Advertisement
The audio track can be customized only when recorded
in the 12-bit mode (_
pg. 28).
NOTES:
• Audio Dubbing is not possible ona tape recorded in
f 6-bit audio, on a tape recorded in the LP mode or on a
blank portion of a tape.
• To perform Audio Dubbing while watching on the
television, make connections (_-7pg. 16).
I Play back the tape to locate the point where editing
will start, then press PAUSE (11)_.
2 While holding A.DUB (8) _ on the remote control,
press PAUSE (11)_. "118" [_1and "MIC" (GR-DgO/D70
only) appear.
3 Press PLAY (l_) _, then begin "narrating".
Speak into the microphone.
• To pause dubbing, press PAUSE (11)_.
4 To end Audio Dubbing, press PAUSE (11)_), then
STOP (11)(_.
To hear the dubbed sound during playback...
..... set "t 2BIT MODE" to "SOUND 2" or "MIX" th the
Menu Screen (_
pg. 32),
NOTES:
• Sound is not heard from the speaker during Audio
Dubbing.
• When editing onto a tape that was recorded
at f 2*bit, the
otd and new souedtracks
are recorded separately.
• {f you dub onto a blank space on the tape, the sound may
be disrupted.
Make sure you only edit recorded areas.
• If feedback
or howling occurs during TV playback,
move
the camcorder's
microphone
away from the TV, or turn
down the TV's volume.
• If you change from 12-bit to 16-bit in mid_recordieg and
then use the tape for Audio Dubbing, it is not effective
from the point where 16_bit recording began.
• During Audio Dubbing, when the tape moves to scenes
recorded in the LP mode, scenes recorded
in f 6*bit audio
or a bIank portion, Audio Dubbing stops (_t_?pg. 50).
• To perform Audio Dubbing with a video unit connected
to
the camcorder's
AV connector, first set "S/AV INPUT" to
"ON" in the Menu Screen (_? pg. 31 ). "AUX" appears
instead of "MIC".
You can record a new scene into a previously recorded
tape, replacing a section of the odgthal recording with
minimal picture distodion at the in and outpoints. The
original audio remains unchanged.
NOTES:
• Before performing the following steps, make sure that
"TIME CODE" is set to "ON" in the Menu Screen
(_? pg. 31,32).
• Insert Editing is not possible on a tape recorded in the LP
mode or on a blank portion of a tape.
• TOperformInsert Editing while watching in the television,
make connections (_? pg. 16).
I
Play back the tape, locate the Edit=Out point and
press PAUSE (11)_. Confirm the time code at this
point (_
pg. 31,32).
Press REW (41<) _) until the Edit-In point is located,
then press PAUSE (11)_.
Press and hold INSERT (O) _) on the remote
control, then press PAUSE (11)_. "IIO" _ and the
Time Code (min.:sec.) appear and the camcorder
enters Insert-Pause mode.
4 Press START/STOP _1 to begin editing.
• Confirm the insert at the time code you checked in
step 1.
•To pause editing, press START/STOP _. Press it
again to resume editing.
To end Insert Editing, press START/STOP _, then
STOP (I)l_.
NOTES:
• Program AE with special effects (_
pg. 23) can be used
to spice up the scenes being edited during thsert Editing.
• During Insert Editing, the date and time information
changes.
• If you perform
Insert Editing onto a b{ank space on the
tape, the audio and video may be disrupted.
Make sure
you on{y edit recorded
areas.
• During Insert Editing, when the tape moves to scenes
recorded
in the LP mode or a blank portion, Insert Edtieg
stops (_
pg. 50).
Stereo microphone
EN USING
THE REMOTE
CONTROL
UNIT
36 ( -o9o
and GR-DZO only)
Advertisement
