Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Motorline professional BRAVO500-50
Summary of Contents for Motorline professional BRAVO500-50
- Page 1 BRAVO500 USER'S AND INSTALLER'S MANUAL v4.3 REV. 05/2022...
-
Page 2: Table Of Contents
00. CONTENT 01. SAFETY INSTRUCTIONS INDEX ATTENTION 01. SAFETY INSTRUCTIONS This product is certified in accordance with European STANDARDS TO FOLLOW Community (EC) safety standards. 02. PACKAGE INSIDE PACKAGE This product complies with Directive 2011/65/EU of the European Parliament and of the Council, of 8 June 2011, on 03. -
Page 3: Safety Instructions
01. SAFETY INSTRUCTIONS 01. SAFETY INSTRUCTIONS GENERAL WARNINGS WARNINGS FOR TECHNICIANS • This manual contains very important safety and usage information. • Before beginning the installation procedures, make sure that you very important. Read all instructions carefully before beginning the have all the devices and materials necessary to complete the installation/usage procedures and keep this manual in a safe place that installation of the product. - Page 4 01. SAFETY INSTRUCTIONS 01. SAFETY INSTRUCTIONS RESPONSABILITY • Disconnect means, such as a switch or circuit breaker on the electrical panel, must be provided on the product’s fixed power • Supplier disclaims any liability if: supply leads in accordance with the installation rules. •...
-
Page 5: Package
02. PACKAGE 03. OPERATOR INSIDE PACKAGE OPEN COVER Inside the package you will find the following components: During installation you will need to open the motor cover, to access 01• 01 motor Bravo500 07• 02 fixation plate of the limit switches various components on the inside. -
Page 6: Unlock Operator 6A
03. OPERATOR 03. OPERATOR UNLOCK OPERATOR TECHNICAL SPECIFICATIONS To open manually the gate in case of electric power failure or in case of damage, follow The specifications of the automatism BRAVO 500 are as follows: the below steps: BRAVO500 BRAVO500/110 •... -
Page 7: Installation
04. INSTALLATION 04. INSTALLATION INSTALLATION SITE PREPARATION SITE INSTALLATION – CREATE FOUNDATION To ensure full operation of the automatism, pay attention the following recommendations: • Read the entire manual at least once giving special attention to all notices marked with •... -
Page 8: Site Installation - Existing Foundation 8A
04. INSTALLATION 04. INSTALLATION SITE INSTALLATION – EXISTING FOUNDATION APPLICATION OF MOTOR In case there is already a foundation at the installation site, proceed as below: 60mm 60mm 01 • Remove the side covers of the motor 02 • Place the motor in the fixing plate. 01 •... -
Page 9: Installation Of Steel Gear Rack 9A
04. INSTALLATION 04. INSTALLATION INSTALLATION OF STEEL GEAR RACK INSTALLATION OF STEEL GEAR RACK Place the gate in the open position and unlock the motor! (p.03A). ) DETAIL 29 05 • Close the gate a bit, so that the rack is not being supported on the pinion anymore 01 •... -
Page 10: Installation Of Nylon Gear Rack 10A
04. INSTALLATION 04. INSTALLATION INSTALLATION OF NYLON GEAR RACK INSTALLATION OF NYLON GEAR RACK Place the gate in the open position and unlock the motor! (p.03A) 04 • Close the gate a bit, so that the rack is not being supported on the pinion anymore and apply another piece of rack (A), fitting it into the rack already installed (B), as you can see in detail of image 41. -
Page 11: Installation Of Plates The Limit Switches 11A
04. INSTALLATION 04. INSTALLATION INSTALLATION OF PLATES THE LIMIT SWITCHES CLUTCH ADJUSTMENT To start the disassembly of the control board, disconnect the power and have Place the gate in the open position and unlock the motor! (p.03A) maximum care when handling it. 01 •... -
Page 12: Map Of Installation
04. INSTALLATION MAP OF INSTALLATION • FLASH LAMP • ANTENNA • CONTROL • BRAVO500 • PHOTOCELL • PHOTOCELL • KEY SELECTOR BOARD LEGEND: • Cables of connection It is important to use stoppers on the opening and closing of the gate. If this is not It is important to use junction boxes for connections between motors, components and control board. -
Page 13: Troubleshooting
05. TROUBLESHOOTING 05. TROUBLESHOOTING FINAL CONSUMERS INSTRUCTIONS FINAL CONSUMERS INSTRUCTIONS SPECIALIZED TECHNICIANS INSTRUCTIONS SPECIALIZED TECHNICIANS INSTRUCTIONS Problem Procedure Behavior Procedure II Discovering the origin of the problem • Motor • Make sure you • Still not working • Consult a qualified 1 •... -
Page 14: Components Test
06. COMPONENTS TEST 07. MAINTENANCE SCHEMES FOR CAPACITORS MAINTENANCE To detect if the malfunction is on the control board or on the motor is, sometimes, • Check all screws of the automation necessary to perform tests with connection directly to a 110V/230V power supply. such as the fixing plate to the ground, For this, it is necessary to interpose a capacitor on the connection in order to the the plates of the limit switches, motor...
Need help?
Do you have a question about the BRAVO500-50 and is the answer not in the manual?
Questions and answers