. Page 18 ©2022 Smartrise Engineering, Inc. All Rights Reserved Jul 14, 2022...

  • Page 23: Nts Alarm

    Once the NTS acceptance test has been completed, the NTS alarm can be disabled. Navigate to MAIN MENU | SETUP | HYDRO.| Disable NTS Alarm. From the DISABLE NTS ALARM menu, select ON to disable the alarm. Jul 14, 2022 ©2022 Smartrise Engineering, Inc. All Rights Reserved Page 19...

  • Page 24: Outside Of Dead Zone

    If the car is moving in down direction and stops outside the dead zone, increase the destination offset down by 0.5in. This value also determines when to cut the low valves off and the sliding distance after the low valves are cut. Page 20 ©2022 Smartrise Engineering, Inc. All Rights Reserved Jul 14, 2022...

  • Page 25: Adding Weights To An Empty Car

    DO NOT generate the threshold and distance after fine tuning the slowdown distance. This will override the fine-tuning values and generate new slowdowns depending on the factor in the up/down adjustments. Jul 14, 2022 ©2022 Smartrise Engineering, Inc. All Rights Reserved Page 21...

  • Page 26: Car Overshooting

    Increase the slowdown distance up from 2’ 09” to 3’ 02”. Place a car calls in up direction and see if the car still overshoots the floor. Repeat these steps , if the car still overshoots the floor. Page 22 ©2022 Smartrise Engineering, Inc. All Rights Reserved Jul 14, 2022...

  • Page 27: Adjust Leveling Time

    , if the car still has longer steady state of leveling to the floor. Continue adding a load to the car and verifying the slowdowns until the car is fully loaded. Jul 14, 2022 ©2022 Smartrise Engineering, Inc. All Rights Reserved Page 23...

  • Page 28: Store Floor Level

    13 Store Floor Level The store floor level stores the position of the floor level. Navigate to MAIN MENU | SETUP | FLOORS | STORE FLOOR LEVEL. View the floor level. Page 24 ©2022 Smartrise Engineering, Inc. All Rights Reserved Jul 14, 2022...

Table of Contents