Advertisement
Make sure "REMOTE" th the SYSTEM Menu is set
to "ON" (_ pg. 30) and the remote control is
pointed at the remote sensor O. The transmitted
beam's approximate effective distance for indoor
use is 5m (16ft).
To allow slow-speed search in either direction during
tape playback.
I To change from normal to Slow-Motion Playback,
press SLOW (.q) _ or (1_)(_ more than approx. 2
seconds. After approx. 5 minutes (approx. 20 seconds
with an 80-minute cassette) in Slow Rewind or approx.
5 minutes in Slow Forward, normal playback resumes.
nTo stop Slow-Motion Playback, press PLAY (1_)(_.
NOTES:
• YOUcan also engage Slow-Motion
PIayback fro_'n Still
Playback by pressing SLOW _) (_ more than approx.
2 seconds.
• During Slow-Motion
Playback, due to digital image
processing,
the picture may take on a mosaic effect.
• After SLOW (_1) _) or (1_)_) is pressed and held, the still
image may be displayed for a few seconds, followed by a
blue screen for a few seconds. This is not a malfunction.
• There may be a smaII margin between the slow-motion
playback
start point you chose and the actual start point
for Slow*Motion
Playback.
• During Slow-Motion
Playback, there will be disturbances
in video and the picture may seem unstable,
especially
with steady images• This is not a malfunction.
• During Slow-Motion
Playback, press PAUSE (11) _) to
pause playback.
To allow frame-by-frame search during tape playback.
I To change from normal to Frame-By-Frame
Playback, press SLOW (I.) _ repeatedly for forward or
SLOW (41)_) repeatedly for reverse. Each time it is
pressed, the frame is played back.
NOTE:
YOU can also engage Frame*By-Frame
Playback from Stilt
Playback by pressing SLOW (41) _) or (1.) (_ repeatedly.
To allow you to add creative effects to the playback
image.
I TO start playback, press PLAY (1_)(_.
2 Point the remote control at the camcorder's remote
sensor and press EFFECT (D. The PLAYBACK
EFFECT Select Menu appears.
3 Move the highlight bar to the desired effect by
pressing EFFECT _). The selected function is activated
and after 2 seconds the menu disappears.
• To deactivate the selected effect, press ON/OFF (_
on the remote control. Pressing it again re-activates
the selected effect.
• To change the selected effect, repeat from step 2
above.
NOTE:
The effects that can be used during playback
are Classic
Film, Monotone,
Sepia and Strobe. The effects work the
same in playback
as they did in recording.
Refer to page
23, 24 for more information•
To magnify the recorded image up to 44X at any time
during playback.
I Press PLAY (1_)(_ to find the scene of interest.
2 Press the Zoom Button T _) or W _ on the remote
control. Make sure the remote control isp(ointed at the
camcorder's remote sensor. Pressing T @) zooms in.
3 You can move the image on screen around to find a
particular portion of the picture. While holding down
SHIFT _, press _ (Left) _), ,'> (Right) _), _ (Up)
and _ (Down) _.
• To end zoom, press and hold W _) until magnification
returns to normal. Or, press STOP (11)_ and then
press PLAY (1_)(_.
NOTES:
• Zoom can also be used during slow-motion
and still
playback.
• Due to dithal image processing,
the quality of the image
may suffer.
Normalplayback
PressT
ili'iii!iii!!_i!ii' 'i_ii_!i_
.
_ii!i!ii_!!
_
TO move
image,
press
(Right)_ while keeping
SHIFT_[P helddown.
USING THE REMOTE
CONTROL
UNIT
EN
(GR-O9e and GR-O7O only)
35
Advertisement
