Motorline professional LINCE300 User's And Installer's Manual
Hide thumbs
Also See for LINCE300:
- User's and installer's manual (14 pages) ,
- User's and installer's manual (13 pages) ,
- User's and installer's manual (14 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Motorline professional LINCE300
Summary of Contents for Motorline professional LINCE300
- Page 1 LINCE LINCE USER’S AND INSTALLER’S MANUAL v12.0 REV. 08/2023...
-
Page 2: Table Of Contents
00. CONTENT 01. SAFETY INSTRUCTIONS INDEX STANDARDS TO FOLLOW 01. SAFETY INSTRUCTIONS ATTENTION: STANDARDS TO FOLLOW This product is certified in accordance with European 02. PACKAGE Community (EC) safety standards. INSIDE PACKAGE This product complies with Directive 2011/65/EU of the 03. -
Page 3: Safety Instructions
01. SAFETY INSTRUCTIONS GENERAL WARNINGS the motorized door or gate from being triggered involuntarily. • This manual contains very important safety and usage information. WARNINGS FOR TECHNICIANS very important. Read all instructions carefully before beginning the installation/usage procedures and keep this manual in a safe place •... - Page 4 01. SAFETY INSTRUCTIONS RESPONSABILITY • Attach the permanent label for the manual release as close as possible to the release mechanism. • Supplier disclaims any liability if: • Disconnect means, such as a switch or circuit breaker on the electrical •...
-
Page 5: Package
• 02 Capacitors [Only available with the 230v (8µf ) and 110v(20µf) models] 210mm • 01 User’s manual 01 • Loosen the 4 screws that fix the Lower Part to 02 • Remove Lower Part. 800mm (LINCE300) Middle Part. 280mm 1000mm (LINCE600) -
Page 6: Manual Release 5B
03. AUTOMATION 03. AUTOMATION CHANGE MOTOR DIRECTION MANUAL RELEASE 03 • Loosen the 4 screws of the Middle Part. 04 • Remove Middle Part. 01 • Remove the plastic cover from the back. Information engraved on the unlock shaft. D=Unlock || B=Lock 05 •... -
Page 7: Technical Specifications 6A
03. AUTOMATION 04. INSTALLATION TECHNICAL SPECIFICATIONS HEIGHT OF THE SUPPORTS The automation must be installed with a small inclination, to prevent water infiltration through the Model LINCE300 LINCE400 LINCE600 extension arm. 230V 230Vac 50/60Hz 230Vac 50/60Hz 230Vac 50/60Hz For this, the front support must be fixed to the gate with a height lower than the height of the rear •... -
Page 8: Interior Opening Installation Dimensions
04. INSTALLATION INTERIOR OPENING INSTALLATION DIMENSIONS In the diagrams illustrated below and on the next page, the dimensions for the installation of 300 (W: 895 ~ 900) automations are defined. Axis of rotation of the (EXTERIOR) motor, on the front support 98˚... -
Page 9: External Opening Installation Dimensions
04. INSTALLATION EXTERNAL OPENING INSTALLATION DIMENSIONS In the diagrams illustrated below and on the next page, the dimensions for the installation of 300 (W: 595 ~ 600) automations are defined. 95˚ 97˚ 92˚ Placing a stopper in the opening is recommended. 95˚... -
Page 10: Installation Steps
04. INSTALLATION 04. INSTALLATION INSTALLATION STEPS INSTALLATION STEPS 04 • Install automation on the supports Pay attention to installation dimensions mentioned on pages 6B, 7 and 8! • The automation must be placed on both supports at the same time to avoid leaving the automation suspended by only one of the supports. -
Page 11: Installation Map
04. INSTALLATION INSTALLATION MAP • INTERIOR • JUNCTION • EXTERIOR • MOTOR • KEY • FLASHING • ANTENNA • CONTROL PHOTOCELLS PHOTOCELLS SELECTOR LAMP BOARD • EXTERIOR PHOTOCELLS LEGEND: • Connection cables It is important to use stoppers at the opening and closing of the gate. If not respected, compo- It is important to use junction boxes for connections between motors, components and con- nents of the automation may suffer efforts for which they were not prepared, and as a result trol board. -
Page 12: Troubleshooting
05. TROUBLESHOOTING FINAL CONSUMERS INSTRUCTIONS INSTRUCTIONS FOR SPECIALIZED INSTALLERS Anomaly Procedure Behavior Procedure II Discovering the origin of the problem • Motor •Make sure you • Still not working • Consult a qualified 1 • Open control board and check if it has 230V/110V/24V power supply; doesn't work have power in the MOTORLINE technician. -
Page 13: Components Test
06. COMPONENTS TEST 06. COMPONENTS TEST 230V/110V MOTOR 24V MOTOR To detect if the malfunction is on the control board or on the motor is, sometimes, necessary to perform To detect which are the components with problems in a 24V automatism installation, it's sometimes tests with direct connection to a 110V/230V power supply. -
Page 14: Maintenance
07. MAINTENANCE MAINTENANCE CHECK MOTOR SUPPORTS CLEAN THE TUBE • Make sure that supports remain well fixed on the pillars and gate to ensure proper functioning of the equipment. • With a cloth soaked in lubricant spray, clean all the residues that accumulate in the automation tube.
Need help?
Do you have a question about the LINCE300 and is the answer not in the manual?
Questions and answers